G33 塑料型材 标准查询与下载

QB/T 5634-2021 钢塑复合压力管用电磁感应双热熔焊接管件

Electromagnetic induction double hot melt welded pipe fittings for steel-plastic composite pressure pipes

QB/T 5610-2021 硬质聚氯乙烯发泡建筑模板

Rigid polyvinyl chloride foam building template

QB/T 5584-2021 塑料气垫卷膜

Plastic air cushion roll film

QB/T 5608-2021 硬质聚氯乙烯低发泡型材

Rigid polyvinyl chloride low foaming profile

T/CECS 10022-2021 埋地用改性高密度聚乙烯（HDPE-M）双壁波纹管材

本文件规定了埋地用改性高密度聚乙烯（HDPE-M）双壁波纹管材的术语和定义、符号、缩略语、材料、产品分类、标记、结构、连接方式、技术要求、试验方法、检验规则、标志、运输和贮存。

Modified high-density polyethylene (HDPE-M) double-wall corrugated pipe for buried

ISO 7233:2021 橡胶和塑料软管和软管组件. 耐真空性能测定

This document specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows: — method A for hoses of nominal size up to and including 80; — method B for hoses of nominal size greater than 80; — method C for hoses of all dimensions. If not otherwise specified in the product standard, method C can be used as an alternative to methods A and B. Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall hose or hose assembly.

Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum

ISO 7432:2021 玻璃纤维增强热固性塑料管道和管配件. 检验设计带弹性体密封件的锁紧套筒连接件, 包括双插孔连接件的试验方法

This document specifies methods of test for joints with a locked socket and spigot, including doublesocket joints, and with elastomeric seals, for buried and above-ground glass-reinforced thermosetting plastics (GRP) piping systems. It covers methods of testing for leaktightness and resistance to damage of the joint only, when subjected to specified combinations of angular movement, compression (deformation) perpendicular to the pipe axis and internal pressure. It assumes that the joint will be exposed to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.3, 9.4 and 9.6 are applicable to joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals intended to be used in buried or aboveground applications. The bending tests detailed in 9.5 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations, where the tests can be considered appropriate. With the exception of the procedure detailed in 9.5, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.5 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is intended for type testing purposes. This document is applicable only to the joint and specifies methods of testing to prove its design.

Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals

ISO 10466:2021 玻璃纤维增强热固性塑料(GRP)管材. 耐初始环状变形可能性试验方法

This document specifies a method for testing the ability of glass-reinforced thermosetting plastics (GRP) pipes to withstand specified levels of initial ring deflection without displaying surface damage and/or structural failure.

Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection

DIN EN ISO 3949:2021 塑料软管和软管组合件. 液压用织物增强型. 规格(ISO 3949-2020, 修正版本2020-12); 德文版本EN ISO 3949-2020

This document specifies requirements for three types of textile-reinforced thermoplastics hoses and hose assemblies of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements. They are suitable for use with: - oil-based

Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2020, Corrected version 2020-12); German version EN ISO 3949:2020

T/CECS 10114-2021 增强高密度聚乙烯（HDPE-IW）六棱结构壁管材

术语、定义和缩略语，材料，产品分类与标记，管材结构与连接方式，要求，试验方法，检验规则，标志、运输和贮存。

Reinforced high-density polyethylene (HDPE-IW) hexagonal structure wall pipe

NEMA TC 3-2021 与硬质PVC导管和管道一起使用的聚氯乙烯（PVC）配件

Polyvinyl Chloride (PVC) Fittings for Use with Rigid PVC Conduit and Tubing

DIN EN ISO 6259-2:2021 热塑性塑料管. 拉伸性能的测定. 第2部分: 未塑化聚氯乙烯(PVC-U),定向未塑化聚氯乙烯(PVC-O),氯化聚氯乙烯(PVC-C)和高强度聚氯乙烯(PVC-HI)制成的管材(ISO 6259-2-2020); 德文版本EN ISO 6259-2-2020

This part of ISO 6259 specifies a method of determining the tensile properties of pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI),

Thermoplastics pipes - Determination of tensile properties - Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chlorid

ASTM D2609-21 聚乙烯 (PE) 塑料管塑料插入配件的标准规格

1.1?This specification covers plastic insert fittings for polyethylene (PE) plastic pipe, and also PVC insert fittings for PE to PVC pipe transitions. Included are requirements for materials, workmanship, dimensions, and burst pressure. 1.2?The text of this specification refere

Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

ASTM D3035-21 基于受控外径的聚乙烯(PE)塑料管(DR-PR)标准规范

1.1?This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter IPS 1/2?to 3, for both non-pressure and pressure rated water (see Appendix X1). Included are requirements for polyethylene compounds and PE plastic pipe, a

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

ASME NM.1-2020 热塑性管道系统

Thermoplastic Piping Systems

DIN EN 13598-1:2020 用于非压力地下排水和污水处理的塑料管道系统. 未增塑的聚(氯乙烯)(PVC-U)、聚丙烯(PP)和聚乙烯(PE). 第1部分: 辅助配件和浅室规范; 德文版 EN 13598-1-2020

This document specifies the definitions and requirements for ancillary fittings and shallow chambers installed underground in non-pressure drainage and sewerage systems and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with minera

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings and shallow chambers; German version EN 13598

DIN EN 13598-2:2020 用于非压力地下排水和污水处理的塑料管道系统. 未增塑的聚(氯乙烯)(PVC-U)、聚丙烯(PP)和聚乙烯(PE). 第2部分: 人孔和检查室规范; 德文版 EN 13598-2-2020

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) manholes and inspection chambers intended for non-pressure underground drainage and sewerage systems to a maximum depth of 6 m from gr

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers; German version EN 13598-2:2020

DB1310/T 228-2020 地暖管用石墨烯改性耐热聚乙烯导热母粒技术规范

本文件适用于地暖管用石墨烯改性耐热聚乙烯导热母粒

Technical specifications for graphene-modified heat-resistant polyethylene thermal conductive masterbatch for floor heating pipes

T/CECS 10110-2020 排污、排水用高性能硬聚氯乙烯管材

规定了排污、排水用高性能硬聚氯乙烯管材（以下简称管材）的术语和定义，符号和缩略语，材料，产品分类及标记，要求，试验方法，检验规则，标志、运输和贮存。

High performance unplasticized poly（vinyl chloride）pipes for sewage and drainage

NB/T 10371-2019 煤矿抽放瓦斯用涂（覆）层加强筋螺旋焊接钢管性能检验规范

Specifications for performance inspection of spiral welded steel pipes with coated (coated) layer reinforcements for coal mine gas drainage