J32 锻压 标准查询与下载

JB/T 11760-2013 直齿锥齿轮精密冷锻件 技术条件

本标准规定了齿部为冷精密锻造成形的直齿锥齿轮锻件(以下简称“冷锻件”)的要求、试验方法、检验规则,以及包装、搬运、贮存和标志等方面的要求。本标准适用于在压力机上,齿部最终采用精密冷锻工艺成形的直齿锥齿轮锻件,其端面模数≤10 mm,齿部直径≤180 mm的锻件。

Technical requirements on precision cold forging of straight bevel gear

JB/T 9179.7-2013 液压机上钢质自由锻件机械加工余量与公差 第7部分:筒体类

JB/T 9179的本部分规定了在液压机上自由锻筒体类(含有台阶筒体)钢质自由锻件的余量与公差。本部分适用于最终经芯棒拔长工序完工的筒体类(含台阶筒体)钢质自由锻件。

Machining allowances and tolerances of open die forgings on hydraulic press.Part 7: Cylinder

JB/T 9179.2-2013 液压机上钢质自由锻件机械加工余量与公差 第2部分:圆轴、方轴和矩形截面类

JB/T 9179的本部分规定了在液压机上自由锻圆轴、方轴和矩形截面类钢质自由锻件的机械加工余量与公差。本部分适用于长度大于等于直径、方截面边长和矩形截面长边的圆轴、方轴和矩形截面类钢质自由锻件。对于对称多边形轴类钢质自由锻件的机械加工余量与公差可按本部分规定参照执行。

Machining allowances and tolerances of open die forgings on hydraulic press.Part 2: Round shaft, square shaft and rectangular cross-section

JB/T 9179.3-2013 液压机上钢质自由锻件机械加工余量与公差 第3部分:台阶轴类

JB/T 9179的本部分规定了液压机上自由锻台阶轴类钢质自由锻件的余量与公差。本部分适用于截面为圆形、方形和矩形的各类台阶轴类钢质自由锻件。

Machining allowances and tolerances of open die forgings on hydraulic press.Part 3: Stepped shaft

JB/T 9179.1-2013 液压机上钢质自由锻件机械加工余量与公差 第1部分:一般要求

JB/T 9179的本部分规定了液压机上钢质自由锻件机械加工余量与公差的一般要求。本部分适用于在液压机上用自由锻方式锻造的钢质自由锻件。本部分规定的机械加工余量与公差适用于单件或小批量规模生产的钢质自由锻件。

Machining allowances and tolerances of open die forgings on hydraulic press.Part 1: General requirements

JB/T 9179.4-2013 液压机上钢质自由锻件机械加工余量与公差 第4部分:圆盘和冲孔类

JB/T 9179的本部分规定了在液压机上自由锻圆盘和冲孔类钢质自由锻件的余量与公差。本部分适用于零件高度(或厚度)小于零件直径的不带孔圆盘钢质自由锻件,以及零件内孔小于二分之一零件直径或矩形短边的冲孔类钢质自由锻件。对于带盲孔的圆盘类(或矩形类)钢质自由锻件可按本部分规定参照执行。

Machining allowances and tolerances of open die forgings on hydraulic press.Part 4: Disk and punched hole

JB/T 9175.2-2013 精密冲裁件 第2部分:质量

JB/T 9175的本部分规定了金属强力压边精密冲裁(以下简称精冲)件的质量。本部分适用于采用强力压边精冲方法生产的金属精冲件。

Fine blanked parts.Part 2: Quality

JB/T 9175.1-2013 精密冲裁件 第1部分:结构工艺性

JB/T 9175的本部分规定了金属强力压边精密冲裁(以下简称精冲)件的结构工艺性。本部分适用于采用强力压边精冲方法生产的金属精冲件。

Fine blanked parts.Part 1: Structural processability

ISO 9448-6:2013 冲压工具. 导套. 第6部分: E型, 法兰滑动导套, 1型

This part of ISO 9448 specifies the main dimensions and tolerances, in millimetres, of guide bushes of form E, flanged gliding bushes, type 1, intended for use in press tools and to be mounted in the clamp plate with transition fit and fixed to the plate by means of guide clamps. It gives guidance on the materials, and specifies the hardness and the designation of bushes in accordance with this part of ISO 9448.

