J12 滑动轴承 标准查询与下载

BS ISO 3547-7:2007 滑动轴承.卷制轴衬.薄壁轴衬壁厚的测量

This part of ISO 3547 describes, following ISO 12301, the checking methods and measuring equipment used for measuring the total wall thickness of thin-walled bushes in the finished state. NOTE All dimensions in this International Standard are given in millimetres.

Plain bearings. Wrapped bushes. Measurement of wall thickness of thin-walled bushes

BS ISO 12301:2007 滑动轴承.几何特性和材料质量特性的质量控制技术和检验

This International Standard specifies quality control techniques and inspection of the geometrical and material quality characteristics of the following types of plain bearings: -- thin-walled half-bearings with or without flange, as specified in ISO 3548; -- metallic thick-walled half-bearings (with and without flange) that are manufactured as halves but that are necessarily interchangeable and have the ratio s3 : Do > 0,11; -- wrapped bushes, as specified in ISO 3547; -- unsplit metallic bushes (with and without flange) made from solid and multilayer materials and with outside diameters up to 230 mm; -- solid polymer bushes (with and without flange) with inside diameters up to 200 mm; -- ring-type thrust washers and pressed bimetallic half-thrust washers, as specified in ISO 6525 and ISO 6526, respectively; -- bushes made from sintered material, as specified in ISO 2795.

Plain bearings. Quality control techniques and inspection of geometrical and material quality characteristics

BS ISO 3547-5:2007 滑动轴承.卷制轴衬.外径检验

This part of ISO 3547 specifies, following ISO 12301, the checking of the outside diameter of wrapped bushes (ISO 3547-2:2006, methods A, B and D) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the oversize between the outside diameter of the bush and the housing bore. For this reason, checking of the outside diameter of wrapped bushes can only be carried out under a constraining load by use of specialized measuring equipment. NOTE 1 The dimensions and tolerances of wrapped bushes are given in ISO 3547-1. Checking the wall thickness is the subject of ISO 3547-7.

Plain bearings. Wrapped bushes. Checking the outside diameter

BS ISO 3547-6:2007 滑动轴承.卷制轴衬.内径检验

The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes (see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the interference between the outside diameter of the bush and the housing bore. NOTE 1 All dimensions in this part of ISO 3547 are given in millimetres except where otherwise noted/designated. NOTE 2 The dimensions and tolerances of wrapped bushes are given in ISO 3547-1. NOTE 3 Checking of the wall thickness is the subject of ISO 3547-7. NOTE 4 Checking of the outside diameter of wrapped bushes is the subject of ISO 3547-5. 2

Plain bearings. Wrapped bushes. Checking the inside diameter

BS ISO 6281:2007 滑动轴承.试验设备内流体动力和混合润滑条件下的测试

This International Standard establishes guidelines for the testing of lubricated plain journal bearings in test rigs, running under conditions of hydrodynamic or mixed lubrication, during bearing and/or material development. It deals with both static and dynamic loading in solid and multi-layer journal bearings. It is not applicable to the testing of dynamic characteristics of lubricant film in journal bearings applied in calculation of vibration and stability of turbo-rotors. Further details of test procedures will need to be established when carrying out testing based on these guidelines.

Plain bearings. Testing under conditions of hydrodynamic and mixed lubrication in test rigs

KS B ISO 11687-2:2007 滑动轴承.滑动轴承座.第2部分:单边法兰式

이 규격은 축에 대한 설계 특성과 함께 사이즈 범위 9~28에 이르는 사이드 플랜지 베어링

Plain bearings-Pedestal plain bearings-Part 2:Side flange bearings

KS B ISO 7146:2007 滑动轴承.损坏和外观变化的原因、性质和术语

이 규격은 유체윤활 미끄럼 베어링 및 저널의 사용 중에 발생하는 외관상의 손상과 변화에 관

Plain bearings-Terms, characteristics and causes of damage and changes in appearance

KS B ISO 11687-3:2007 滑动轴承.滑动轴承座.第3部分:中心法兰式

이 규격은 축에 대한 설계 특성과 함께 사이즈 범위 9∼28까지의 센터 플랜지 베어링에 대

Plain bearings-Pedestal plain bearings-Part 3:Centre flange bearings

KS B ISO 7904-2:2007 滑动轴承符号.第2部分:应用

이 규격은 미끄럼 베어링의 계산, 설계 및 실험에 관하여 KS B ISO 7904-1에서

Plain bearings-Symbols-Part 2:Applications

KS B ISO 7905-1:2007 滑动轴承.轴承疲劳强度.第1部分:在液体润滑条件下应用试验台的滑动轴承

이 규격은 피로로 이어지는 베어링층의 응력을 평가함으로써 시험 결과 비교 가능성을 개선하는

Plain bearings－Bearing fatigue－Part 1：Plain bearings in test rigs and in applications under conditions of hydrodynamic lubrication

