G39 胶粘剂 标准查询与下载

DIN EN 15416-2:2008 苯酚和氨基塑料除外的负荷轴承木结构用粘结剂 试验方法 第2部分 压力剪切多重粘结样品的静载荷试验

This European Standard specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures. It is suitable for the following applications: a) for assessing the compliance of adhesives according to prEN 15425; b) for assessing the suitability and quality of adhesives for load-bearing timber structures. This test is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended for use to provide numerical design data and does not necessarily represent the performance of the bonded member in service. It is not applicable to assessment of the suitability of adhesives for the manufacture of wood-based panels.

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 2: Static load test of multiple bondline specimens in compression shear; English version of DIN EN 15416-2:2008-03

DIN EN 14814:2008 压力下流体用热塑性管道系统的粘合剂.规范

This European Standard specifies the functional requirements and test methods for adhesives used for joining the components of unplasticised poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile -butadiene-styrene (ABS) thermoplastic piping systems for fluids under pressure. It provides for the evaluation of conformity of the adhesive for this EN.

Adhesives for thermoplastic piping systems for fluids under pressure - Specifications; English version of DIN EN 14814:2008-03

DIN EN 15274:2008 结构组件用一般用途粘合剂.要求和试验方法

This European Standard specifies requirements for adhesives intended for use in the creation and general assembly of Icad-bearing, structural elements used in civil engineering works and the construction of buildings. Other than the exceptions stated, it embraces all combinations of bonded materials, used to create or repair Icad-bearing elements. It covers individual adhesives and special purpose kits comprising various combinations of adhesive types and components. It includes test methods and methods of assessment. The performance requirements in this standard may not be applicable to highly specialised applications in extreme environmental conditions, e.g. cryogenic use, nor do they cover specialised circumstances such as accidental impact, e.g. due to traffic or ice, or earthquake loading where specific performance requirements will apply. The intended use is for internal and external construction elements and those cladding and covering elements (excluding ceramic tiles) specifically required, by regulatory authorities, to provide protection from fire in identified building zones, including escape routes. It does not cover: Prefabricated, bonded structural components. Concrete bonded either to itself or steel or a material based on carbon fibre. Wood, when bonded to itself to form a timber based, laminated beam [of the type known as a 'Glulam' beam] intended for use as a major structural, Icad bearing element. Thermoplastics [e.g. polyethylene, polypropylene, polyamide and fluorinated polymers in general] unless they have been specifically prepared [usually through a specialised oxidative process] for bonded assembly on site. Co-axial metallic assemblies comprising fasteners- threaded and otherwise, pipes and tubes. Glass assemblies in structural glazing applications made using silicone adhesives. Those structural elements that are permanently immersed in water.

General purpose adhesives for structural assembly - Requirements and test methods; English version of DIN EN 15274:2008-01

DIN EN 15275:2008 结构粘合剂.土木工程和建筑结构中同轴金属组装件用厌氧胶特性

This European Standard specifies requirements and test methods for the characterisation of anaerobic adhesives intended for the general assembly of co-axial metallic elements in building and civil engineering structures including fasteners- threaded and otherwise, pipes and tubes. It is applicable to single adhesives and systems (kits) comprising adhesives, activators and/or primers for both internal and external construction elements. This European Standard only applies to metallic substrates.

Structural adhesives - Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures; English version of DIN EN 15275:2008-01

DIN 68141:2008 木材粘合剂.承载木材构件用木材粘合剂使用性能测定

Wood adhesives - Determination of properties of use of wood adhesives for load-bearing timber structures

ASTM E865-08 蜂窝夹层板用结构薄膜粘结剂的标准规范

1.1 This specification covers film adhesives for bonding of honeycomb sandwich panels. The adhesives are used for new production or depot repair. The adhesives shall be suitable for forming bonds that can withstand long exposures to temperatures from −55 to 93°C (−67 to 200°F) and also withstand the combinations of stress, temperature, and relative humidity expected to be encountered in service. The adhesives shall be used for bonding aluminum alloy facing to nonmetallic core, edge attachments, and other components of a sandwich panel. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Structural Film Adhesives for Honeycomb Sandwich Panels

