共找到 521 条与 通用零部件综合 相关的标准,共 35 页
이 규격은 플라스틱과 고무의 사출 금형에서 주로 사용하는 스프루 풀러에 대하여 규정한다.
Tools for moulding-Sprue pullers
이 규격은 사출 금형을 주문하거나 의뢰할 때 사용하는 규격과 설명에 대하여 규정한다.
Tools for moulding-Tool specification sheet for injection moulds
이 규격은 주축에 고정하기 위하여 테이퍼 구멍 또는 암나사를 가지는 다목적의 키형 연동 드
Key type three-jaw drill chucks-Specification
이 규격은 원통형 섕크를 갖는 공구용 콜릿과 그에 대응되는 홀더 및 너트의 치수, 재료 및
Collets for tool holders with taper ratio 1:10-Collets, holders, nuts
이 규격은 선반, 드릴링 머신, 밀링 머신 및 연삭기 등 공작 기계에 적용되는 플랜지 접촉
Hollow taper interface with flange contact surface-Part 1:Shanks-Dimensions
이 규격은 원통형 섕크를 갖는 공구용 콜릿과 그 대응되는 홀더 및 너트의 치수, 재료, 제
Collets with 8° setting angle for tool shanks-Collets, nuts and fitting dimensions
이 규격은 테이퍼 구멍 또는 암나사 장착부를 갖는 키 없는 연동 자동 조임형 드릴척(이하
Keyless type three-jaw drill chucks-Specification
이 규격은 원통형이나 모스 테이퍼형 섕크를 갖는 고속도강으로 제작된 2홈 트위스트 드릴의
High-speed steel two-flute twist drills-Technical specifications
이 규격은 KS B ISO 12164-1에 따른 홀로 테이퍼 섕크에 대응하여 테이퍼와 플랜
Hollow taper interface with flange contact surface-Part 2:Receivers-Dimensions
이 규격은 상용 순수 알루미늄(Al)으로 된 리벳 몸체와 알루미늄 합금(AlA)으로 된 맨
Closed end blind rivets with break pull mandrel and protruding head-AI/AIA
이 규격은 강(St)으로 된 리벳 몸체와 강(St)으로 된 맨드릴을 가지며, 호칭 지름 d
Closed end blind rivets with break pull mandrel and protruding head-St/St
이 규격은 굽힘성이 있는 가스 공급 라인에 사용되는 최대 설계 사용 압력 1 MPa과 2
Gas welding equipment-Thermoplastic hoses for welding and allied processes
이 규격은 아세틸렌 가스 용기의 충전시 검사에 대한 최소 요건을 규정한다. 이들 요건은 현
Cylinders for dissolved acetylene-Inspection at time of filling
이 규격은 기계의 상태 감시와 진단에서 사용되는 용어의 정의에 대하여 규정한다.
Condition monitoring and diagnostics of machines-Vocabulary
이 규격은 속도-면적법으로 개수로에서 유량 측정을 함에 있어 전체 오차의 개개 요인들 에
Liquid flow measurement in open channels-Velocity-area methods-Collection and processing of data for determination of errors in measurement
이 규격은 조석 운동의 영향을 받는 자연 하천 혹은 인공 하천에서 부유사 측정과 유사 이
Hydrometric determinations-Measurement of suspended sediment transport in tidal channels
이 규격은 조립핀과 관의 세트를 이용, 손목시계의 케이스에 쇠줄이나 가죽줄을 체결하는 전반
Timekeeping instruments-Wristwatch-cases-Fixing dimensions of non-spring-bar types
이 규격은 원통 인벌류트 기어 이의 대응 치면에 관한 정밀도 방식을 규정하고 있다. 또 기
Cylindrical gears-ISO system of accuracy-Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
이 규격은 인벌류트 원통 기어 이의 양 치면(齒面) 상호 물림 정밀도에 관하여 규정한다.
Cylindrical gears-ISO system of accuracy-Part 2:Definitions and allowable values of deviations relevant to radial composite deviations and runout information
이 규격은 18 mm 및 26 mm 크기의 5포트 공기압 방향 제어 밸브를 최대 정격 압력
Pneumatic fluid power-Five-port directional control valves,sizes 18 mm and 26 mm-Part 1:Mounting interface surfaces without electrical connector
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号