P41 室外给水、排水工程 标准查询与下载

CJ/T 510-2017 城镇污水处理厂污泥处理 稳定标准

Stability standards for sludge treatment in urban sewage treatment plants

DB31/T 1043-2017 暴雨强度公式与设计雨型标准

本标准规定了上海市暴雨强度公式与设计雨型标准的适用范围、术语和定义、符号和单位、暴雨强度公式、暴雨设计雨型。 本标准适用于上海市市域范围的室外排水系统规划、设计与评估。

Rainstorm Intensity Formula and Design Rain Pattern Standard

DIN 19569-10:2017 污水处理厂.结构和技术设备设计原理.第10部分:热污泥干燥设备特定原理

Wastewater treatment plants - Principles for the design of structures and technical equipment - Part 10: Specific principles for the equipment for thermal sludge drying

DIN 19569-9:2017 废水处理厂.结构和技术设备的设计原则.第9部分:污水污泥的机械排放

Wastewater treatment plants - Principles for the design of structures and technical equipment - Part 9: Mechanical drainage of sewage sludge

BS ISO 16075-4:2016 灌溉工程使用处理过的废水指南. 监测

Guidelines for treated wastewater use for irrigation projects. Monitoring

BS 9101:2017 钢和铝雨水系统. 规格

Steel and aluminium rainwater systems. Specification

DB37/T 5088-2017 地下管线探测技术规程

本规程适用于以获得地下管线基础信息为目的的地下管线探测工作。

Technical Regulations for Underground Pipeline Detection

DB37/T 5089-2017 地下管线信息管理系统建设标准

本标准适用于地下管线分类、数据分层与要素编码、数据库建设、数据提交与检查、信息管理系统建设、系统验收与成果提交、数据库动态更新与信息管理系统维护等工作。

Underground pipeline information management system construction standard

ASTM A1107/A1107M-17 钢筋混凝土检修孔构造和波纹钢排水管间弹性接头的标准规格

1.1 This specification covers the design, material, and minimum performance requirements of resilient connectors used for connections between reinforced concrete structures conforming to Specifications C478 and C913 to corrugated steel drainage pipe conforming to Specifications A760 or A762. 1.1.1 These connectors are designed to provide a positive seal between the pipe and manholes or other structures subjected to internal and external hydrostatic pressures less than 10.8 psi [74 KPa]. 1.1.2 Testing under this standard is limited to hydrostatic pressures. Alternate air and vacuum pressure testing involve unique testing protocols and are not addressed under this standard. 1.1.3 Testing under this standard is conducted in a laboratory as a proof of design certification. Actual field performance testing would be accomplished and accepted under individual project performance standards or pipeline acceptance criteria, which is outside the scope of this standard. Note 1: Infiltration or exfiltration quantities for an installed system are dependent upon many factors other than the connections between manhole structures and pipe, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see 7.2.4. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Steel Drainage Pipes

ASTM C1846/C1846M-17 钢筋混凝土排水管, 雨水管和污水管基于性能制造的标准规格

1.1 This performance based specification covers reinforced concrete pipe intended to be used for the conveyance of sewage, industrial wastes, and storm water, and for the construction of culverts. 1.2 It is not the intention of this standard to dictate the material quantities and properties required for a pipe to conform to this standard except those in Section 6. Specific product formulations shall be considered proprietary and allowed to remain confidential to the manufacturer. Note 1: This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that installation conforms to the construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site. Note 2: Attention is called to the specification for Reinforced Concrete D-load Culvert, Storm Drain, and Sewer Pipe (Specification C655). The distinction between this specification and C655 is in the D-Load specified and the practice for sampling pipe for conformance to the specification. This specification relies on standard classes of pipe (Class I-V), and sampling in accordance with Section 11. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C1440-17 排水管, 排废水和排气管(DWV), 下水沟, 卫生设施和暴雨管道系统用热塑性弹性体(TPE)衬垫材料的标准规格

1.1 This specification covers thermoplastic elastomeric (TPE) gasket materials for preformed elastomeric gaskets used in shielded and non-shielded mechanical couplings. These couplings are used in gravity flow drain, waste, and vent (DWV), sewer, sanitary, and storm plumbing systems. They include couplings to join similar and dissimilar piping sizes and material. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems

CJ/T 508-2016 污泥脱水用带式压滤机

本标准规定了污泥脱水用带式压滤机（以下简称“带式压滤机”）的术语和定义、型式、型号和基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于给水排水工程中带式压滤机的制造和检验。

Belt-filter press for sludge dewatering

DB44/T 1958-2016 复合平壁钢塑嵌入式无缝排水管

本标准规定了复合平壁钢塑嵌入式无缝排水管的术语和定义、符号、代号、材料、产品结构与分类、技术要求、试验方法、检验规则、标志、运输、贮存。 本标准适用于输送介质温度在45℃以下的埋地市政排水、建筑室外排水、工业废水以及水利排水等工程的复合平壁钢塑嵌入式无缝排水管。

Composite flat wall steel-plastic embedded seamless drainage pipe

CJ/T 509-2016 拦污用栅条式格栅

本标准规定了拦污用栅条式格栅（以下简称格栅）的术语和定义、型式和型号、基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于给水排水工程中格栅的制造和检验。

Trash interception bar screen

CJ/T 507-2016 重力式污泥浓缩池周边传动浓缩机

本标准规定了重力式污泥浓缩池周边传动浓缩机（以下简称“浓缩机”）的术语和定义、型式、型号和基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于污水处理工程中浓缩机的制造和检验。

Peripheral drive thickener for gravity sludge thickening tank

DIN EN 12566-6:2016 最大50 PT的小型废水处理系统. 第6部分: 化肥池污水的预制处理设备.德文版本EN 12566-6-2016

Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent; German version EN 12566-6:2016

DIN 4045:2016 废水工程.术语

Wastewater engineering - Vocabulary

BS EN 12566-6:2016 高达50 PT的小型废水处理系统.化粪池污水用预制处理装置

Small wastewater treatment systems for up to 50 PT. Prefabricated treatment units for septic tank effluent

UL 979-2016 水处理设备

UL Standard for Safety Water Treatment Appliances (Second Edition; Reprint with revisions through and including November 8@ 2017)

DIN EN 1253-3:2016 建筑物集水沟.第3部分:质量控制.德文版本EN 1253-3-2016

Gullies for buildings - Part 3: Evaluation of conformity; German version EN 1253-3:2016