G42 胶管、胶带、胶布 标准查询与下载

T/CRIA 16008-2019 耐灼烧金属网芯输送带

1.范围 2.规范性引用文件 3.结构、 4标记、 5技术要求、 6试验方法、 7检验、 8标志、包装、贮存和运输。

Burn-resistant metal mesh conveyor belt

T/CRIA 16005-2018 输送带用对位芳纶长丝及线绳

本标准规定了输送带用对位芳纶长丝及线绳的术语和定义、分类和标识、技术要求、试验方法、检验规则和标志、包装、运输、贮存的要求。 本标准适用于输送带用对位芳纶长丝及线绳。 包含规范性引用文件，术语及定义，分类和标识，技术要求，试验方法，检验规范，标志，包装运输和储存等。

Para-aramid filament and cord for conveyor belt

HG/T 5460-2018 支撑坝用橡胶气囊

Rubber airbag for supporting dam

HG/T 5459～5462-2018 废旧轮胎裂解炭黑、支撑坝用橡胶气囊、硅酸乙酯偶联剂和脲基硅烷偶联剂（2018）

Waste tire pyrolysis carbon black, rubber airbags for supporting dams, ethyl silicate coupling agent and ureidosilane coupling agent (2018)

BS ISO 8789:2018 机动车辆运送石油液化气用橡胶软管和软管组件. 规范

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles. Specification

ISO 8789:2018 摩托车输送液化石油气用橡胶软管和软管组件. 规范

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification

DIN EN ISO 10619-1:2018 橡胶和塑料软管和管材.曲挠性和刚性的测量.第1部分:在环境温度下的弯曲试验(ISO 10619-1-2017); 德文版本 EN ISO 10619-1-2018

This International Standard specifies three methods for measuring the flexibility of a hose (Method A1, Method B and Method C1) where the deformation of the hose is measured and two methods for measuring stiffness (Method A2 and Method C2) by measuring the force to bend the hose when rubber or plastic hoses or tubing are bent to a specific radius at ambient temperature. Method A1 and A2 are suitable for hoses and tubing of internal diameter up to and including 80 mm. Method A1 allows the measurement of the flexibility of the hose by measuring the reduction in outside diameter when the hose is compressed between two plates. Method A2 provides a means of measuring the force required to reach a specific bend radius (stiffness), when the hose is compressed as between two plates. The test may be carried out at a specified internal pressure. Method B is suitable for hoses and tubing up to and including 100 mm and provides a means of assessing the behaviour of the hose when bent around a mandrel. The final mandrel diameter used may be taken as the minimum bend radius of the hose. As this value is determined by the reduction of the O.D which can be used as a measure of the flexibility of the hose. The hose being tested may be unpressurised, pressurised or under vacuum and if required with the curvature or against the curvature of the hose if such curvature is present. Method C1 and C2 are suitable for hose of 100 mm and above. Method C1 provides a means of determining the flexibility of the hose at the minimum bend radius. Method C2 provides a method of measuring the stiffness of the hose at the bend radius.

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 1: Bending tests at ambient temperature (ISO 10619-1:2017); German version EN ISO 10619-1:2018

ISO 21012:2018 低温容器.软管

This document specifies design, construction, type and production testing, and marking requirements for non-insulated cryogenic flexible hoses used for the transfer of cryogenic fluids within the following range of operating conditions: — working temperature: from −270 °C to +65 °C; — nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards. It is intended that the hose be designed and tested to satisfy the generally accepted rated pressure i.e. at least PR 40. Hoses may be then selected with a PR equal to or greater than the maximum allowable pressure (PS) of the equipment to which it is to be used.

Cryogenic vessels - Hoses

JIS K 6322:2018 传送带.纺织装置橡胶传送带规范

Conveyor belts -- Specification for rubber covered conveyor belts of textile construction

ISO 28017:2018 疏浚用金属或织物增强橡胶软管和软管总成规范

This document specifies requirements for two types, seven classes and three grades of wire- or textilereinforced dredging hoses with nominal sizes ranging from 100 to 1200. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperatures ranging from −10 °C to +40 °C. This document covers two types of hose, as follows: — type 1: floating type, for delivery only, which includes flotation material to give the hose buoyancy; — type 2: submarine type for delivery and suction. This document does not specify requirements concerning the service life of hoses or hose assemblies. Specifying such requirements is the responsibility of the customer, in consultation with the hose manufacturer.

Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification

JIS K 6348:2017 气体用橡胶管

Rubber tubes for gas

JIS K 6351:2017 气体用金属线增强橡胶软管和软管配件

Wire reinforced rubber hoses and hose assemblies for gas

ISO 10619-2:2017 橡胶,塑料软管和管材.曲挠性和刚性的测量.第2部分:低于环境温度的弯曲试验

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bending tests at sub-ambient temperatures

BS ISO 2321:2017 橡胶线.试验方法

Rubber threads. Methods of test

BS ISO 1436:2017 橡胶软管和软管组件.油质或水质流体用金属丝编织增强液压型管.规范

Rubber hoses and hose assemblies. Wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification

BS ISO 4079:2017 橡胶软管和软管组件.油质或水质流体用织物增强液压型管.规范

Rubber hoses and hose assemblies. Textile-reinforced hydraulic types for oil-based or water-based fluids. Specification

ISO 11237:2017 橡胶软管和软管组件.油基或水基流体用的金属丝编织增强压实型.规范

This document specifies requirements for five types of compact, wire-braid-reinforced hose and hose assembly of nominal size from 5 to 31,5. They are suitable for use with — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from 0 °C to +60 °C; — water at temperatures ranging from 0 °C to +60 °C. This document does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification

DIN EN ISO 6806:2017 油燃烧器软管和软管组件.规范(ISO 6806-2017);德文版本EN ISO 6806-2017

This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners. Two types of hose assembly are specified: Type 1 for flux and reflux, and type 2 for insertion between the oil burner pump and the atomizing connection.

Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017); German version EN ISO 6806:2017

ISO 2321:2017 橡胶线.试验方法

This document specifies methods of test for determining general physical and mechanical properties of rubber threads, as well as specific mechanical properties of such threads in contact with fabrics. Owing to the comparatively small cross-section and the unusual conditions of service of this material, certain special methods have been developed. Some of the tests included in this document are not entirely suitable for threads made from certain synthetic rubbers (e.g. urethane rubber). These tests are intended for natural or synthetic polyisoprene rubbers. Comparisons can only be made on new rubber threads or on those with identical processing histories. In the interpretation of results from threads which have been subjected to spooling, fabrication or any other process, the previous history is important, and what is known of this and of any relaxation treatments used is intended to be reported.

Rubber threads - Methods of test

ISO 3862:2017 橡胶软管和软管组件.油基或水基流体用橡胶包皮螺旋钢丝增强液压型.规范

Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification