K55 水轮机及其辅助设备 标准查询与下载
共找到 247 条与 水轮机及其辅助设备 相关的标准，共 17 页
本标准规定了小型水轮机操作器的基本技术条件、试验要求、现场安装与运行、供货范围、验收及性能保证等。本标准适用于工作容量在50 000N·m以下的水轮机操作器及油压装置。
Technical requirements for operating device of small hydraulic turbine
- ICS
- 27.140
- CCS
- K55
- 发布
- 2015-07-01
- 实施
- 2015-12-01
本标准规定了小型水轮机进水阀门的技术要求，试验，安装与焊接，运行与维护，供货范围和备品备件，验收与保证，以及铭牌、包装、运输、储存方面的要求。本标准适用于水轮机进水阀门公称直径小于1000mm的蝶阀，公称直径小于500mm的球阀及公称直径小于1200mm的闸阀。
Fundamental technical requirements for inlet valves of small hydraulic turbine
- ICS
- 27.140
- CCS
- K55
- 发布
- 2015-07-01
- 实施
- 2015-12-01
本标准规定了小水电机组(含水轮机、水轮发电机，以下简称机组)及其附属设备(含水轮机进水阀、水轮机控制系统、励磁系统以及监控、保护和直流电源系统)的启动试运行试验程序和要求。本标准适用于水轮发电机组单机容量在0.5MW~15MW之间(不包括15MW)，且转轮直径小于3.3m的混流式、轴流式、冲击式水轮机；与水轮机直接连接的三相凸极同步水轮发电机(以下简称水轮发电机)及其附属设备。单机容量小于0.5MW的水电机组及其附属设备可参照执行。
Specification for small hydropower unit starting test
- ICS
- 27.140
- CCS
- K55
- 发布
- 2015-04-02
- 实施
- 2015-09-01
Basic technical conditions for small turbine water inlet valves
- ICS
- 27.14
- CCS
- K55
- 发布
- 2014-10-27
- 实施
- 2015-01-27
本标准规定了小型水轮机进水阀门的型号编制方法、一般要求、材料要求、专用技术要求、操作机构要求，以及试验、安装与运行、成套供货范围、验收与质量保证等方面要求。本标准适用于用作小型水轮机进水阀门的公称直径1000mm以下的蝴蝶阀，公称直径500mm以下的球形闸及闸阀。
Fundamental technical requirements of inlet valves for small hydraulic turbines
- ICS
- 27.140
- CCS
- K55
- 发布
- 2014-10-27
- 实施
- 2015-01-27
本标准规定了小水电机组(含水轮机、水轮发电机，简称机组)及其附属设备(含水轮机进水阀、水轮机控制系统、励磁系统以及监控、保护和直流电源系统)的安装、调试和试验的要求。 本标准适用于水轮发电机组单机容量为0.5MW~15MW(不包括15MW)，且转轮直径小于3.3m的混流式、轴流式、冲击式水轮机；与水轮机直接连接的三相凸极同步水轮发电机(简称水轮发电机)及其附属设备。 单机容量小于0.5MW的水电机组及其附属设备可参照执行。
Specification for small hydropower unit installation
- ICS
- 27.140
- CCS
- K55
- 发布
- 2014-10-15
- 实施
- 2015-03-01
本标准适用于在一台或多台小水电机组(单机容量不大于10MW、转轮直径小于3.3m)组成的小容量孤网中承担调频、调压任务的机组。
Design guidelines for small hydropower unit operated in isolated grid
- ICS
- 27.140
- CCS
- K55
- 发布
- 2014-06-29
- 实施
- 2014-11-01
本标准规定了水电站用调压阀及其控制系统的型式及参数、技术要求、试验及验收，以及标志、包装与质保。本标准适用于水电站用水轮机调压阀及其控制系统。
Fundamental technical specifications for turbine pressure relief valve and its control system
- ICS
- 27.140
- CCS
- K55
- 发布
- 2014-06-29
- 实施
- 2014-11-01
本标准规定了灯泡式水轮发电机的使用环境条件、额定值及参数、温升及温度、运行特性及电气连接、绝缘性能及其耐电压试验、机械特性、结构基本要求、通风及冷却系统、制动系统、灭火系统、检测系统和装置及元件、励磁系统、供货范围、标志、包装、运输及保管、工厂及现场试验和试运行及保证期。本标准适用于与水轮机直接连接、额定容量为5 MVA及以上的、卧轴三相50 Hz凸极同步灯泡式水轮发电机(以下简称发电机)。额定容量小于5 MVA或频率为60 Hz的出U机组可参照执行。如有特殊要求,用户和制造厂可在技术协议中规定。
Fundamental technical specifications for bulb hydro generators
- ICS
- 29.160.20
- CCS
- K55
- 发布
- 2013-12-31
- 实施
- 2014-07-01
本标准规定了中小型水轮机转轮静平衡的平衡方法、平衡品质等级及相应的检验方法。本标准适用于符合下列条件之一的中小型水轮机转轮静平衡质量的检查与验收:a) 功率为10MW及以下;b) 混流式、冲击式水轮机,转轮公称直径1.0 m及以下;c) 轴流式、贯流式水轮机,转轮公称直径3.3 m及以下。其他类型的水轮机转轮以及飞轮、旋转汕盆等水轮机旋转零部件可参考使用。
Medium and small hydraulic turbine runner static balancing test code
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-12-31
- 实施
- 2014-07-01
本标准规定了水轮机、蓄能泵和水泵水轮机的常用名词术语的符号。本标准适用于各类水轮机、蓄能泵和水泵水轮机产品标准、技术文件、科技文章及书刊。
The symbol of turbines, storage pumps and pump-turbines
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-12-31
- 实施
- 2014-07-01
Hydraulic Machines - Guide for dealing with hydro-abrasive erosion in Kaplan, Francis and Pelton turbines
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-12-13
- 实施
- 2013-12-13
Hydraulic machines. Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-09-30
- 实施
- 2013-09-30
本标准规定了水轮机电液调节系统及装置设计、制造、试验和验收的原则和要求,规范了电液调节系统及装置与水轮发电机组和电站监控系统之间的设备和功能接口要求。本标准适用于工作容量不小于3000N • m的水轮机电液调节系统及装置。
Specifications of electro-hydraulic regulating system and unit for hydraulic turbines
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-09-06
- 实施
- 2013-12-06
