K10 电工材料和通用零件综合 标准查询与下载

SANS 1411-6:2008 绝缘电缆和软电线用材料．第6部分：铠装

Specifies requirements for three types of metal armour materials that are components of insulated electric cables and that provide protection against mechanical damage both during installation of cables and in service.

Materials of insulated electric cables and flexible cords Part 6: Armour

IEC 61788-6:2008 超导体.第6部分:机械性能测量.铜/铌-钛复合超导体的室温拉伸试验

This part of IEC 61788 covers a test method detailing the tensile test procedures to be carried out on Cu/Nb-Ti superconductive composite wires at room temperature. This test is used to measure modulus of elasticity, 0,2 % proof strength of the composite due to yielding of the copper component, and tensile strength. The value for percentage elongation after fracture and the second type of 0,2 % proof strength due to yielding of the Nb-Ti component serves only as a reference (see Clauses A.1 and A.2). The sample covered by this test procedure has a round or rectangular cross-section with an area of 0,15 mm2 to 2 mm2 and a copper to superconductor volume ratio of 1,0 to 8,0 and without the insulating coating.

Superconductivity - Part 6: Mechanical properties measurement - Room temperature tensile test of Cu/Nb-Ti composite superconductors

ANSI/UL 6A-2008 电器用刚性金属导管.铝、青铜及不锈钢(草案到期5-9-08)

Proposed new trinational edition with the addition of requirements for Mexico and Canada. Requirements cover aluminum, stainless steel, and red brass electrical rigid metal conduit, elbows, couplings, and nipples for use as a metal raceway for installation of wires and cables in accordance with the CEC, NEC and NOM-001-SEDE.

Electrical Rigid Metal Conduit - Aluminum, Red Brass, and Stainless Steel (Proposal dated 5-9-08)

SN/T 0232.1-2007 进出口电线电缆检验规程.第1部分:通用要求

SN/T 0232的本部分规定了进出口电线电缆的通用要求、检验及判定。 本部分适用于塑料、橡皮或纸作绝缘，用退火铜线、无镀层铝线或铝合金线作导体的电线电缆，如：电气装备用电线电缆、电力电缆、通信电缆等。绕组线、裸电线部分适用。 本部分不适用于光缆。

Rules for the inspection of cable and wire for import and export.Part1:General requirements

JIS H 7313:2007 超导性.成批高温超导体的测量.大粒氧化物超导体的陷波流量密度

この規格は，バルク高温超電導体の捕そく(捉)磁束密度を測定するための試験方法について規定する。なお，この規格は，試料温度が4.2 Kから90 Kまでの範囲における捕そく（捉）磁束密度の測定に適用する。

Superconductivity -- Measurements for bulk high temperature superconductors -- Trapped flux density of large grain oxide superconductors

KS C 6111-4-2007 超高频带中大面积高温超导薄膜的表面电阻均匀性

이 규격은 유전체 공진기 측정법을 이용한 대면적 초전도체 박막의 고주파 표면저항의 균일성을

Homogeneity in the surface resistance of large high-Tc superconductor films at microwave frequencies

DIN EN 50423 Bb.1:2007 大于AC 1kV且小于等于AC 45kV的架空电力线.补充件1:德国的一般要求和标准情况(NNA)

Overhead electrical lines exceeding AC 1 kV up to and including AC 45 kV - Supplement 1: General requirements and Normative Aspects for Germany (NNA)

BS EN 61788-4:2007 超导性.剩余电阻率的测量.Nb-Ti复合超导电体的剩余电阻率

This part of IEC 61788 covers a test method for the determination of the residual resistance ratio (RRR) of a composite superconductor comprised of Nb-Ti filaments and Cu, Cu-Ni or Cu/Cu-Ni matrix. This method is intended for use with superconductors that have a monolithic structure with rectangular or round cross-section, RRR less than 350, and cross-sectional area less than 3 mm2. All measurements are done without an applied magnetic field. The method described in the body of this standard is the “reference” method and optional acquisition methods are outlined in Clause A.4.

Superconductivity - Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti composite superconductors

SANS 6138:2007 电缆和电线的耐火焰蔓延性能．单一垂直绝缘电缆或电线

Specifies a method for the determination of the resistance to flame propagation of single vertical insulated cable or cord.

Resistance of cables and cords to flame propagation - Single vertical insulated cable or cord

DIN EN 61788-2:2007 超导性.第2部分:临界温度测量.铌(指数3)-锡复合超导体的临界直流电流

Superconductivity - Part 2: Critical current measurement - DC critical current of Nb₃Sn composite superconductors (IEC 61788-2:2006); German version EN 61788-2:2007

DIN EN 61788-1:2007 超导性.第1部分:临界温度测量.铜/铌-钛复合超导体的直流临界电流(IEC 61788-1:2006)

Superconductivity - Part 1: Critical current measurement - DC critical current of Nb-Ti composite superconductors (IEC 61788-1:2006); German version EN 61788-1:2007

DIN 49073:2007 符合DIN 49445、DIN 49447 和DIN EN 60309-2 (VDE 0623-20)要求金属制仪表盒、16A250V以下装修辅助仪器用沉入安装的绝缘材料和插座引出线.主要尺寸

Metal boxes and boxes of insulating material for recessed mounting for accomodation of accessories up to 16 A 250 V and socket-outlets according to DIN 49445, DIN 49447 and DIN EN 60309-2 (VDE 0623-20) up to 32 A 690 V - Main dimensions

UL 514B-2007 导管、管道和电缆配件

1.1 These requirements cover FITTINGS for use with cable and conduit intended for installation in accordance with the National Electrical Code, ANSI/NFPA 70, the Canadian Electrical Code (CEC), Part I, CSA C22.1, and the Standard for Electrical Installations, NOM-001-SEDE. 1.2 These requirements cover CONDUIT LOCKNUTS, conduit BUSHINGS, metal stud BUSHINGS, CONDUIT BODIES, and entrance ELBOWS; FITTINGS for electrical metallic tubing, flexible metal conduit, intermediate metal conduit, liquid-tight flexible conduit, rigid metal conduit, and SERVICE-ENTRANCE HEADS; FITTINGS for armored cable, metal-clad cable, aluminum-sheathed cable, mineral-insulated cable, nonmetallic-sheathed cable, service-entrance cable, and tray cable, and submersible FITTINGS; FITTINGS for flexible cord, flexible nonmetallic and metallic tubing, INSULATING BUSHINGS, grips, reducing washers, and NIPPLES. Note: In Canada, fittings for metal-clad (MC) cable, intermediate metal conduit (IMC), flexible metallic tubing, flexible nonmetallic tubing, and CONDUIT BODIES are not recognized. CONDUIT BODIES are considered FITTINGS. Note: In Canada, armored cable includes Type TECK cable. Note: In Mexico and the United States, requirements for submersible FITTINGS are provided in NMX-J-235/1-ANCE, NMX-J-235/2-ANCE, or UL 50. Note: In Mexico, intermediate metal conduit is designated as semi-heavy metal conduit. 1.3 The requirements in Clause 5.7 cover CONDUIT BODIES for rigid polyvinyl chloride (PVC) conduit. These products are intended to be used with both heavy-wall and thin-wall rigid PVC conduit, ELBOWS, and other bends. The products covered by these requirements are intended to be joined to rigid polyvinyl chloride (PVC) conduit and rigid PVC ELBOWS and other bends in the field by means of a cement that is, or contains, a solvent for polyvinyl chloride. 1.4 These requirements do not cover FITTINGS intended for use in hazardous locations as defined in the National Electrical Code, ANSI/NFPA 70, the Canadian Electrical Code (CEC), Part I, CSA C22.1, and the Standard for Electrical Installations, NOM-001-SEDE. 1.5 These requirements do not cover FITTINGS intended for use with surface raceway systems. 1.6 These requirements do not cover conduit NIPPLES, threaded ELBOWS, and threaded COUPLINGS intended for use with rigid metal conduit, intermediate metal conduit, or electrical metallic tubing.

Conduit, Tubing, and Cable Fittings

JIS C 2525 ERRATUM 1:2007 勘误

ERRATUM

SANS 1574-4:2007 带固体挤制介电绝缘的软芯线，电线和电缆．第4部分：橡胶绝缘的芯线和电线

Specifies requirements for single-core flexible rubber-insulated cores and multicore flexible rubber-insulated cords of operating voltages up to and including 300 V to earth and 500 V between conductors, intended for use with electrical appliances. Insul

Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 4: Rubber-insulated cores and cords

SANS 6205:2007 可扩展性测试可伸长引线

Specifies a method of testing the ability of an extensible lead to withstand extension.

Extensibility test for extensible leads

SANS 6208:2007 扩展测试可伸长引线

Specifies a method of testing the extensibility of extensible leads.

Extension test for extensible leads

SANS 1574-5:2007 带固体挤制介电绝缘的软芯线，电线和电缆．第5部分：橡胶绝缘的电线和电缆

Specifies requirements for single-core and multicore flexible rubber-insulated cables of rated operating voltages up to and including 600 V to earth and 1 000 V between conductors, intended for use in industrial applications. Covers insulating and sheath

Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 5: Rubber-insulated cores and cables

SANS 1574-3:2007 带固体挤制介电绝缘的软芯线，电线和电缆．第3部分：PVC绝缘芯线和电缆

Specifies requirements for single-core and multicore flexible PVC-insulated cables of rated operating voltages up to and including 600 V to earth and 1 000 V between conductors, intended for use in industrial applications. Insulating and sheathing materi

Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 3: PVC-insulated cores and cables

DIN EN 61788-7:2007 超导性.第7部分:电子特征测量.微波频率下超导体的表面电阻 (IEC 61788-7-2002)

Superconductivity - Part 7: Electronic characteristic measurements - Surface resistance of superconductors at microwave frequencies (IEC 61788-7:2006); German version EN 61788-7:2006