J65 木工机床及机用工具 标准查询与下载
共找到 881 条与 木工机床及机用工具 相关的标准，共 59 页
This document deals with all significant hazards,hazardous situations and events as listed in Clause 4 which are relevant to circular saw benches/up-cutting cross-cut sawing machines,hereinafter referred to as "machines",designed to cut solid wood,chipboard,fibreboard,plywood and also these materials if (where) they are covered with plastic edging and/or plastic/light alloy laminates when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.Circular sawing machines.Part 5: Circular sawbenches/up-cutting cross-cut sawing machines; German version EN 1870-5:2002+A2:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to double mitre sawing machines for V-cutting with a maximum cutting capacity (width and height) of < =200 mm,fitted or not with pneumatic systems,hereinafter referred to as the machine,designed to cut solid wood, chipboard,fibreboard or plywood and also these materials where they are covered with plastic laminate or edgings,when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.Circular sawing machines.Part 16: Double mitre sawing machines for V cutting; German version EN 1870-16:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard specifies all significant hazards,hazardous situation and events as listed in Clause 4,relevant to stationary and displaceable manual horizontal cutting cross-cut circular sawing machines with one saw unit (manual radial arm saws),hereinafter referred to as "machines",designed to cut solid wood, chipboard,fibreboard,plywood and also these materials if they are covered with plastic edging and/or plastic laminates,when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.Circular sawing machines.Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws); German version EN 1870-17:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable single spindle hand fed/integrated fed routing machines with fixed head but allowing only movement along the axis of the tool during machining hereinafter referred to as "machines" designed to cut solid wood, chip board,fibreboard,plywood and also these materials if they are covered with plastic laminate,edgings or veneer when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.One side moulding machines with rotating tool.Part 2: Single spindle hand fed/integrated fed routing machines; German version EN 848-2:2007+A2:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard specifies all significant hazards,hazardous situations and events as listed in Clause 4, which are relevant to NC boring machines,NC routing machines and NC combined boring/routing machines (as defined in 3.1) herein after referred to as "machines" designed to cut solid wood,chip board,fibreboard,plywood and also these materials where these are covered with plastic/light alloy laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.One side moulding machines with rotating tools.Part 3: Numerically controlled (NC) boring and routing machines; German version EN 848-3:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard is applicable to woodworking machines with cutting tools and/or sanding tools as defined in 3.2.1,when they are used as intended and under the conditions foreseen by the manufacturer.
Safety of woodworking machines.Part 1: Common requirements; German version EN 691-1:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard deals with all significant hazards,hazardous situations and events as listed in Clause 4 which are relevant to single blade circular log sawing machines with saw blade diameter > =600 mm and with integrated feed table with manual loading and/or unloading, (hereinafter referred to as machines),designed to cut solid wood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. This European Standard is not applicable to machines manufactured before the date of its publication as EN.
Safety of woodworking machines.Circular sawing machines.Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading; German version EN 1870-7:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard specifies all requirements and/or measures to reduce the hazards and limit the risks on multi-blade cross-cut sawing machines (with minimum two saw unit) with integrated feed of the work-piece and manual loading and/or unloading fitted with a saw blade drive motor for each saw unit,hereinafter referred to as "machines",designed to cut solid wood,chipboard,fibreboard, plywood and also these materials where they are covered with plastic edging and/or plastic/light alloy laminates,when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Safety of woodworking machines.Circular sawing machines.Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading; German version EN 1870-15:2012
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013-01
- 实施
This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit) and building site saws, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials, if they are covered with plastic edging and/or plastic/light alloy laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to cut wood-based material may also be used for cutting hardened plastic materials with similar physical characteristics as wood. NOTE 1 For the definition of stationary and displaceable machine see 3.2.9 and 3.2.10. NOTE 2 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving. Building site saws are used for ripping, cross cutting and dimensioning. The requirements of this document apply also to machines designed for grooving with a width not exceeding 20 mm in one pass by using a milling tool. This document does not apply to: a) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down; b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting. NOTE 3 Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-1:2012; a hand-held motor-operated electric tool and a saw bench to form an integrated whole are covered by EN 60745-1:2009 together with EN 60745-2-5: 2010. For the purpose of this document, building site saws having a tiltable spindle are considered to be circular saw
Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013
- 实施
- 2013-11
This European Standard specifies all hazards arising from the use of clamping devices for the fastening of milling tools and circular saw blades on woodworking machines and specifies the methods for the elimination or reduction of these hazards by the design of the clamping device and by the provision of information. This European Standard does not apply to arbors for spindle moulding machines in accordance with EN 848-1 or to clamping flanges for circular sawing blades to be used on circular sawing machines in accordance with the standard series EN 1870 and does not cover hazard related to the connection of the clamping device with the machine. Bore mounted tools which are mounted on an interchangeable arbor should be considered as a shank mounted tool. NOTE For definition of "woodworking machines", see EN 847-1.
Tools for woodworking - Safety requirements - Part 3: Clamping devices
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013
- 实施
- 2013
This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to semi-automatic horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws), hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials when covered with plastic edging and/or plastic/light alloy laminates when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for working rigid plastic materials with similar physical characteristics as wood. Any work-piece positioning equipment fitted to the machine is included in this European Standard. This European Standard does not apply to machines: a) with manual feed of the saw unit; or b) for cross cutting logs; or c) specifically designed for sawing and/or milling roof timber frames; or d) fitted with hydraulic braking systems. NOTE 1 Radial arm saws with manual feed of the saw unit (the saw unit is moved by hand) are dealt with in EN 1870-17:2012 and EN 61029-2-2:2009. NOTE 2 The requirements of this European Standard apply to all machines whatever their method of control, e. g. electromechanical and/or electronic. This European Standard is not applicable to machines which are manufactured before the date of its publication as EN. NOTE 3 Machines covered by this European Standard are listed under of Annex IV of the Machinery Directive.
Safety of woodworking machines - Circular sawing machines - Part 11: Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2013
- 实施
- 2013
Safety of woodworking machines. One side moulding machines with rotating tool. Numerically controlled (NC) boring and routing machines
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-30
- 实施
- 2012-11-30
Safety of woodworking machines. Common requirements
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-30
- 实施
- 2012-11-30
Woodworking machines - Double-end tenoning machines - Nomenclature and acceptance conditions
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-17
Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: single spindle vertical moulding machines
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-30
Woodworking machines - Double edging precision circular sawing machines - Nomenclature and acceptance conditions
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-17
Woodworking machines - Radial circular saws - Nomenclature and acceptance conditions
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-17
Woodworking machines - Single blade stroke circular sawing machines for lengthwise cutting of solid woods and panels - Nomenclature and acceptance conditions
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-17
Woodworking machines - Multi-spindle boring machines - Nomenclature
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
- 2012-11-17
Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: single spindle hand fed/integrated fed routing machines
- ICS
- 79.120.10
- CCS
- J65
- 发布
- 2012-11-01
- 实施