Tools for pressing.Guide bushes.Part 6: Form E, gliding bushes, flanged, type 1

ISO 9182-2:2013 冲压工具.导柱.第2部分:A型、直导柱

This part of ISO 9182 specifies the dimensions and tolerances, in millimetres, of guide pillars, type A,intended for use in press tools. These guide pillars can be straight, type A1 (see Figure 1), or straight with end-locking and locking ring, type A2 (see Figure 2). It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this part of ISO 9182.

Tools for pressing.Guide pillars.Part 2: Type A, straight pillars

ISO 9448-9:2013 冲压工具.导套.第9部分:B型、直滚珠导套、2型

This part of ISO 9448 specifies the main dimensions and tolerances, in millimetres, of guide bushes of form B, plain ball cage bushes, type 2, intended for use in press tools and to be mounted in the clamp plate by means of interference fit. It gives guidance on the materials, and specifies the hardness and the designation of bushes in accordance with this part of ISO 9448.

Tools for pressing.Guide bushes.Part 9: Form B, ball cage bushes, plain, type 2

ISO 9448-2:2013 冲压工具.导套.第2部分:A型、直滑动导套、1型

This part of ISO 9448 specifies the main dimensions and tolerances, in millimetres, of guide bushes of form A, plain gliding bushes, type 1, intended for use in press tools and to be mounted in the clamp plate by means of interference fit. It gives guidance on the materials, and specifies the hardness and the designation of bushes in accordance with this part of ISO 9448.

Tools for pressing.Guide bushes.Part 2: Form A, gliding bushes, plain, type 1

ISO 9448-7:2013 冲压工具. 导套. 第7部分: F型, 法兰滚珠导套, 1型

This part of ISO 9448 specifies the main dimensions and tolerances, in millimetres, of guide bushes of form F, flanged ball cage bushes, type 1, intended for use in press tools and to be mounted in the clamp plate with transition fit and fixed to the plate by means of guide clamps. It gives guidance on the materials, and specifies the hardness and the designation of bushes in accordance with this part of ISO 9448.

Tools for pressing.Guide bushes.Part 7: Form F, ball cage bushes, flanged, type 1

ASME FORGING A NEW NUCLEAR SAFETY CONSTRUCT-2013 锻造新的核安全建设. 研讨会摘要

Forging a New Nuclear Safety Construct - WORKSHOP SUMMARY

ASTM A105/A105M-13 管系部件用碳钢锻件标准规格

1.1 This specification2 covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems. Included are flanges, fittings, valves, and similar parts ordered either to dimensions specified by the purchaser or to dimensional standards such as the MSS, ASME, and API specifications referenced in Section 2. Forgings made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. Larger forgings may be ordered to Specification A266/A266M. Tubesheets and hollow cylindrical forgings for pressure vessel shells are not included within the scope of this specification. Although this specification covers some piping components machined from rolled bar and seamless tubular products (see 5.2), it does not cover raw material produced in these product forms. 1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.3 Specification A266/A266M covers other steel forgings and Specifications A675/A675M and A696 cover other steel bars. 1.4 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”

Standard Specification for Carbon Steel Forgings for Piping Applications

ASTM A668/A668M-13 一般工业用碳素钢和合金钢锻件的标准规格

1.1 This specification covers untreated and heat-treated carbon and alloy steel forgings for general industrial use. Other ASTM specifications for forgings are available for specific applications such as pressure vessels, railroad use, turbine generators, gearing, and others involving special temperature requirements. 1.2 Hot-rolled or cold finished bars are not within the scope of this specification. 1.3 Six classes of carbon steel and seven classes of alloy steel forgings are listed (see Section 7), which indicates their required heat treatments, as well as mechanical properties. 1.4 Provision, with the suffix H for certification and marking, for the supply of forgings after hardness testing only. 1.5 Supplementary requirements, including those in Specification A788/A788M, of an optional nature are provided. These shall apply only when specified by the purchaser. 1.6 Appendix X1 lists the current classes corresponding to the various classes of Specifications A235, A237, and A243, which have been superseded by this specification. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard; within the text and tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.8 Unless the order specifies the applicable "M" specification, the forgings shall be furnished to the inch-pound units.

Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

ASTM A705/A705M-13 时效硬化的不锈和耐热钢锻件标准规格

1.1 This specification2 covers age-hardening stainless steel forgings for general use. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. Note 1—Bar products are covered by Specification A564/A564M.

