共找到 297 条与 其他钢铁产品 相关的标准,共 20 页
aubrittleoeent accelerated anviromenntal reurabílíty and wench torque teats of relf-lockin8 nuts.
Nut, Self-Locking Gang Channel, 100 Degree CSK, Floating, Low Height, Steel, 125 KSI Ftu, 450 Degrees F
本标准规定了采用邻菲罗啉光度法测定镁合金中铁含量的方法原理、试剂、仪器、分析步骤、分析结果的计算和允许差。 本标准适用于镁合金中铁含量的测定。 测定范围:0.001%~0.20%
Magnesium alloy chemical analysis method o-phenanthroline spectrophotometric determination of iron content
本标准规定了原子吸收光谱法测定镁合金中铁含量的方法原理、试剂、仪器、分析步骤、分析结果的计算和允许差。 本标准适用于镁合金中铁含量的测定。 测定范围:0.01%~0.20%
Methods of chemical analysis of magnesium alloys - Determination of iron content by atomic absorption spectrometry
Wire, Safety or Lock FSC 9505
Wire, Safety or Lock
Clevis, Rod, End-Adjustable and Plain, Steel FSC 5340
Clevis, Rod, End-Adjustable and Plain, Steel
이 규격은 사형 주강품의 기계 가공면 이외의 주물 표면의 겉모양 시험 방법 및 등급 분류에
Visual examination and classification of surface quality for steel castings
Purpose. The standard practices established in this document provide means of obtaining uniformity in the preparation and maintenance of National Aerospace Standards prepared in inch system of units and shall be adhered to insofar as practicable. For preparation and maintenance of metric unit documents see NASl0000.
NAS Documents Preparation and Maintenance in the Inch System of Units FSC CMAN; Revision 14
Grommet, PTFE-Split Revision 3; FSC 5325
Grommet, PTFE-Split Revision 3; FSC 5325
SEE PROCUREMENT SPECIFICATION, EXCEPT ALUMINUM ALLOY MATERIAL LIMITED TO 2014-T6 AND 2024T4 PER SPECIFICATIONS QQ-A-22514 TEMPER T6; QQ-A-20012 TEMPER T6; QQ-A-367, 2014-T6; QQ-A-20013 COND T4; QQ-A-22516 COND T4 AND QQ-A-25014 TEMPER T4
Fitting, Installation of Universal Elbow Rev 6
Caster, Light Duty, Rigid and Swivel Rev. 2
Caster, Light Duty, Rigid and Swivel Rev. 2
F3701X (FT15) powder metallurgy high-speed tool steel technical conditions
Technical delivery conditions for steel castings for pressure purposes; part 2: steel grades for use at ambient and elevated temperatures
Technical delivery conditions for steel castings for pressure purposes; part 3: steel grades for use at low temperatures
Technical delivery conditions for steel castings for pressure purposes; part 1: general
Technical delivery conditions for steel castings for pressure purposes; part 4: austenitic and austenitic-ferritic steel grades
This Korean Industrial Standard specifies the testing methods for clad steel 8 mm or over in full thickness whose base metal is steel and cladding metal is stainless steel or non-ferrous metal, hereafter referred to as the "clad steel", used for pressure vessel, boiler, nuclear reactor, storage tank, etc. Remark 1. The units and numerical values given in { } in this Standard are based on the Traditional System of Units and are appended for informative reference. 2. The relative standard of this standard is equal to attached list.
Testing methods for clad steel
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号