G43 橡胶密封件 标准查询与下载

ASTM D3542-08 桥用预制聚氯丁(橡胶)弹性接头封缝件的标准规范

1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant adhesive and is designed to seal the joint and reject incompressibles. Note 18212;This specification may not be applicable for seals whose height is less than 90 % of its nominal width. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges

HG/T 3326-2007 采煤综合机械化设备橡胶密封件用胶料

本标准规定了采煤综合机械化设备用橡胶密封件胶料的要求、试验方法、检验规则及标志、标签、包装、贮存。 本标准规定的材料适用于制造采煤综合机械化设备中液压支架及单体支柱液压系统用橡胶密封件。

Rubber compound for coal-digger parts of comprehensive mechanization equipment

HG/T 3980-2007 汽车轴承用密封圈

本标准规定了汽车轴承用骨架式橡胶密封圈的要求、试验方法、检验规则及标志、包装、贮存和运输。 本标准适用于汽车轴承用骨架式橡胶密封圈。

Sealing rings of automobile bearing

SANS 974-2:2007 橡胶密封垫圈（非多孔性）．第二部分：用于乳品加工业的垫圈

Covers the requirements for five classes (based on hardness) of non-cellular vulcanized rubber joint rings for use in vessels and pipelines used for the storage and conveyance of dairy products.

Rubber joint rings (non-cellular) Part 2: Joint rings for use in the dairy industry

BS EN 62339-1:2007 表面安装流体分配部件用模块元部件接口.弹性密封件

This International Standard applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers. The scope of this standard is limited as follows. a) This standard addresses only surface-mount fluid distribution components and proper sealing methods. This standard is limited to sealing methods using elastomeric material for the seals. b) The designs of the actual system components and the flow substrate are not specified in this standard. Any indication of mounting direction or other indexing is left to the manufacturer as required for its equipment. c) Users shall be aware that, on the basis of the stream conditions of their processes, other technologies and components may be readily available. d) This standard does not address the effects of various stream conditions on the technical functionality of the component. e) This standard does not address maintenance concerns for the components. f) This standard does not refer to design issues pertaining to specific safety requirements. These issues should be referenced to other standards, organizations, and recommended guidelines. g) International, national, and local codes, regulations, and laws should be consulted to ensure that each component meets the user's regulatory requirements. The object of this standard is to establish properties and physical dimensions that define the interface for surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. The interface controls the dimensions and location of the sealing surfaces to allow change of just one element of the system without modification of the entire system. This is what makes the system modular from both a design and a maintenance standpoint.

Modular component interfaces for surface-mount fluid distribution components - Elastomeric seals

AWWA C111/A21.11-2006 韧性铁压力管和配件的橡胶垫接头

This standard describes rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for water supply service. 1. Mechanical joint. The mechanical joint is designed for pipe in sizes 3 in. through 24 in. (76 mm through 610 mm).* 2. Push-on joint. The push-on joint is designed for pipe and fittings in sizes 3 in. through 64 in. (76 mm through 1,600 mm). 3. Flanged joint. The flanged joint is designed for pipe and fittings in sizes 3 in. through 64 in. (76 mm through 1,600 mm). 4. Modifications to push-on and mechanical joints. Modifications to the designs shown in this standard, including but not limited to segmented or special glands and split sleeves, are permissible as long as the design meets the performance requirements stated in Sec. 4.7.

Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings

ASTM F477-07 连接塑料管用弹性密封件(垫圈)的标准规范

1.1 This specification covers elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications. This refers to push-on joints which require no internal or external pressure to effect the initial seal. 1.2 Requirements are given for natural or synthetic rubber gaskets, or a combination of both.Note 18212;Oil-resistant gaskets are available for those applications where exposure to solvents or oil may occur. The user should contact the gasket manufacturer for recommendations. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

HG/T 3880-2006 耐正负压内包骨架旋转轴 唇形密封圈

本标准规定了耐正、负压内包骨架旋转轴唇形密封圈（以下简称密封圈）的术语、定义、代号、型式以及要求、试验方法、标志、包装、运输和贮存。 本标准适用于安装在齿轮泵的旋转轴端，对液压油和润滑脂起密封作用的密封圈，密封圈的工作温度为-40℃～100 ℃，工作压力-56kPa～0.2MPa。

Pressure and vacuum resistant rubber covered rotary shaft lip seals

HG/T 3097-2006 橡胶密封件 110℃热水供应管道的管接口密封圈 材料规范

本标准规定了饮用和非饮用热水（达110 ℃）供应管道用的硫化橡胶密封圈的材料要求。 根据密封圈的类型、应用和一种特定密封圈的要求规定了几种不同的密封圈识别代码（见表3）。 本标准给出了成品管接头密封圈的通用要求。考虑到管接头的性能是随着密封圈的材料、密封圈的结构和管接头的设计而变化的，因此特殊应用所要求的任何附加要求在相关的产品标准中规定。如适用，本标准与规定管接头性能要求的产品标准一同使用。 本标准适用于铸铁管、钢管、陶瓷管、石棉水泥管、水泥管、钢筋水泥管、塑料管及玻璃纤维增强塑料管等所有管接口密封圈。 本标准适用于复合的或非复合的密封圈的弹性体部分。对于硬度范围在76IRHD～95IRHD 的材料制成的复合密封圈，只有当材料参与密封作用或有助于密封圈的长期稳定时才适用扯断伸长率、压缩永久变形及应用松弛要求。 本标准不适用于由多孔橡胶材料或闭孔材料作为其结构的一部分而制成的接口密封圈。

Rubber seals Jonit rings for pipelines for hot-water supply up to 110℃. Specification for the materials

ASTM D2000-06ae1 汽车用橡胶制品的标准分类系统

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.Note 18212;This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used.1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials.1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. Note 28212;When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits.1.4 The values stated in SI units are to be regarded as standard.

