H68 贵金属及其合金 标准查询与下载

ASTM B563-01(2011) 钯银铜电气插头合金的标准规格

1.1 This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy

ASTM B476-01(2012) 锻制贵金属电接触材料标准规格

For purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with Practice E29. PropertyUnitRounded Unit for Observed or Calculated Value Chemical compositionpercent Hardness Knoop (100-g load unless other- wise specified) Vicker (specify load) Rockwell (all scales, specify which) Rockwell superficial (all scales, specify which) nearest unit on the last right hand place of figure of specified limit Resistivity μΩ·cm Tensile strength psi (MPa)nearest 1000 psi (nearest 10 MPa) Yield Strength psi (MPa)nearest 1000 psi (nearest 10 MPa) Elongation Below 5 % percentnearest multiple of 0.5 % 5 % and over percentnearest 1 % Grain size Up to 0.055 mm incl. mmnearest multiple of 0.005 mm Over 0.055 to 0.160, mm, incl. mmnearest 0.01 mm1.1 This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. Unless otherwise specified in the purchase order or in an individual specification, these general requirements shall apply to wrought electrical contact materials where indicated in the applicable product specifications issued by ASTM. 1.2 In case of conflict, the requirements on the purchase order, the individual specification, and this general specification shall prevail in the sequence named. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport ......

Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials

ASTM B541-01(2012) 电接触用金合金标准规格

1.1 This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Gold Electrical Contact Alloy

ASTM B541-01 电接触用金合金标准规范

1.1 This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units may be approximate. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Gold Electrical Contact Alloy

ASTM B563-01(2006) 电接触用钯银铜合金标准规范

1.1 This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy

ASTM B563-01(2017) 电接触用钯银铜合金的标准规格

1.1 This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy

ASTM B522-01(2017) 电接触用金银铂合金的标准规格

1.1 This specification covers 698201;% gold, 258201;% silver, 68201;% platinum alloy tubing, rod, wire, and sheet material for sliding electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Gold-Silver-Platinum Electrical Contact Alloy

ASTM B563-01 电接触用钯银铜合金标准规范

1.1 This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy

ANSI/ASTM B476:2001 锻压贵重金属一般要求规范

This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. Unless otherwise specified in the purchase order or in an individual specification, these general requirements shall apply to wrought electrical contact materials where indicated in the applicable product specifications issued by ASTM. In case of conflict, the requirements on the purchase order, the individual specification, and this general specification shall prevail in the sequence named. The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Specification for General Requirements for Wrought Precious Metal

ASTM B683-01(2006) 纯钯电接触材料标准规范

1.1 This specification covers palladium in the form of rod, wire, strip, and sheet material for electrical contacts.1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Pure Palladium Electrical Contact Material

DIN EN ISO 11426:1999 金和金珠宝合金的测定.火吹法(火试验法)

The document specifies a cupellation method (fire assay) for the determination of gold in gold jewellery alloys. Preferably the gold content of the alloys lies between 333 and 999 parts per thousand gold. The procedure applies specifically to gold alloys incorporating silver, copper and zinc. Some modifications are indicated where nickel and/or palladium are present in the socalled white gold alloys, as well for alloys containing 990 or more parts per thousand of gold.

Determination of gold in gold jewellery alloys - Cupellation method (fire assay) (ISO 11426:1997); German version EN ISO 11426:1998

BS EN ISO 11426:1999 金合金首饰中金含量的测定.灰吹法(火试验法)

Intended as the referee method for the determination of fineness in alloys covered by BS 29202.

Determination of gold in gold jewellery alloys - Cupellation method (fire assay)

ANSI/ASTM B589:1999 精炼钯规范

This specification covers refined palladium as sponge, cast bar, and wrought forms (Note 1) in one grade as follows:Grade 99.95 (UNS PO3995) -Palladium having a purity of 99.95 %. Note 1 -Other forms of unfabricated palladium of commerce are not to be excluded under this specification. Note 2 -For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E 29. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Specification for Refined Palladium

ANSI/ASTM B561:1999 精炼铂规范

This specification covers refined platinum as sponge, cast bar, and wrought forms (Note 1) in two grades as follows: Grade 99.95 (UNS PO4995) -Platinum having a purity of 99.95 %, min, and Grade 99.99 -Platinum having a purity of 99.99 % min. Note 1 -Other forms of unfabricated platinum of commerce are not to be excluded under this specification. Note 2 -For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the limiting value, in accordance with the rounding off method of Practice E 29. The values stated in inch-pound units are to be regarded as the standard. SI units are provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Specification for Refined Platinum

ANSI/ASTM B671:1999 精炼铱规范

This specification covers refined iridium as sponge and powder in two grades as follows: Grade 99.80 (UNS PO6100) - Iridium having a purity of 99.80 %. Grade 99.90 - Iridium having a purity of 99.90 %. Note 1 -For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E 29. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Specification for Refined Iridium

HB 5219.20-1998 镁合金化学分析方法 原子吸收光谱分析法测定银含量

本标准规定了采用原子吸收光谱法测定镁合金中银含量的方法原理、试剂、仪器、分析步骤、分析结果的计算和允许差。 　　本标准适用于镁合金中银含量的测定。 　　测定范围：0.50％～1.50％

Methods of chemical analysis of magnesium alloys - Determination of silver content by atomic absorption spectrometry

YS/T 408-1998 贵金属器皿制品

Utensils finished products of precious metals

ASTM B679-98(2004)e1 工程用钯的电沉积覆层标准规范

1.1 Purity -This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal. 1.2 Properties -Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The hardness range of electrodeposited palladium compares favorably with the other electroplated noble metals and their alloys. 1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only. 1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use

ASTM B844-98(2010) 银锡氧化触点材料的标准指南

The methods for manufacture (proprietary or otherwise) of these materials vary significantly among suppliers, and these methods influence such properties as arc erosion, contact resistance, and tendency to weld in service. Since the performance of contacts in a device depends on numerous factors outside the contact itself (opening speed, closing speed, contact pressure, contact bounce, environmental variations, assembly technique and variations, etc.) this guide cannot ensure performance control in the application. As part of the qualification on initial samples it is recommended that the user electrically test the materials in a functional manner for all devices applicable to the material''s use. This guide will provide a means for the contact manufacturer and contact user to reach agreement on the details of material to be supplied for a specific use and how to provide reasonable assurance that future lots will be similar in properties and microstructure to the initial test of sample contacts supplied.1.1 This standard provides guidelines for users and manufacturers of silver-tin oxide material produced in strip, rod, wire, and part form for electrical contact applications. 1.2 Silver-tin oxide refers to contact material containing silver, tin oxide, and other metal oxide which may be used for either improving the processing or performance of the material. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Guide for Silver-Tin Oxide Contact Material

ASTM B679-98 工程用钯的电沉积覆层标准规范

1.1 Purity -This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal. 1.2 Properties -Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The hardness range of electrodeposited palladium compares favorably with the other electroplated noble metals and their alloys. 1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only. 1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use