K54 汽轮机及其辅助设备 标准查询与下载

JB/T 3596-2001 射水抽气器 性能试验规程

　　本标准规定了凝汽设备抽除空气和其它不凝结气体的射水抽气器的性能试验方法，用以测定不同工作水压力、温度下，抽吸的干空气流量与吸入侧压力之间的关系，抽气器耗功等。 　　本标准适用于火力发电站汽轮机凝汽设备的抽气器。

Performance test code for water jet air ejectors

ASME PTC 6A-2001 蒸汽涡轮机试验规程.PTC 6的补充

Test Code for Steam Turbines-Appendix to PTC 6.

DL/T 735-2000 大型汽轮发电机定子绕组端部动态特性的测量及评定

Measurement and evaluation of the dynamic characteristic on stator end windings of the large turbo-generator

DL/T 714-2000 汽轮机叶片超声波检验技术导则

Technical guide for the ultrasonic testing of turbine-blades

BS ISO 14661:2000 工业用热涡轮机(蒸气涡轮机、气体膨胀式轮机).一般要求

This International Standard specifies general requirements intended to facilitate the procurement and supply of steam turbines and gas expansion turbines primarily for industrial applications. This International Standard should serve as a basis for any application although, for special applications, supplementary specifications may also be required, for example for general and special purpose industrial steam turbines used in the petroleum and natural gas industries. This International Standard is applicable to axial- and radial-flow industrial-type turbines (steam turbines and gas expansion turbines). It specifies the basic requirements for single-stage and multi-stage impulse or reaction turbines, which are not spared or are in critical service. In addition, this International Standard also specifies some requirements for driven machines, gear units, lubrication and sealing systems, controls, instrumentation and auxiliary units for turbine plants. Exceptions to the requirements laid down in this International Standard may be agreed between the purchaser and supplier. NOTE 1 Which standard is to be applied in the individual case is the decision of the purchaser. For instance, the purchaser of a generator-driving turbine connected to the public network will generally be responsible for complying with the technical requirements of the public network regardless which standard is specified. If the purchaser of a generator-driving turbine is also the operator of the public network or if he/she is the supplier of an independent power producer (IPP), he/she usually specifies the application of IEC 60045-1. NOTE 2 Further standards on industrial steam turbines for the Petroleum and Natural Gas Industries are ISO 10436 and ISO 10437. Information on other relevant International Standards is given in the bibliography. NOTE 3 A bullet ●at the edge of the text indicates that either a decision is required or further information is to be provided by the purchaser. This information should be indicated on the data sheets (see "Introduction'') otherwise it should be stated in the quotation request or in the tender.

Thermal turbines for industrial applications (steam turbines, gas expansion turbines) - General requirements

DL/T 711-1999 汽轮机调节控制系统试验导则

Test guide of steam turbine governing system

ASME PTC 6A-2000 PTC 6的附录A,蒸汽涡轮机用测试规范

Facilitates the calculation and correction of turbine test results by furnishing numerical examples of the procedures outlined in the Test Code for Steam Turbines (PTC 6-1996). The feedwater heating cycles and gland leakoff systems have been simplified by avoiding unnecessarily long or repetitive calculations while still demonstrating the basic principles involved.

Appendix A To PTC 6, the Test Code for Steam Turbines

ANSI/ASME PTC6A-2000 附录A到PTC 6.蒸气轮机用试验代码

Facilitates the calculation and correction of turbine test results by furnishing numerical examples of the procedures outlined in the Test Code for Steam Turbines (PTC 6-1996). The feedwater heating cycles and gland leakoff systems have been simplified by avoiding unnecessarily long or repetitive calculations while still demonstrating the basic principles involved.

Appendix A to PTC 6, the Test Code for Steam Turbines

JB/T 9634-1999 汽轮机 冷油器(管式)尺寸系列和技术条件

　　本标准规定了汽轮机 冷油器（管式）尺寸系列和技术条件。 本标准适用于汽轮机 冷油器（管式）。

Size classification and specifications for tubular oil coolers of steam turbines

JB/T 9631-1999 汽轮机铸铁件 技术条件

　　本标准规定了铸铁件的技术要求、试验方法与检验规则、标志与质量证明书、防护与包装贮运。 本标准适用于砂型铸造的汽轮机用的灰铸铁件和球墨铸铁件。

Cast iron components of steam turbines

JB/T 9630.1-1999 汽轮机铸钢件 磁粉探伤及质量分级方法

　　本标准规定了铸钢件的磁粉探伤及对缺陷进行分级的方法。 本标准适用于汽轮机用主要铸钢件的表面及近表面缺陷的检验和质量等级的评定。 采用本标准时，必须提供铸钢件的磁粉探伤图，图中应注明要求探伤的部位和相应的质量等级。

