共找到 5671 条与 合成树脂、塑料基础标准与通用方法 相关的标准,共 379 页
Test method for puncture resistance of plastic film and sheeting
Determination of polybrominated biphenyls and polybrominated diphenyl ethers in plastic products—Gas chromatography and mass spectrometry
Determination of polybrominated biphenyls and polybrominated biphenyl ethers in plastic products—High performance liquid chromatography
Plastics—Determination of temperature of deflection under load—Part 1:General test method
GB/T17037的本部分给出了热塑性塑料材料注塑试样所遵循的一般原理,给出了用于制备两种试样的模具设计的详细参考数据,例如GB/T37426规定的Al型和Bl型试样,提供了可再现的注塑条件,其目的是提供模塑过程主要参数的一致性描述,并在报告的模塑条件下建立统一的方法。 试样的可再现性制备所需的详细条件会随使用材料而有所变化,这些条件在相关材料的国家标准中有规定,或由相关方约定。 本部分适用于热塑性塑料材料注塑制备具有可再现性的多用途试样和长条形试样。 注,对丙烯且/丁二烯/荃乙烯(ABS)、苯乙烯/丁二烯(SB)和聚甲基丙烯酸甲酯(PMMA)的实验室之间试验表明,模具设计是保证试样的可再现性制备的重要因素之一。
Plastics—Injection moulding of test specimens of thermoplastic materials—Part 1:General principles,and moulding of multipurpose and bar test specimens
Plastics—Determination of temperature of deflection under load—Part 2:Plastics and ebonite
Plastics—Test specimens
Plastics—Assessment of the effectiveness of fungistatic compounds in plastics formulations
Determination of 3,3'-dichloro-4,4'-diaminodiphenylmethane in polymeric materials—Gas chromatography-mass spectrography
Plastics—Acquisition and presentation of comparable multipoint data—Part 2:Thermal and processing properties
Plastics—Polybutene(PB) moulding and extrusion materials—Part 2:Preparation of test specimens and determination of properties
Plastics—Polyether polyols/polymeric polyols—Determination of aldehydes and ketones
Plastics—Determination of tensile properties—Part 1:General principles
Plastics—Thermoplastic polyester (TP) moulding and extrusion materials—Part 1:Designation system and basis for specifications
GB/T36800 的本部分规定了利用热膨胀原理,使用热机械分析法(TMA)测定塑料固体状态时线性热膨胀系数的方法。 同时也规定了通过热机械分析法测定玻璃化转变温度的方法。 注:测量线性热膨胀系数可以使用各种类型的热膨胀仪器,本部分只涉及TMA仪器。
Plastics—Thermomechanical analysis(TMA)—Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
Plastics—Determination of tensile properties at high strain rates—Part 1:Equation fitting method
Determination of percent regeneration of cation exchange resins
Plastics—Thermomechanical analysis(TMA)—Part 1:General principles
Plastics—Polyamides—Accelerated conditioning of test specimens
GB/T 36374的本部分规定了用于砜聚合物模塑与挤出材料性能测试的试样制备过程和测试方法。本部分规定了被测试材料的处理方法以及模塑前的被测试材料和测试前的试样的状态调节要求。 本部分给出了砜聚合物模塑和挤出材料试样制备过程和条件以及用这些试样测试材料性能的方法,同时也列出了表征砜聚合物模塑和挤出材料所需的性能及其测试方法。 性能项目选自通用测试方法ISO 10350-1。砜聚合物模塑和挤出材料的其他一些特别重要的或广泛使用的测试方法也包含本部分中,特征性能可在ISO 25137-1中找到。 为了获得可比的及有重现性的测试结果,应按照本部分所规定的样件制备过程及状态调整方法、试样尺寸和测试方法进行。采用不同试样尺寸或样件制备方法的测试数据未必会一致。
Plastics.Sulfone polymer moulding and extrusion materials.Part 2:Preparation of test specimens and determination of properties
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号