共找到 426 条与 继电保护及自动装置 相关的标准,共 29 页
本文件规定了电力系统安全稳定控制系统的一般要求、功能和技术要求、试验方法、检验规则、标志和随行文件、包装、运输、贮存等。 本文件适用于单个厂站安全稳定控制装置、安全稳定控制系统、交直流互联电网系统保护和源网荷精准控制系统,并作为这类装置或系统的科研、设计、制造、检验和运行的依据。
General technical conditions for power system safety and stability control systems
本文件规定了精准切负荷安全稳定控制系统的总体要求、系统架构与功能、系统配置原则、试验检测等要求。 本文件适用于精准切负荷安全稳定控制系统的方案设计、设备制造和工程实施。
Technical Specifications for Accurate Load Shedding Safety and Stability Control System
本文件规定了串联变压器相关继电保护的总体要求、保护功能要求、保护整定计算要求、二次回路技术要求。 本文件适用于110kV及以上电压等级接入的统一潮流控制器、静止同步串联补偿器、可控移相器等主要柔性交流输电设备工程的串联变压器。其他电压等级、其他类型的含串联变压器的柔性交流输电设备,以及常规电网应用串联变压器的其他场景可参照执行。
Technical Guidelines for Series Transformer Relay Protection
本文件规定了高压直流保护试验装置的技术要求、测试功能要求、检验规则、包装、运输、贮存、标志、标签等。 本文件适用于采用单十二脉动电网换相换流器、双十二脉动电网换相换流器串联的高压直流输电系统保护现场试验装置的设计、生产、选型和测试。
General technical conditions for high voltage DC protection test equipment
本文件规定了配电网分布式保护的总体要求、保护功能要求、整定原则、相关回路及设备要求以及试验要求等。 本文件适用于10(20)kV配电网分布式保护的研发、设计、制造、验收和运维。6kV配电网分布式保护可参照执行。
Technical Specifications for Distributed Protection of Distribution Networks
本文件规定了智能变电站继电保护装置及二次回路的在线监视和智能诊断的架构及功能、技术要求。 本文件适用于110kV(66kV)及以上电压等级智能变电站中继电保护装置及二次回路在线监视和智能诊断。
Technical Guidelines for Online Monitoring and Intelligent Diagnosis of Relay Protection in Smart Substations
本文件规定了智能变电站配置文件运行管控系统(以下简称管控系统)的总体要求、功能要求、性能要求及安全性要求。 本文件适用于智能变电站新(改、扩)建工程验收、运维、检修过程中配置文件的管控,是配置文件运行管控系统设计、建设和应用的依据。
Technical specifications for intelligent substation configuration file operation management and control system
本文件规定了高压直流输电系统中换流器保护、极保护、双极保护、直流线路保护、直流滤波器保护、换流变压器保护、交流滤波器及其母线保护整定计算遵循的原则。 本文件适用于采用单十二脉动电网换相换流器、双十二脉动电网换相换流器串联的高压直流输电系统控制保护定值整定。
Technical regulations for control and protection setting of high voltage direct current transmission system
本文件规定了油浸式电力变压器(电抗器、换流变压器)测温装置(以下简称“测温装置”)的计量特性、校准条件、校准项目和校准方法、校准结果表达、复校时间间隔的要求等。 本文件适用于测温装置的实验室校准、现场校准,不适用于光纤传感器测温装置的校准。
Calibration specifications for transformer testers Part 3: Oil-immersed transformer temperature measurement device
本文件规定了110kV及以下电压等级通过常规互感器采样的就地化母线保护装置的检测项目、检测内容、检测方法及检测结果的判定要求等。 本文件适用于110kV及以下电压等级通过常规互感器采样的就地化母线保护装置型式试验。
Specifications for testing of local protective devices Part 4: Busbar protection
本文件规定了110kV及以下电压等级通过常规互感器采样的就地化变压器保护装置的检测项目、检测内容、检测方法及检测结果的判定要求等。 本文件适用于110kV及以下电压等级通过常规互感器采样的就地化变压器保护装置型式试验。
Specifications for testing of local protective devices Part 3: Transformer protection
本文件规定了继电保护微机型试验装置的产品分类、技术要求、功能要求、检验规则、包装、运输、存储、标志和标签、供货可靠性等要求。 本文件适用于各类电气继电器、继电保护和安全自动装置的微机型试验装置。
Technical conditions of microcomputer-based test equipment for relay protection
Permanent magnet wind turbine-converter set technical specifications
Reliability Technical Specifications for Main Control Systems of Wind Turbine Generators
Structural design specifications for electronic control products for wind turbines
Technical specifications for reliability of hydraulic pitch control systems for wind turbines
Structural environmental durability test of plateau wind turbine electrical control equipment
Technical specifications for control and protection equipment for DC access power systems in offshore wind farms
This Technical Specification applies to the manufacture of sensors and transmitters for overfill protection devices and components for self-contained overfill protection devices in stationary and stationary-use containers with water-polluting liquids. This Technical Specification
Components for overfill protection devices for liquids hazardous to aquatic environment Part 1: Manufacture of sensors and transmitters for overfill protection systems as well as components for self-sufficient overfill protection
This document specifies requirements for construction, design, performance, marking and user information for earmuffs attached to head protection and/or face protection devices, hereinafter referred to as \
Hearing protectors - General requirements - Part 3: Earmuffs attached to head protection and/or face protection devices; German version EN 352-3:2020
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号