共找到 546 条与 金属物理性能试验方法 相关的标准,共 37 页
Test methods for conductivity type of extrinsic semiconducting materials
Test method for silicon brick dimension—Laser technology method
Test method for particles on polished silicon wafer surfaces
本标准帘定了利用拉受光谱调斌N 型侯化儿衬底片载流子浓度的方法, 本标准适用于在蓝宝石.雄化奸、秆、氨化稼材料上生长的N 型氨化皖桂底片载流子波度的测试 测试范围:1X10" cm一1X102 cm-:。
Test method for carrier concentration of gallium nitride substrates—Raman spectrum method
Metallic and its compound powder—Determination of specific surface and particle size—Air permeating method
Sintered metal materials and hardmetals—Determination of electrical resistivity
Critical current measurement—DC critical current of Ag-and/or Ag alloy-sheathed Bi-2212 and Bi-2223 oxide superconductors
Electronic characteristic measurements—Surface resistance of superconductors at microwave frequencies
本标准规定了Cu/Nb-Ti复合超导线中铜-超[体积]比的测试方法。 本方法和附录A中提供的可选方法适用于截面积为0.1 mm~3 mm、Nb-Ti丝直径为2 μm~200 μm,铜-超[体积]比不小于0.5的Cu/Nb-Ti复合超导线。 本标准的Cu/Nb-Ti复合测试导体具有圆形或矩形截面的单一化结构。本标准采用硝酸溶解铜,给出了常规测试所允许的偏差和其他具体的限定。 截面积、丝直径和铜-超[体积]比超出本范围的Cu/Nb-Ti复合超导线,也可以使用本方法测量,但不确定度将降低。此外,特殊的情况下,对于超出规定范围的导体,测试样品可能存在特殊的几何形状,但为了简化及保持低不确定度,本标准不涉及此类问题。 经过适当的修正,本标准给出的测试方法可以应用于其他复合超导线。
Matrix to superconductor volume ratio measurement.Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires
Determination of whiteness for zinc oxide produced by direct process
Measurement method for X-ray double crystal diffraction rocking curve of sapphire crystals
Determination of thermal transmittance for architecture aluminium alloy thermal barrier profiles
Test method for determining the orientation of sapphire single crystal
Surface coating weight (thickness) of electrical steel—X-ray spectrometric method
Methods of measurement for amorphous and nanocrystalline alloys—Part 2: Lamination factor of amorphous alloy strips
Methods of test for the determination of coating insulation resistance and coating adhesion of electrical strip and sheet
Technical specification for testing of liquidus temperature of the electrolyte
GB/T8753 的本部分规定了铝及铝合金阳极氧化膜在酸性湾液中浸蚀后,按质量损失评定其封孔质量的方法。 本部分适用于在大气中暴露,以装饰和保护为目的,具备抗污染能力,可抵御环境腐蚀的阳极氧化障封孔质量的评定。 其中无硝酸预浸的酸漫蚀法适用于户内用途阳极氧化膜封孔质量的评定,硝酸预浸的酸浸蚀适用于户外用途阳极氧化膜封孔质量的评定。 当测试结果出现争议时,硝酸预浸的磷铬酸法可作为仲裁试验。 本部分不适用于下列工艺处理的阳极氧化膜,a)通常不进行封孔处理的硬质阳极氧化膜; b)在重铬酸盐溶液中圭孔处理过的阳极氧化膜c)在铬酸溶液中生成的阳极氧化膜; d)经朴水处理的阳极氧化膜。
Anodizing of aluminium and its alloys—Assessment of quality of sealed anodic oxidation coatings—Part 1:Measurement of the loss of mass after immersion in acid solution(s)
GB/T 19346的本部分规定了非晶纳米晶合金卷绕环形试样交流磁性能的测量方法。 本部分适用于测量各种变压器和电感类元器件以及磁屏蔽用的非晶纳米晶软磁合金在50 Hz ~ 200 kHz频率范围内的相对幅值磁导率、比总损耗、比视在功率等交流磁性能。如果有合适的经过校准的仪器,频率上限可延伸到1 MHz,但此时再现性应适当放宽要求。
Amorphous and nanocrystalline alloys measurement methods—Part 1:AC magnetic properties by the use of ring specimens
本标准规定了涡流法测试铜及铜合金导电率的方法原理、术语和定义、测试要求、操作方法和测试报告。 本标准适用于用涡流导电仪对不含铁磁性的铜及铜合金材料或产品进行导电率测试。
Electromagnetic (eddy-current) examination method for electrical conductivity of copper and copper alloys
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号