共找到 1074 条与 低压电器综合 相关的标准,共 72 页
Safety requirements for electrical equipment for measurement, control and laboratory use. Part 2-061. Particular requirements for laboratory atomic spectrometer with thermal atomization and ionization
JB/T 3752的本部分规定了电控设备产品的型号编制方法。本部分适用于额定电压交流不超过1 000 V、频率不超过1 000 Hz或直流不超过1 500 V的通用电控设备。
Type completion method of low-voltage switchgear and controlgear assemblies.Part 2: Electrical control assemblies
本标准规定了低压成套开关设备和控制设备中配线辅件、安装辅件及专用工具等辅件产品的型号编制方法。本标准适用于额定电压交流不超过1 000 V、频率不超过1 000 Hz或直流不超过1 500 V的低压成套开关设备和控制设备中的辅件。
Type completion method for auxiliaries of low-voltage switchgear and controlgear assemblies
JB/T 3752的本部分规定了低压成套开关设备的型号编制方法。本部分适用于额定电压交流不超过1 000 V、频率不超过1 000 Hz或直流不超过1 500 V的低压成套开关设备。
Type completion method of low-voltage switchgear and controlgear assemblies.Part 1: Low-voltage switchgear assemblies
本标准规定了电器附件产品型号命名的一般原则和编制方法。本标准适用于电器附件产品。
Type coding rules for electrical accessories
Low-voltage switchgear and controlgear -- Controller device interfaces (CDIs) -- Part 2: Actuator sensor interface (AS-i)
Low-voltage switchgear and controlgear.Controller-device interfaces (CDIs) .Part 1: General rules
Low-voltage switchgear and controlgear.Controller-device interfaces (CDIs) .Part 7: CompoNet
이 표준은 심야 전력을 사용하여 온수를 발생시켜 축열조에 저장하였다가 난방에 사용하는 것으로서,정격 소비 전력이 30 kW 이하이며 최고 사용 압력이 0.35 MPa 이하인 축열식 전기 보일러(이하, 보일러라 한다.)와 단상 교류 220 V 또는 3상 교류 380 V, 380 V/440 V 겸용, 입력 전력 10 kW 이하로서 정격 압력이 0.1 MPa 이하에서 사용하는 가정용 저탕식 전기 온수기(이하, 온수기라 한다.)에 대하여 적용한다.
Electric storage water boilers for household purposes and storage tank water heaters
Connectors for electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for unshielded, free and fixed 10 way connectors with push-pull coupling for industrial environments with frequencies up to 100 MHz
UL Standard for Safety Electrical Intermediate Metal Conduit - Steel - Section/Paragraph Reference: 1.3@ 6.1.1 (exception) and 6.1.2 (exception) Subject: Addition of Evaluation Criteria for Intermediate Metal Conduit manufactured from Stainless Steel to t
Low-voltage switchgear and controlgear assemblies.Part 4: Particular requirements for assemblies for construction sites (ACS) (IEC 61439-4:2012); German version EN 61439-4:2013
Low-voltage switchgear and controlgear assemblies - Part 3: Distribution boards intended to be operated by ordinary persons (DBO); Corrigendum 1
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: actuator sensor interface (AS-i)
Low-voltage switchgear and controlgear - Product data and properties for information exchange
Low-voltage switchgear and controlgear - Part 2: circuit-breakers
"This part of IEC 60947 specifies requirements for PCB terminal blocks primarily intended for industrial or similar use. Mounting and fixing on the printed circuit board is made by soldering@ press-in or equivalent methods to provide electrical and mechanical connection between copper conductors and the printed circuit board. This standard applies to PCB terminal blocks intended to connect copper conductors@ with or without special preparation@ having a cross-section between 0@05 mm2 and 300 mm2 (AWG 30/600 kcmil)@ intended to be used in circuits of a rated voltage not exceeding 1 000 V a.c. up to 1 000 Hz or 1 500 V d.c. NOTE 1 Large cross section terminal blocks are dedicated to specific design of high current PCBs. The range up to 300 mm? is kept to cover any possible application. Examples of high current PCBs and PCB terminal blocks are shown in Annex C. NOTE 2 AWG is the abbreviation of ""American Wire Gage"" (Gage (US) = Gauge (UK)); kcmil = 1 000 cmil; 1 cmil = 1 circular mil = surface of a circle having a diameter of 1 mil; 1 mil = 1/1 000 inch. This standard may be used as a guide for special types of PCB terminal blocks with components@ such as disconnect units@ integrated cartridge fuse-links and the like. If applicable@ in this standard the term ""clamping unit"" is used instead of ""terminal"". This is taken into account in case of references to IEC 60947-1."
Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors
Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment (IEC 60947-6-1:2005); German version EN 60947-6-1:2005, Corrigendum to DIN EN 60947-6-1 (VDE 0660-114):2006-07
Low-voltage switchgear and controlgear. Product data and properties for information exchange
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号