Magnetic partical testing and quality classification methods of steel castings for steam turbines

JB/T 9630.2-1999 汽轮机铸钢件 超声波探伤及质量分级方法

　　本标准规定了A型脉冲反射式超声波探伤及对缺陷进行分级的方法。 本标准适用于容量大于或等于12MW电站汽轮机用铸钢件。 采用本标准时，必须提供铸钢件的超声波探伤用图，图中应注明要求探伤的部位和相应的质量等级。

Ultrasonic testing and quality classification methods of steel castings for steam turbines

JB/T 9627-1999 汽轮机组成套供应范围

　　本标准规定了汽轮机组成套供应范围。 本标准适用于发电用的汽轮机组，其它用途的汽轮机组也可参考使用。

Scope of supply of steam turbine sets

JB/T 9628-1999 汽轮机叶片 磁粉探伤方法

　　本标准规定了汽轮机叶片的湿法磁粉探伤。 本标准适用于检测叶片表面及近表面的裂纹、发纹及其它缺陷。

Method of magnetic particle inspection of steam turbine blades

JB/T 9629-1999 汽轮机承压件 水压试验技术条件

　　本标准规定了汽轮机需要进行水压试验的主要部件、水压试验要求和试验结果的判定。 本标准适用于汽轮机承压件的水压试验。

Hydrostatic tests for steam turbine pressure parts

JB/T 9559-1999 工业汽轮机用挠性联轴器

　　本标准规定了工业汽轮机用齿式联轴器、膜片式联轴器等挠性联轴器的设计、承载零件的材料、制造质量的控制，检验和选用等基本要求。 本标准适用于工业汽轮机等中、高速机械联接两轴、传递运动和动力并对所联两轴轴线间相对的轴向、径向和角向位移需有一定补偿性能的场合。

Flexible coupling for industrial steam turbine

JB/T 8990-1999 大型汽轮发电机定子端部绕组模态试验分析和固有频率测量方法及评定

本标准规定了大型汽轮发电机定子端部绕组模态试验分析和固有频率的测量方法及评定准则。 本标准适用于额定功率300 MW及以上的额定转速为3000 r/min和3600 r/min的大型汽轮发电机(包括在空冷、双水冷、全氢冷和水氢冷等)定子端部绕组的模态试验分析和固有频率测量及评定。 大型汽轮发电机在制造厂内做型式试验时，应做定子端部绕组模态试验分析。在电厂做固有频率测量时，如果发现多数线棒有接近电磁干扰力频率的固有频率时，也要做模态试验分析。 大型汽轮发电机产品在出厂前、大修后必须做定子端部绕组的固有频率测量。在电厂，有异常情况时(例如，承受突然短路、线圈磨损或者松动等)，都必须做固有频率测量。 300 MW以下的汽轮发电机，根据具体情况决定在大修后是否做固有频率测量。 进口机组也可参照此标准执行。

Model test analyses and natural frequency measurement methods of large turbo - generators on stator end windings and evaluation criteria

JB/T 8184-1999 汽轮机低压给水加热器 技术条件

　　本标准规定了汽轮机低压给水加热器(简称低加)的性能和制造技术要求。适用于火力发电厂汽轮机回热系统中管侧设计压力不高于 4.5MPa，设计温度不高于 220℃；壳侧设计压力不高于 1.5MPa，设计温度不高于 400℃ 的表面式低压给水加热器，也适用于相同工作条件的其它热交换器。

Specifications for steam turbine low pressure feed water heaters

JB/T 8188-1999 汽轮机随机设备供应范围

　　本标准规定了汽轮机随机备品、备件的供应范围。 本标准适用于固定式发电用汽轮机和工业汽轮机随机备品、备件的供应范围。

Scope of spare parts supplied by manufacturer with steam turbine

JB/T 8189-1999 汽轮机.金属高温裂纹开裂和扩展速率试验方法

　　本标准规定了汽轮机金属高温裂纹开裂和扩展速率试验方法。 本标准适用于确定汽轮机金属材料试样在高温长期应力下的缺口蠕变、高温疲劳和蠕变-疲劳交互作用的裂纹开裂和扩展速度的试验方法。

Testing method for crack initiation and propagation rate in steam turbine metals at elevates temperature