KS B ISO 7905-2:2007 滑动轴承.轴承疲劳强度.第2部分:金属轴程材料的液体样品的试验

이 규격은 강재 백메탈이 부착되지 않은 베어링 재료의 내구 피로 한도를 결정하는 시험방법에

Plain bearings－Bearing fatigue－Part 2：Test with a cylindrical specimen of a metallic bearing material

KS B ISO 7905-3:2007 滑动轴承.轴承疲劳强度.第3部分:金属复合轴承材料制平条的检验

이 규격은 다층 베어링 재료의 평면 스트립의 피로에서 내구 한도를 결정하기 위한 방법에 대

Plain bearings－Bearing fatigue－Part 3：Test on plain strips of a metallic multilayer bearing material

KS B ISO 7905-4:2007 滑动轴承.轴承疲劳强度.第4部分:金属复合轴承材料制轴承套的检验

이 규격은 다층 베어링 재료로 된 분할 베어링의 피로에 있어 그 내구 한도를 정하기 위한

Plain bearings－Bearing fatigue－Part 4：Tests on half-bearings of a metallic multilayer bearing material

KS B ISO 11687-1:2007 滑动轴承.滑动轴承座.第1部分:支撑式

이 규격은 축에 대한 설계 특성과 함께 사이즈 범위 9∼28 그리고 35∼71에 이르는 필

Plain bearings-Pedestal plain bearings-Part 1:Pillow blocks

ISO 3547-6:2007 滑动轴承.卷制轴衬.第6部分:内径检验

The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes (see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the interference between the outside diameter of the bush and the housing bore. NOTE 1 All dimensions in this part of ISO 3547 are given in millimetres except where otherwise noted/designated. NOTE 2 The dimensions and tolerances of wrapped bushes are given in ISO 3547-1. NOTE 3 Checking of the wall thickness is the subject of ISO 3547-7. NOTE 4 Checking of the outside diameter of wrapped bushes is the subject of ISO 3547-5. 2

Plain bearings - Wrapped bushes - Part 6: Checking the inside diameter

ISO 3547-5:2007 滑动轴承.卷制轴衬.第5部分:外径检验

This part of ISO 3547 specifies, following ISO 12301, the checking of the outside diameter of wrapped bushes (ISO 3547-2:2006, methods A, B and D) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the oversize between the outside diameter of the bush and the housing bore. For this reason, checking of the outside diameter of wrapped bushes can only be carried out under a constraining load by use of specialized measuring equipment. NOTE 1 The dimensions and tolerances of wrapped bushes are given in ISO 3547-1. Checking the wall thickness is the subject of ISO 3547-7.

Plain bearings - Wrapped bushes - Part 5: Checking the outside diameter

ISO 3547-7:2007 滑动轴承.卷制轴衬.第7部分:薄壁轴衬壁厚的测量

This part of ISO 3547 describes, following ISO 12301, the checking methods and measuring equipment used for measuring the total wall thickness of thin-walled bushes in the finished state. NOTE All dimensions in this International Standard are given in millimetres.

Plain bearings - Wrapped bushes - Part 7: Measurement of wall thickness of thin-walled bushes

ISO 12301:2007 滑动轴承.几何和材料质量特征的质量控制技术和检验

This International Standard specifies quality control techniques and inspection of the geometrical and material quality characteristics of the following types of plain bearings: -- thin-walled half-bearings with or without flange, as specified in ISO 3548; -- metallic thick-walled half-bearings (with and without flange) that are manufactured as halves but that are necessarily interchangeable and have the ratio s3 : Do > 0,11; -- wrapped bushes, as specified in ISO 3547; -- unsplit metallic bushes (with and without flange) made from solid and multilayer materials and with outside diameters up to 230 mm; -- solid polymer bushes (with and without flange) with inside diameters up to 200 mm; -- ring-type thrust washers and pressed bimetallic half-thrust washers, as specified in ISO 6525 and ISO 6526, respectively; -- bushes made from sintered material, as specified in ISO 2795.

Plain bearings - Quality control techniques and inspection of geometrical and material quality characteristics

KS B ISO 7904-1:2007 滑动轴承符号.第1部分:基本符号

이 규격은 미끄럼 베어링 분야에서 사용되고 있는 기본적인 기호에 대하여 규정한다.

Plain bearings-Symbols-Part 1:Basic symbols

KS B ISO 7902-3:2007 稳定运行中流体动力径向滑动轴承.圆柱体轴承.第3部分:可允许的运行参数值

이 규격은 실험상 허용 가능한 hlim, Tlim 및 lim p 의 수치에 대하여 규정한다

Hydrodynamic plain journal bearings under steady-state conditions－Circular cylindrical bearings－Part 3：Permissible operational parameters