"This Guide serves to: a) present data on particle abrasion rates on several combinations of water quality@ operating conditions@ component materials@ and component properties collected from a variety of hydro sites; b) develop guidelines for the methods of minimizing particle abrasion by modifications to hydraulic design for clean water. These guidelines do not include details such as hydraulic profile shapes which should be determined by the hydraulic design experts for a given site; c) develop guidelines based on ""experience data"" concerning the relative resistance of materials faced with particle abrasion problems; d) develop guidelines concerning the maintainability of abrasion resistant materials and hard facing coatings; e) develop guidelines on a recommended approach@ which owners could and should take to ensure that specifications communicate the need for particular attention to this aspect of hydraulic design at their sites without establishing criteria which cannot be satisfied because the means are beyond the control of the manufacturers; f) develop guidelines concerning operation mode of the hydro turbines in water with particle materials to increase the operation life; It is assumed in this Guide that the water is not chemically aggressive. Since chemical aggressiveness is dependent upon so many possible chemical compositions@ and the materials of the machine@ it is beyond the scope of this Guide to address these issues. It is assumed in this Guide that cavitation is not present in the turbine. Cavitation and abrasion may reinforce each other so that the resulting erosion is larger than the sum of cavitation erosion plus abrasion erosion. The quantitative relationship of the resulting abrasion is not known and it is beyond the scope of this guide to assess it@ except to recommend that special efforts be made in the turbine design phase to minimize cavitation. Large solids (e.g. stones@ wood@ ice@ metal objects@ etc.) traveling with the water may impact turbine components and produce damage. This damage may in turn increase the flow turbulence thereby accelerating wear by both cavitation and abrasion. Abrasion resistant coatings can also be damaged locally by impact of large solids. It is beyond the scope of this Guide to address these issues. This guide focuses mainly on hydroelectric powerplant equipment. Certain portions may also be applicable to other hydraulic machines."
Hydraulic machines - Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines
- ICS
- 23.100.10;27.140
- CCS
- K55
- 发布
- 2013-06
- 实施
- 2019-01-18
本标准规定了并入电网(以下简称“并网”)运行的水力发电厂水轮机调节系统的技术性能与功能要求、涉网功能的试验方法。本标准适用于单机容量10MW及以上的并网运行水轮机调节系统,包括数字式、模拟式电液调节系统及装置。其他容量、类型的水轮机调节系统也可以参照执行。
Technical guide for hydraulic turbine regulating system in grid
- ICS
- 27.140
- CCS
- K55
- 发布
- 2013-03-07
- 实施
- 2013-08-01
Guide to specification of hydraulic turbine governing systems
- ICS
- 27.140
- CCS
- K55
- 发布
- 2012-12-01
- 实施
- 2012-12-07
IEC/TS 62600-201: Marine energy - Wave, tidal and other water current converters - Part 201: Tidal energy resource assessment and characterisation
- ICS
- 07.060;27.140;27.190
- CCS
- K55
- 发布
- 2012-12
- 实施
Guide to specification of hydraulic turbine governing systems
- ICS
- 27.140
- CCS
- K55
- 发布
- 2012-09-30
- 实施
- 2012-09-30
本标准规定了水轮发电机组状态在线监测系统基本技术要求、试验和检验项目、包装、运输和储存 以及技术资料等内容。 本标准适用于大、中型水电站水轮发电机组的状态在线监测系统。小型水电站水轮发电机组的状态 在线监测系统可参照使用。
Specification of on-line condition monitoring system for hydro-generator set
- ICS
- CCS
- K55
- 发布
- 2012-08-23
- 实施
- 2012-12-01
