G43 橡胶密封件 标准查询与下载

JIS B 2402-1:2013 组合弹性密封元件的旋转轴唇型密封件.第1部分:标称尺寸和公差

This Standard specifies nominal dimensions and tolerances of the rotary shaft lip-type seals with spring incorporating elastomeric sealing elements (hereafter referred to as “seals”) suitable for the range of shaft diameter from 6mm to 480 mm and the range of housing bore from 16 mm to 530 mm. Seals shall be used under the low-pressure condition of 0kPa to 30kPa in gauge pressure, and classified into six types according to the construction. Respective basic types are as given in figure 1. The seals without spring are shown in Annex JA.

Rotary shaft lip-type seals incorporating elastomeric sealing elements.Part 1: Nominal dimensions and tolerances

ANSI/ASTM E2750:2013 穿入密封圈用数据扩展指南

Guide for Extension of Data For Penetrations Seals

HG/T 4392-2012 汽车滤清器橡胶密封件

本标准规定了汽车滤清器橡胶密封件的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于汽车机油滤清器、燃油滤清器用橡胶密封件。本标准不适用于汽车空气滤清器密封件。

Rubber seals for automobile filter

BS ISO 16589-3:2011 含热塑性密封元件的旋转轴唇型密封件.储存、搬运和安装

Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Storage, handling and installation

BS ISO 16589-4:2011 含热塑性密封元件的旋转轴唇型密封件.性能试验程序

Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Performance test procedures

BS ISO 16589-5:2011 含热塑性密封元件的旋转轴唇型密封件.目视缺陷的标识

Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Identification of visual imperfections

BS ISO 16589-1:2011 含热塑性密封元件的旋转轴唇型密封件.公称尺寸和公差

Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Nominal dimensions and tolerances

JIS B 2401-4:2012 O型密封圈.第4部分:抗挤压密封圈(支撑密封圈)

This Standard specifies the back-up rings that are intended for preventing extrusion of O-rings specified in JIS B 2401-1. NOTE ：The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 3601-4-2008 Fluid power systems-O-rings-Part 4:Anti-ex-trusion rings (back-up rings) (MOD) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified),and NEQ (not equivalent) according to ISO/IEC Guide 21-1.

O-rings -- Part 4: Anti-extrusion rings (back-up rings)

JIS B 2401-3:2012 O型密封圈.第3部分:质量验收标准

O-rings -- Part 3: Quality acceptance criteria

JIS B 2401-2:2012 O型密封圈.第2部分:外壳尺寸规格

This Standard specifies the shapes and dimensions of housings for 0-rings used for general machinery applications (hereafter referred to as the "housings"), with or without back-up rings. The basic housing dimensions for ISO O-rings for general industrial applications(Series F)specified in ISO 3601-2 are given in Annex JA.

O-Rings -- Part 2: Housing dimensions and sizes

BS ISO 16589-2:2011 含热塑性密封元件的旋转轴唇型密封件.词汇

Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Vocabulary

ASTM C564-12 铸铁污水管及其配件用橡胶垫圈的标准规格

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

ANSI/AWWA C111/A21.11-2012 球墨铸铁压力管和配件用橡胶垫接头

This standard describes rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for potable water, wastewater and reclaimed water supply service.

Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings

HG/T 3096-2011 水闸橡胶密封件

本标准规定了水闸橡胶密封件和橡塑复合密封件的要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于水利、水电工程闸门用橡胶密封件和橡塑复合密封件（以下简称密封件）。

Rubber seals of water gate

DIN 7863-1:2011 用于窗户和包层的弹性体玻璃和面板垫片.技术交货条件.第1部分:无孔弹性体玻璃和面板垫片

Elastomor glazing and panel gaskets for windows and claddings - Technical delivery conditions - Part 1: Non celluar elastomer glazing and panel gaskets

ASTM F104-11 非金属衬垫材料标准分类系统

This classification system is intended to encourage uniformity in reporting properties; to provide a common language for communications between suppliers and consumers; to guide engineers and designers in the test methods commonly used for commercially available materials; and to be versatile enough to cover new materials and test methods as they are introduced. This system is based on the principle that nonmetallic gasket materials can be described in terms of specific physical and mechanical properties. This enables the user, or producer, to characterize a nonmetallic gasket based on properties that are important for the application.1.1 This classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork, cellulose, and other organic or inorganic materials in combination with various binders or impregnants are included. Materials normally classified as rubber compounds are not included, since they are covered in Classification D2000. Gasket coatings are not covered, since details thereof are intended to be given on engineering drawings or in separate specifications. Facing materials for laminate composite gasket materials (LCGM) are included in Classification System F104. Assembled LCGMs are covered in Classification F868. 1.2 Since all of the properties that contribute to gasket performance are not included, use of the classification system as a basis for selecting materials is limited. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Classification System for Nonmetallic Gasket Materials

ASTM C564-11 铸铁污水管及其配件用橡胶垫圈的标准规范

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard.

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

ASTM F2837-11 衬垫材料的热压特性的标准试验方法

The hot compression properties of a gasket material, including creep resistance and compression set, are a major factor with regard to the selection of a given material for use in a particular sealing application. The significance of the test method is based, in part; on the assumption that if a material exhibits too much creep at elevated temperature that it will no longer function as effectively as a seal. This assumption can only be used as a guide; however, since exact yield or failure points are difficult to define for gasket materials (which are usually viscoelastic in nature). Two or more materials can be compared to determine differences in their hot compression properties. A sample of material can be compared to an established standard or previously determined characteristics on original lots of the same material, for quality assurance purposes.1.1 This test method covers a means of measuring the hot compression properties of a gasket material by measuring its creep under a constant load at both room temperature and while increasing the temperature. Short term creep properties including both cold and hot creep, total creep and compression set of a gasket material can be determined. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hot Compression Properties of Gasket Materials

ASTM F2837-10 衬垫材料的热压特性的标准试验方法

The hot compression properties of a gasket material, including creep resistance and compression set, are a major factor with regard to the selection of a given material for use in a particular sealing application. The significance of the test method is based, in part; on the assumption that if a material exhibits too much creep at elevated temperature that it will no longer function as effectively as a seal. This assumption can only be used as a guide; however, since exact yield or failure points are difficult to define for gasket materials (which are usually viscoelastic in nature). Two or more materials can be compared to determine differences in their hot compression properties. A sample of material can be compared to an established standard or previously determined characteristics on original lots of the same material, for quality assurance purposes. Samples are to be tested with a raised profile insert or calibration ring described in 6.3 and Fig. 1 so that the area (2042 mm2 (3.17 in.2)) remains constant during the test. FIG. 1 Test Assembly for Determining Hot Compression1.1 This test method covers a means of measuring the hot compression properties of a gasket material by measuring its creep under a constant load at both room temperature and while increasing the temperature. Short term creep properties including both cold and hot creep, total creep and compression set of a gasket material can be determined. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hot Compression Properties of Gasket Materials

ANSI/ASTM F477:2010 塑料管连接用弹性体密封件(垫圈)规范

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe