G39 胶粘剂 标准查询与下载

DIN EN 15286:2013 人造合成石. 墙体饰面用平板和瓷砖(内外墙壁); 德文版本EN 15286-2013

Agglomerated stone - Slabs and tiles for wall finishes (internal and external); German version EN 15286:2013

BS EN ISO 10545-9:2013 瓷砖. 耐热冲击的测定

Ceramic tiles. Determination of resistance to thermal shock

NF P61-203-1-1:2013 建筑工程 - 浮式找平层或平板下及固定瓷砖下绝热底漆的实施 - 第1-1部分: 技术标准条款合同单

Building works - Implementation of insulating undercoats under floating screed or slab and under fixed tiling - Part 1-1 : contract bill of technical model clauses

ISO 26842-1:2013 粘合剂.室内木制品用粘合剂评估和选择的测试方法.第1部分:非恶劣环境中抗分层性

This part of ISO 26842 gives guidelines to select, by means of delamination-resistance tests, adhesive/wood combinations in non-severe environments, in which the products are not exposed to extreme changes in temperature and humidity. A series of exposure cycles at various temperature and humidity values is provided to verify that the adhesive selected, or a product bonded with the adhesive, meets the necessary requirements for resistance to delamination. This part of ISO 26842 is intended to help the user not only to select a suitable adhesive, but also to evaluate adhesives and adhesively bonded wood products. NOTE When actual wood products are tested using this method, the test results might not be comparable because the test laboratory will not normally have had adequate control over the way the product was assembled. This part of ISO 26842 is not intended for use in the qualification of structural components.

Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 1: Resistance to delamination in non-severe environments

PD CEN/TS 14999:2013 热塑管道系统粘合剂.贮存容器加速老化测试

This Technical Specification describes a method for an accelerated ageing test of an adhesive in its container. The result provides the manufacturer with an indication of the storage stability of the adhesive and container combination and their ability to retain adhesive properties. The method described is intended for solvent based adhesives for thermoplastic piping systems but may be applied to other adhesive types if appropriate. The method described in this Technical Specification does not give a correlation between the results obtained after the accelerated ageing test and after the shelf life of the adhesive at the ambient conditions defined by the manufacturer in the data sheet. NOTE Some of the solvents used in adhesives applied for bonding pipe joints are highly flammable and may even cause explosion when heated (tetrahydrofurane). Therefore, the users of this standard need to take special precautions when testing such adhesives according to the provisions of this standard which require prolonged heating of the container with the adhesive.

Adhesives for thermoplastic piping systems - Accelerated ageing test in storage container

EN 302-4:2013 承重木结构用胶粘剂.试验方法.第4部分:承重情况下木结构的收缩测量

This European Standard specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions. It is suitable for the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425 and prEN 16254; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.). This method is not intended for use to provide numerical design data and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength

EN 1242:2013 粘合剂.异氰酸酯含量的测定

This European Standard specifies a method for the determination of the isocyanate content of adhesives, adhesive components and their basic constituents. It is not applicable to products containing blocked isocyanate groups which can be liberated by the reagents used in this test method.

Adhesives - Determination of isocyanate content

EN 13999-1:2013 胶粘剂.使用后低溶剂或无溶剂胶粘剂放射特性快速测量方法.第1部分:通用规程

This European Standard describes a conventional standard method for assessing potential emissions from adhesives after their application. This European Standard applies only to "solvent-free" and "low-solvent" adhesives as they are defined in EN 923:2005+A1:2008. The adhesives shall be applicable at room temperature.

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure

EN 13999-2:2013 胶粘剂.使用后低溶剂或无溶剂胶粘剂放射特性快速测量方法.第2部分:挥发性有机化合物的测定

This European Standard specifies a method for the determination of single volatile organic compounds (VOC) and of the total amount of volatile organic compounds (TVOCEN 13999) in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923:2005+A1:2008. The method is based on use of a solid sorbent with subsequent desorption and gas chromatographic analysis. The method is applicable to measurement of non-polar and slightly polar VOC.

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 2: Determination of volatile organic compounds

EN 16254:2013 粘合剂.承载木结构用乳剂聚合异氰酸盐(EPI).分类和性能要求

This European Standard establishes a classification for emulsion polymerised isocyanate (EPI) adhesives according to their suitability for use in load-bearing timber structures in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the industrial manufacture of load-bearing timber structures only. The performance requirements of this standard apply to the adhesive only, not to the structure. This European Standard is primarily intended for the use of adhesive manufacturers and for the use in timber structures bonded with adhesives, to assess or control the quality of adhesives. This European Standard only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions. Such an adhesive meeting the requirements of this European Standard for its type is adequate for use in a load-bearing timber structure, provided that the bonding process has been carried out according to an appropriate product standard.

Adhesives - Emulsion polymerized isocyanate (EPI) for load-bearing timber structures - Classification and performance requirements (Incorporates Amendment A1: 2016)

HG/T 4362-2012 水性干法纸塑复膜胶

本标准规定了水性干法复膜胶(以下简称复膜胶)的分类、技术要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于以涂布在塑料薄膜上,经烘干后覆盖在印刷品的表面,再经加热、加压处理,使塑料薄膜与印刷品粘合在一起,成为纸/塑合一成品的水性干法复膜胶。

Waterbased laminating adhesive used in paper with polymer films by heating process

HG/T 4363-2012 汽车车窗玻璃用单组份聚氨酯胶粘剂

本标准规定了汽车车窗玻璃用单组份聚氨酯胶粘剂的术语和定义、分类、标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于汽车前后风挡玻璃和侧窗玻璃粘接密封用单组份聚氨酯胶粘剂。

One-part polyurethane adhesive for automobile window

KS M ISO 9142:2012 粘合剂.胶粘连接试验用标准实验室老化条件的选择导则

이 표준은 접착 연결부가 여러 가지 환경 조건(기후적 또는 화학적)에 노출되어 물성에 미치

Adhesives－Guide to the selection of standard laboratory ageing conditions for testing bonded joints

KS M ISO 8510-2:2012 粘合剂.软硬粘结试样组件剥离试验.第2部分:180度剥离

이 표준은 특정 조건하에서 한 쪽이 연성 피착재이고, 다른 한 쪽이 강성 피착재로 접착된

Adhesives－Peel test for a flexible-bonded-to-rigid test specimen assembly－Part 2：180° peel

KS M ISO 8510-1:2012 粘合剂.软硬粘结试样组件剥离试验.第1部分:90度剥离

Adhesives-Peel test for a flexible-bonded-to-rigid test specimen assembly-Part 1:90 ° peel

NF P61-610/IN1:2012 磁砖胶粘剂 - 要求, 一致性评估, 分类和命名.

Adhesives for tiles - Requirements, evaluation of conformity, classification and designation.

ASTM D4689-12 酪蛋白型胶粘剂标准规格

1.1 This specification covers casein and other protein-blend adhesives for use adhering wood to wood. The adhesive type covered by this specification is a dry powder or granular product comprising a mixture of casein, or casein and other protein source, with the necessary dry chemicals to effect solution when the mixture is added to water. Note 1???Although the term casein adhesive is used throughout this specification, historically, the adhesive subclass described in 1.1 has been known as casein glue. See Terminology D907, adhesive types. 1.2 Limitations???Cooked casein adhesives are not covered by this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Sections 8 through 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive, Casein-Type

HG/T 4222-2011 热熔胶粘剂低温挠性试验方法

本标准规定了用芯轴弯曲法来测定热熔胶粘剂挠性方法。 本标准适用于薄片形式的热熔胶粘剂在低温条件下挠性的测定。也可通过调节试验环境装置和试样温度进行指定条件下的挠性试验。

The testing method of low temperature flexibility for hot melt adhesive

UL 2762-2011 粘合剂

Adhesives

LY/T 1601-2011 水基聚合物异氰酸酯木材胶黏剂

本标准规定了水基聚合物－异氰酸酯木材胶粘剂的术语和定义、分类、要求、试验方法、检验规则及包装、标志、运输和贮存等。 本标准适用于木材用水基聚合物－异氰酸酯胶粘剂。

Water based polymer-isocyanate adhesives for wood