Standard Classification System for Rubber Products in Automotive Applications

ASTM D2000-06 汽车用橡胶制品的标准分类系统

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. Note 1This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used.1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials.1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. Note 2When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits.1.4 The values stated in SI units are to be regarded as standard.

Standard Classification System for Rubber Products in Automotive Applications

ASTM D2000-06a 汽车用橡胶制品的标准分类系统

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.Note 18212;This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used.1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials.1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence.Note 28212;When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits.1.4 The values stated in SI units are to be regarded as standard.

Standard Classification System for Rubber Products in Automotive Applications

ASTM C1115-06(2011) 密实弹性体硅橡胶衬垫和附件标准规范

This specification describes types (based on resistance to tearing and compression set), grades (based on durometer hardness), class (based on flame propagation requirements), and surfaces (based on surface characteristics) of products as listed in Section 4 for various applications. It is essential, therefore, that the applicable type, grade, class, and surface be specified, as well as other options stated, so that the proper product is provided for the intended use.1.1 This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building construction and also as components in structural silicone sealant glazing systems. 1.2 The following precautionary statement pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.4 The values stated in metric (SI) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information purposes only. 1.5 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories

ASTM C1166-06(2016) 密封和蜂窝弹性垫片和附件的火焰传播的标准测试方法

5.1 This test method is designed to differentiate the flame propagation characteristics of dense or cellular elastomeric compounds used in gaskets, setting blocks, shims, or spacers. It is a small scale test which enables the specifier to exercise engineering judgment in the selection of materials. 5.2 In this test method, the specimens are subjected to a specific laboratory fire test exposure condition. If different test conditions are substituted or the anticipated end-use conditions are changed, it may not be possible by or from this test method to predict changes in the performance characteristics. Therefore, the results are valid only for the fire test exposure condition described in this test method. 5.3 If the results obtained by this test method are to be considered in the total assessment of fire risk, then all pertinent established criteria for fire risk assessment developed by ASTM Committee E-5 must be included in the consideration. 1.1 This test method covers a laboratory procedure for determining flame propagation characteristics of a dense or cellular elastomeric gasket (such as expansion, lock-strip or compression gasket) or an accessory (such as a setting block, spacer or shim) when exposed to heat and flame, with no significance being attached to such matters as fuel contribution, rate of flame spread, smoke developed, or the nature and temperature of the products of combustion. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard assessment or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories

ASTM C1115-06 密实弹性硅橡胶衬垫和附件标准规范

1.1 This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building construction and also as components in structural silicone sealant glazing systems.1.2 The values stated in metric (SI) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information purposes only.1.3 Test Method C 1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.The following precautionary statement pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories

ASTM C1166-06(2011) 致密及多孔弹性体衬垫和附件火焰蔓延的标准试验方法

This test method is designed to differentiate the flame propagation characteristics of dense or cellular elastomeric compounds used in gaskets, setting blocks, shims, or spacers. It is a small scale test which enables the specifier to exercise engineering judgment in the selection of materials. In this test method, the specimens are subjected to a specific laboratory fire test exposure condition. If different test conditions are substituted or the anticipated end-use conditions are changed, it may not be possible by or from this test method to predict changes in the performance characteristics. Therefore, the results are valid only for the fire test exposure condition described in this test method. If the results obtained by this test method are to be considered in the total assessment of fire risk, then all pertinent established criteria for fire risk assessment developed by ASTM Committee E-5 must be included in the consideration.1.1 This test method covers a laboratory procedure for determining flame propagation characteristics of a dense or cellular elastomeric gasket (such as expansion, lock-strip or compression gasket) or an accessory (such as a setting block, spacer or shim) when exposed to heat and flame, with no significance being attached to such matters as fuel contribution, rate of flame spread, smoke developed, or the nature and temperature of the products of combustion. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard assessment or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories

ASTM F2524-06 用于运输的现场成形垫圈硅酮胶和密封剂的挥发物含量的测定的标准实施规程

1.1 This practice covers the quantitative determination of the volatile matter evolved during the curing process of silicone adhesives and sealants for transportation applications.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Volatile Content for Formed-in-Place Gaskets (FIPG) Silicone Adhesives and Sealants for Transportation Applications

HG/T 3784-2005 减压器唇形密封圈用橡胶材料

本标准规定了减压器唇形密封圈用橡胶材料的要求、试验方法及标识、包装、贮存。 本标准适用于汽车、摩托车减压器用唇形密封圈橡胶材料。

Rubber material for lip type seals in shock absorber

HG/T 2813-2005 软木橡胶密封制品 第二部分 机动车辆用

本部分规定了机动车辆用软木橡胶密封制品的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于汽车、拖拉机、铁路机车、摩托车等机动车辆在紧固力为2MPa～3MPa、使用温度在-40℃～+120℃下的静密封软木橡胶制品。

Cork-rubber sealing articles Part 2 Used for motor vehicle

HG/T 2812-2005 软木橡胶密封制品 第一部分 变压器及高压电器类用

本标准规定了油浸式变压器及高压电器类用软木橡胶密封制品的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于油浸式变压器和高压电器类及其配套组件用的软木橡胶密封制品。

Cork-rubber sealing articles Part 1 Used for transformer and electrical equipment of high voltage