ASTM D6736-08 乳胶漆耐磨性的标准试验方法

Interior flat paints may become burnished in areas where clothing or upholstered furniture rub against a wall. This rubbing may cause a smoother, glossier surface at the contacted area, depending on the level or type of pigments in the paint and binder hardness. This method permits a more quantitative estimate of burnish resistance than those using manual rubbing techniques.1.1 This test method covers a procedure for measuring the resistance of latex paints to burnishing under dry conditions. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Burnish Resistance of Latex Paints

ASTM E864-08 蜂窝状保护板中要用粘合剂粘结的铝合金板面制备的标准实施规程

Durable adhesive bonds to aluminum alloys can be obtained reliably only through proper selection and careful control of the materials used and the steps in the bonding process. The preparation of the aluminum alloys to obtain clean, uniform surfaces with appropriate characteristics is a critical step. This practice describes how such surfaces can be obtained.1.1 This practice covers the preparation of clean uniform surfaces of aluminum alloys suitable for formation of durable adhesive bonds to nonmetallic honeycomb materials in the manufacture of sandwich panels for tactical shelters. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see 5.2.1.

Standard Practice for Surface Preparation of Aluminum Alloys to be Adhesively Bonded in Honeycomb Shelter Panels

ASTM E1555-08 用于夹层板修补的结构膏胶粘剂标准规范

Adhesives used in the repair of sandwich panels for durable, rigidwall, relocatable structures must have a combination of mechanical property levels and environmental resistance that will ensure long-term durability of the adhesive bonds when exposed to severe climatic exposures. In addition, these adhesives must have processability characteristics that permit their use in a variety of repair scenarios and environments. This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures.1.1 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures. 1.1.1 This specification covers two-part epoxy adhesive suitable for bonding aluminum alloy facings to nonmetallic core, core to core, and core to perimeter aluminum extrusion frame in the repair of durable rigidwall relocatable structures. The adhesive shall be suitable for forming bonds that will withstand exposure to temperatures from −54 to 93°C (−65 to 199°F) and high relative humidity and will also withstand the combinations of stress, temperature, and relative humidity that are expected to be encountered in service. The adhesive shall also be suitable for the bonding of panel inserts and edge attachments. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given, or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Structural Paste Adhesive for Sandwich Panel Repair

ASTM E1800-08 粘结泡沫中心夹层面板(160℉,高湿设备)的胶粘剂的标准规范-一型面板

This specification is intended to provide information on the properties of adhesives, and the test methods required to evaluate adhesives to be used in the production bonding of aluminum alloys to foam core materials for the manufacture of tactical shelters. 1.1 This specification covers two-part paste adhesives for bonding foam core sandwich panels. The adhesive may be used for new production or depot maintenance. The adhesive should be suitable for forming bonds that can withstand long term exposure to temperatures from −55 to 71°C (−67 to 160°F) and also withstand combinations of stress, temperature, and humidity expected to be encountered in service. The adhesives shall be used for bonding aluminum alloy facing to foam core, inserts, internal aluminum framing members, and other components of a foam cored sandwich panel. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (160176;F Elevated Humidity Service), Type I Panels

ASTM D7447-08e1 标示粘合剂应用标准方法

An adhesive symbol provides an efficient means of placing complete information about adhesives on engineering drawings. The joint is the basis of reference for the symbol to which the arrow line is pointed. The reference line of the symbol is used to designate the type of adhesive to be used, including information about its physical form, chemical technology family, requirements for surface preparation, application method (bead versus roll coat), and cure method. The optional tail (shown at left in Fig. 1) provides a place to include additional information about the adhesive that is not referenced in other notations. Refer to Fig. 1 for an overview schematic of the adhesive symbol denoted by a mast supporting a circle with the letter “A” inside for adhesive. Detail behind each of the elements noted (for example, FORM, CHEM, APPL METH) can be found in corresponding tables in Section 5. FIG. 1 Standard Locations of Elements of the Adhesive Symbol1.1 This practice covers a standard symbol that may be used by the design-engineering community on engineering drawings to indicate a bonded assembly for any type of adhesive. 1.2 This design is based on criteria contained in ANSI/AWS A2.4 as well as ISO 15785. 1.3 The values given in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Symbolizing Adhesive Applications

ASTM E1794-08 用于粘结泡沫中心夹层面板(200℉,高湿设备)的胶粘剂的标准规范-二型面板

This specification is intended to provide information on the properties of adhesives, and the test methods required to evaluate adhesives to be used in the production bonding of aluminum alloys to foam core materials for the manufacture of tactical shelters.1.1 This specification covers two-part adhesives for bonding foam core sandwich panels. The adhesive may be used for new production or depot maintenance. The adhesive should be suitable for forming bonds that can withstand long-term exposure to temperatures from −55 to 93°C (−67 to 200°F) and also withstand combinations of stress, temperature, and humidity expected to be encountered in service. The adhesives shall be used for bonding aluminum alloy facing to foam core, inserts, internal aluminum framing members, and other components of a foam cored sandwich panel. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (200176;F Elevated Humidity Service), Type II Panels

ASTM D7374-08 端接合木材用胶粘剂高温性能评定的规程

End-jointed lumber studs used in fire resistance-rated assemblies shall be able to support the superimposed design load for the specified time under an elevated temperature exposure, when a wall assembly is exposed to a standard fire specified in Test Methods E 119. Light-weight wood assemblies utilize gypsum wallboard or other types of membrane protection to accomplish a requisite fire resistance rating for the assembly. However, wood studs and the end-joints in the studs shall resist the developed elevated temperature environment for the duration of the rating. This practice provides a method for evaluating the elevated temperature performance of an adhesive used in end-jointed lumber as compared with the elevated temperature performance of solid wood. 1.1 This standard practice is to be used to evaluate the elevated temperature performance of adhesives used in end-jointed lumber. 1.2 A symmetric wall assembly containing end-jointed lumber studs is exposed to a standard fire exposure specified in Test Methods E 119. 1.3 The wall assembly shall sustain the applied load during a standard fire exposure specified in Test Methods E 119 for a period of 60 min or more. 1.4 This practice is used to evaluate the performance of adhesives used in end-jointed lumber to heat and flame under controlled conditions, but it does not by itself incorporate all factors required for fire hazard or fire risk assessment under actual fire conditions. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed Lumber

BS EN 15416-3:2007+A1:2010 负荷轴承木结构用粘合剂.试验方法.带弯曲剪切载荷的试样在循环气候条件下的蠕变试验

This European standard specifies a method for determining the creep deformation of bonded specimens loaded in bending shear. It is applicable to adhesives used in load-bearing timber structures. It is suitable for the following applications: a) for assessing the compliance of adhesives to !EN 15425" Adhesives, One component polyurethane, for load bearing timber structures - Classification and performance requirements; b) for assessing the suitability and quality of adhesives for load-bearing timber structures. This test is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended to provide numerical design data and does not necessarily represent the performance of the bonded member in service. It is not applicable for assessing the suitability of adhesives for the manufacture of woodbased panels

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Creep deformation test at cyclic climate conditions with specimens loaded in bending shear

KS M 3701-2007 木材用尿素树脂胶粘剂

이 규격은 합판, 집성재, 파티클 보드, 일반 목공 등에 사용하는 액상 요소 수지 목재 접

Urea resin adhesives for wood

NF T76-335:2007 胶粘剂.用针-环试件测定厌氧胶粘剂的剪切强度

Adhesives - Determination of shear strength of anaerobic adhesives using pin-and-collar specimens.

