共找到 297 条与 其他钢铁产品 相关的标准,共 20 页
Flat products made of steels for pressure purposes; part 3: weldable fine grain steels, normalized
Zinc-Coated Steel Wire Strand General Instruction No 1
Zinc-Coated Steel Wire Strand General Instruction No 1
1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant adhesive and is designed to seal the joint and reject incompressibles.Note 18212;This specification may not be applicable for seals whose height is less than 90 % of its nominal width.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges
GRIP LENGTH IS FROM TOP Of BOLT HEAD TO END OF FULLCYLINDRICAL PORTION OF SHANK.
Bit, Six Lobe Drive - Internal Recess - for Power and Hand Tools Revision 1
All surfaces to be finished after fabrication.
Tee, Reducer, Flareless Tube to Swivel Swivel on Side (Rev. 2)
This specification defines the minlmum requirements and test conditions for cargo unlt load devices to be Installed in ctrl flcated aircraft and covers. pallets. nets and containers intended for use w i t h the followlnq classes of aircraft loading and restraint systems.
Cargo Unit Load Devices - Specification for Rev. 10
Prezentul standard stabile?te condi?iile tehnice generale de calitate ale articolelor de menaj ?i decorative din por?elan obi?nuit, sub form? de piese separate sau care compun servicii complete.
Porcelain household and ornamental goods. General technical requirements for quality
THIS ILLUSTRATION OF THE HANDLE IS FOR IDENTIFICATION PURPOSES ONLY AND IS N M INTENDED TO RESTRICT DESIGNS AND SHAPES MI101 WILL OTHERIJISE CONFORM TO SPECIFICATION REQUIREMENTS AND ARE WITHIN THE ENVELOPE DIMENSIONS.
Pin, Quick Release, Self-Retaining, Positive Locking, Single Acting,
SEE PROOJREMENT SPECIFICATION, NA0161 PINS SHALL BE FREE OF BURRS WITH ALL SHARP CORNERS ROUNDED
Pin, Quick Release, Self-Retaining, Positive Locking, Single Acting,
THIS ILLUSTRATION OF THE HANDLE IS FOR IDENTIFICATION PURPOSES ONLY AND IS N M INTENDED TO RESTRICT DESIGNS AND SHAPES MI101 WILL OTHERIJISE CONFORM TO SPECIFICATION REQUIREMENTS AND ARE WITHIN THE ENVELOPE DIMENSIONS.
Pin, Quick Release, Self-Retaining, Positive Locking, Single Acting,"T" Handle, Metric
THE FAILURE OF RAYS OF LIGHT COMING FROM ONE POINT THROUGH A LENS OR REFLECTING FROM A MIRROR, TO CONVERGE TO ONE FOCUS.
Pin, Quick Release, Positive Locking Single Acting, Metric Procurement Specification for
Determination of iron content in magnesium alloy
This standard' defines the general scope of Contractor managed and conducted development flight testing required on airborne systems procured by the military . The objectives of these tests are f o r the Contractor to develop the structura i n t e g r i t y and the performance and operational capabil I t I e s o f his product t o the point t h a t he I s s a t I s f I e d that the product meets the specification requirements and I s ready f o r Formal M I 1 I t a r y Eva1 uat ion.
Contractor Flight Development
This specification provides a standard for the manufacture; performance, inspection, and procurement of a numerical ly controlled wire harness manufacturing machine. This standard l i s t s minimum requirements and i s not intended t o 1 i m i t design advances.
Wire Harness Assembly Machine, Computerized Numerical Control
Scope- This specification establishes the requirements for nondestructive inspection (NDI), NDI standards, NDI methods, and NDI acceptance criteria.
Nondestructive Inspection of Advanced Composite Structures
DASH hWEZ.9 DESICKAT3 BORE DW'SEK INSIXE3 THSOF INCh. KOEWER SUFFIX TO DASH NUKjE.? DECIGNATES ALLOY STXZl MATZRIAL AND PRZPACKD WITW E0L-G-3276 G W E . Em? "8" SWFFMED SASE NUMBE.9 DESSISNATSS b4CC MATERIAL AND PREFACED WITH MIL&-25013 CREASE FOX 450'F OPL'TION.
Clip, Turnbuckle Locking Cancelled - March 1980 [Use: DLA MS21256 REV G ADMIN NOTICE 1, DLA MS21256 REV G ADMIN NOTICE 1, DLA MS21256 REV G, DLA MS21256 REV G, DLA MS21256 REV F, DLA MS21256 REV F, DLA MS21256 REV E, DLA MS21256 REV E, DLA MS212
This International Standard specifies, in conjunction with IS0 9002, the quality system requirements for the production and, when relevant, installation and servicing of medical devices.
Galvanized Steel Twisted Wire
This standard includes toolholder nose design parameters, pertinent geometries and a glossary of terms. This nose configuration with applicable drive system is referred to as a toolholder basic.
Toolholder, Nose Configuration - Machine Tools
この規格は,プラストクリー=ソグ,ピーニソグ,ェッチソグその他に用いる鋳鉄又は鋳鋼製のショット及びグリット(以下,ショット及びグリットという。)の粒度について規定する。
Cast shot and grit
This specification provides a standard for the manufacture, performance, reliability, inspection, and procurement of a series of Direct Numerical Confxol Systems. This standard lists minimum requirements and is not to limit design advances.
Direct Numerical Control System
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号