Standard Specification for Age-Hardening Stainless Steel Forgings

ASTM A668/A668M-13e1 一般工业用碳素钢和合金钢锻件标准规格

1.1 This specification covers untreated and heat-treated carbon and alloy steel forgings for general industrial use. Other ASTM specifications for forgings are available for specific applications such as pressure vessels, railroad use, turbine generators, gearing, and others involving special temperature requirements. 1.2 Hot-rolled or cold finished bars are not within the scope of this specification. 1.3 Six classes of carbon steel and seven classes of alloy steel forgings are listed (see Section 7), which indicates their required heat treatments, as well as mechanical properties. 1.4 Provision, with the suffix H for certification and marking, for the supply of forgings after hardness testing only. 1.5 Supplementary requirements, including those in Specification A788/A788M, of an optional nature are provided. These shall apply only when specified by the purchaser. 1.6 Appendix X1 lists the current classes corresponding to the various classes of Specifications A235, A237, and A243, which have been superseded by this specification. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard; within the text and tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.8 Unless the order specifies the applicable "M" specification, the forgings shall be furnished to the inch-pound units.

Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

ASTM B381-13 钛和钛合金锻件标准规格

1.1 This specification2 covers 39 grades of annealed titanium and titanium alloy forgings as follows: 1.1.1 Grade F-1—UNS R50250. Unalloyed titanium, 1.1.2 Grade F-2—UNS R50400. Unalloyed titanium, 1.1.2.1 Grade F-2H—UNS R50400. Unalloyed titanium (Grade 2 with 58 ksi (400 MPa) minimum UTS), 1.1.3 Grade F-3—UNS R50550. Unalloyed titanium, 1.1.4 Grade F-4—UNS R50700. Unalloyed titanium, 1.1.5 Grade F-5—UNS R56400. Titanium alloy (68201;% aluminum, 48201;% vanadium), 1.1.6 Grade F-6—UNS R54520. Titanium alloy (58201;% aluminum, 2.58201;% tin), 1.1.7 Grade F-7—UNS R52400. Unalloyed titanium plus 0.12 to 0.258201;% palladium, 1.1.7.1 Grade F-7H—UNS R52400. Unalloyed titanium plus 0.12 to 0.258201;% palladium (Grade 7 with 58 ksi (400 MPa) minimum UTS), 1.1.8 Grade F-9—UNS R56320. Titanium alloy (38201;% aluminum, 2.58201;% vanadium), 1.1.9 Grade F-11—UNS R52250. Unalloyed titanium plus 0.12 to 0.258201;% palladium, 1.1.10 Grade F-12—UNS R53400. Titanium alloy (0.38201;% molybdenum, 0.88201;% nickel), 1.1.11 Grade F-13—UNS R53413. Titanium alloy (0.58201;% nickel, 0.058201;% ruthenium), 1.1.12 Grade F-14—UNS R53414. Titanium alloy (0.58201;% nickel, 0.058201;% ruthenium), 1.1.13 Grade F-15—UNS R53415. Titanium alloy (0.58201;% nickel, 0.058201;% ruthenium), 1.1.14 Grade F-16—UNS R52402. Unalloyed titanium plus 0.04 to 0.088201;% palladium, 1.1.14.1 Grade F-16H—UNS R52402. Unalloyed titanium plus 0.04 to 0.088201;% palladium (Grade 16 with 58 ksi (400 MPa) minimum UTS), 1.1.15 Grade F-17—UNS R52252. Unalloyed titanium plus 0.04 to 0.088201;% palladium, 1.1.16 Grade F-18—UNS R56322. Titanium alloy (38201;% aluminum, 2.58201;% vanadium) plus 0.048201;% to 0.088201;% palladium, 1.1.17 Grade F-19—UNS R58640. Titanium alloy (38201;% aluminum, 88201;% vanadium, 68201;% chromium, 48201;% zirconium, 48201;% molybdenum),

Standard Specification for Titanium and Titanium Alloy Forgings

SL 576-2012 水工金属结构铸锻件通用技术条件

本标准规定了水工金属结构设备常用的铸钢件、灰铸铁件和钢锻件(统称铸锻件)的技术要求、试验方法、检验规则及标志、包装、运输与贮存要求等。本标准适用于水工金属结构设备常用铸钢件、灰铸铁件和钢锻件(以下简称锻件)的设计、制造、验收等。

Specifications for castings and forgings of hydraulic steel structure