ISO 29863:2007 自粘胶带.静态剪切附着力的测量

This European Standard specifies a series of methods for the determination of the ability of a pressure sensitive tape to remain adhered under a constant load applied parallel to the surfaces of the tape and substrate. The European Standard contains: - method A : Self adhesive tapes – Measurement of shear adhesion to a vertical standard steel panel; - method B : Self adhesive tapes – Measurement of shear adhesion to a vertical panel covered with NIST SRM 1810A 1) standard fibreboard; - method C : Self adhesive tapes – Measurement of shear adhesion to a vertical panel covered with a fibreboard agreed upon by the buyer and seller; - method D : Self adhesive tapes – Measurement of shear adhesion of filament reinforced tape applied to a horizontal standard steel panel; - method E : Self adhesive tapes – Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with NIST SRM 1810A 1) standard fibreboard; - method F : Self adhesive tapes – Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with a fibreboard agreed upon by the buyer and seller; - method G : Self adhesive tapes – Measurement of shear adhesion to a vertical standard steel panel at elevated temperature after a 10 min dwell time.

Self adhesive tapes - Measurement of static shear adhesion

ISO 29862:2007 自粘胶带.抗剥离粘接力特性的测定

This European Standard specifies a series of methods for the determination of peel adhesion properties of self adhesive tapes. Annexes A and B specify further variations in the testing protocol according to specific conditions. This European Standard contains: Method 1: Self adhesive tapes – Measurement of peel adhesion from stainless steel at an angle of 180° ; Method 2: Self adhesive tapes – Measurement of peel adhesion from its own backing at an angle of 180° ; Method 3: Self adhesive tapes – Measurement of peel adhesion of double sided and transfer tapes at an angle 180° ; Method 4: Self adhesive tapes – Measurement of adhesion of the liner to an adhesive tape at an angle of 180°. Together with Annex A Self adhesive tapes – Measurement of peel adhesion from a surface at low temperature ; Annex B Self adhesive tapes – Measurement of peel adhesion from a surface at an angle of 90°.

Self adhesive tapes - Determination of peel adhesion properties

ISO 29864:2007 自粘胶带.断裂强度和断裂伸长率的测量

This European Standard specifies methods to measure the breaking strength and elongation at break of a self adhesive tape when it is subjected to a tensile force sufficient to cause it to break. The breaking strength of adhesive tape is of value as an indication of its uniformity and quality, and its ability to withstand stresses during application and use. The elongation at break of the adhesive tape is of value as an indication of its uniformity and quality as well as a rough indication of its ability to conform to curved and irregular surfaces. It is usually determined at the same time as the breaking strength. This test method describes a procedure for testing 12 mm or 24 mm wide samples cut from supplied rolls of self adhesive tapes. Alternatively rolls of self adhesive tape up to 50 mm wide may be directly tested in their original width. In these circumstances the practical breaking strength and elongation will be typical of the manufacturer’s cut edges. When newly cut sample pieces are tested, because of the better cutting of the edges, the results can be higher than would be found on commercial tape.

Self adhesive tapes - Measurement of breaking strength and elongation at break

BS EN 15337:2007 粘合剂.用针-环试件测定厌氧胶粘剂的剪切强度

This European Standard specifies a method for the determination of the shear strength of anaerobic-curing liquid adhesives used for retaining cylindrical assemblies pin-and-collar type, or for locking and sealing threaded fasteners. This test method may also be used for other adhesives. The test is for ranking and quality control of adhesives. The result does not necessarily reflect the performance of the materials in service and the test is not suitable for providing numerical data for design purposes. NOTE Numerical design data may be obtained from tests using the materials and configurations used in the actual structure.

Adhesives - Determination of shear of anaerobic adhesives using pin-and-collar specimens