N11 温度与压力仪表 标准查询与下载

JB/T 12596-2016 金属电容式压力传感器

本标准规定了金属电容式压力传感器的术语和定义、分类与命名、基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于金属电容式压力传感器(以下简称传感器)。

Metal capacitive pressure transducer

GOST R 8.914-2016 确保测量一致性的国家系统. 气体量热器. 验证方法

The state system for ensuring the uniformity of measurements. The gas calorimeters. The verification method

GOST R 56941-2016 冷藏, 冷冻, 深冻产品/速冻食品和冰淇淋的运输, 储存和分配用温度记录器和温度计. 周期检定

Temperature recorders and thermometers for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen food and ice cream. Periodic verification

ASTM E1363-16 热机械分析仪温度校准的标准试验方法

5.1 Thermomechanical analyzers are employed in their various modes of operation (penetration, expansion, flexure, etc.) to characterize a wide range of materials. In most cases, the value to be assigned in thermomechanical measurements is the temperature of the transition (or event) under study. Therefore, the temperature axis (abscissa) of all TMA thermal curves must be accurately calibrated either by direct reading of a temperature sensor or by adjusting the programmer temperature to match the actual temperature over the temperature range of interest. 1.1 This test method describes the temperature calibration of thermomechanical analyzers from8201;−50 to 1500°C. (See Note 1.) 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard is similar to ISO 11359–1 but addresses a larger temperature range and utilizes additional calibration materials. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7 and Note 11.

Standard Test Method for Temperature Calibration of Thermomechanical Analyzers

GOST R 56940-2016 冷藏, 冷冻, 深冻产品/速冻食品和冰淇淋的运输, 储存和分配用温度记录器. 测试, 性能, 适合性

Temperature recorders for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen food and ice cream. Tests, performance, suitability

BS EN 1434-3:2015 热量表 数据交换和接口

Heat meters. Data exchange and interfaces

JIS E 4118:2015 车辆.波登管式压力表

Rolling stock -- Bourdon tube pressure gauges

JIS B 7505-2:2015 无液压力计.第2部分:交易或认证用测量仪表

Aneroid pressure gauges -- Part 2: Measuring instruments used in transaction or certification

JB/T 12529-2015 工业钨铼热电偶技术条件

本标准规定了工业钨铼热电偶的术语和定义、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于温度范围不高于1 500℃、分度表符合GB/T 29822的带有保护管且不可拆卸的工业钨铼热电偶(以下简称热电偶)。对于其他型式或温度范围高于1 500℃的工业钨铼热电偶，可参照采用本标准的全部或部分条文。

Specifications for industrial Tungsten-Rhenium thermocouples

JB/T 8803-2015 双金属温度计

本标准规定了双金属温度计的术语和定义、产品分类与基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于具有由双金属元件和保护管组成的温度检测元件、圆形标度盘，测量范围为-80℃~500℃的双金属温度计，以及带电气接触装置的双金属温度计(以下简称温度计)。

Bimetallic thermometers

JB/T 8623-2015 工业铜热电阻技术条件及分度表

本标准规定了工业铜热电阻(以下简称铜热电阻)的分度特性及分度表、技术要求、试验方法、检验规则、标志及使用说明书。 本标准适用于-50℃~150℃整个或部分温度范围的铜热电阻。

Specification and reference table of industrial copper resistance thermometers

JJF 1540-2015 在线绕组温升测试仪校准规范

本规范适用于工频(50 Hz或60 Hz)条件下的在线绕组温升测试仪(以下简称测试仪)电阻功能的校准。本规范不适用于变频在线绕组温升测试仪的校准。

Calibration Specification for Online Testers of Winding Temperature Rise

JJG 686-2015 热水水表检定规程

本规程适用于标称口径不大于300 mm的热水水表（以下简称热水表）的首次检定、后续检定和使用中检查。 本规程所指热水表为测量流经封闭满管道热水、温度等级为T70~T130的水表，包括机械式热水表、配备了电子装置的机械式热水表、基于电磁或电子原理工作的热水表。

Verification Regulation of Hot Water Meters

JJF 1522-2015 热水水表型式评价大纲

本型式评价大纲适用于分类编码为12201000的热水水表(以下简称热水表)的型式评价，适用范围的热水表标称口径不大于300 mm、最高工作温度不超过130 ℃。

Program of Pattern Evaluation of Hot Water Meters

JIS C 1602:2015 热电偶

Thermocouples

DIN 16196:2015 带电气极限触点装置的指针式温度计.填充系统温度计和双金属片温度计

Dial indicating thermometers with electrical limit contact devices - Filled system thermometers and bimetallic thermometers

GOST R 51906-2015 温度计套管用套管, 导管, 线管和螺纹规的螺纹连接. 通用技术要求

Thread connections for casing, tubing, line pipe and thread gauges for them. General technical requirements

GOST R 8.906-2015 确保测量一致性的国家系统. 指示压力表. 参考测量仪器. 计量要求和试验方法

State system for ensuring the uniformity of measurements. Indication pressure gauges. Reference measuring instruments. Metrological requirements and test methods

GOST R 8.905-2015 确保测量一致性的国家系统. 指示压力表. 普通测量仪器. 计量要求和试验方法

State system for ensuring the uniformity of measurements. Indicating pressure gauges. Ordinary measuring instruments. Metrological requirements and test methods

ASME PTC 19.1-2013 试验不确定度

This Standard specifies procedures for evaluation of uncertainties in test measurements, parameters and methods, and for propagation of those uncertainties into the uncertainty of a test result. Depending on the application, uncertainty sources may be classified either by the presumed effect (systematic or random) on the measurement or test result, or by the process in which they may be quantified (Type A or Type B). The end result of an uncertainty analysis is a numerical estimate of the test uncertainty with an appropriate confidence level.

Test Uncertainty (PTC 19.1 - 2013)