Q10 建材产品综合 标准查询与下载

DIN 52115-2:1997 岩石粒度试验.冲击试验.第2部分:碎石冲击试验

The document specifies the determination of resistance to fragmentation of ballast used for roads or railway.

Testing of aggregates - Impact test - Part 2: Impact test on ballast

ISO 11925-3:1997 对火反应试验 直接受火的建筑制品的可燃性 第3部分:多火源试验

This part of ISO 11925 specifies a series of ignition sources which can be used for the determination of the ignitability of materials, composites and assemblies when subjected to direct impingement of flames of different size and intensity but without impressed irradiance. The sources may be used in isolation or with the test method specified. This test method determines the ignitability of a material, composite or assembly and is not designed to assess any other fire parameter (e.g. flame spread). The possibility of the material composite or assembly causing secondary ignition of other materials is also considered by the observation of burning droplets or debris which may be formed. NOTE — Secondary ignition of material in a growing fire situation can be addressed using ISO 5657 which assesses the ignitability of building products by irradiance.

Reaction to fire tests - Ignitability of building products subjected to direct impingement of flame - Part 3: Multi-source test

ISO 11925-2:1997 防火试验的反作用.受火焰直接熏烤的建筑产品的可燃性.第2部分:单一火焰源试验

Reaction to fire tests - Ignitability of building products subjected to direct impingement of flame - Part 2: Single flame source test

BS 6463-101:1996 生石灰、熟石灰与天然碳酸钙.试验用试样的制备方法

Sampling powdered, granular and lump limes, milk of lime and lime putty.

Quicklime, hydrated lime and natural calcium carbonate - Methods for preparing samples for testing

KS F 4424-1996 桥梁用壶形支撑

This Korean Industrial Standard specifies the fulfillment conditions such as materials, design, production, quality qualifications and performance test of pot bearings for bridges (hereinafter referred to as "pot bearings"). Remark Normative references to this standard are as shown in annex table.

Pot bearings for bridges

NF P92-510:1996 防火安全.建材.防火试验反应.最高发热量测定

Safety against fire. Building materials. Reaction to fire tests. Determination of upper calorific value.

JC/T 624-1996 农房混凝土构件质量检测方法

Quality test method of concrete building units of farm houses

UL 723-1996 建筑材料表面燃烧特性的试验

Test for surface burning characteristics of building materials

JC/T 630-1996 石棉水泥管用橡胶圈

Rubber ring for asbestos cement pipe

JC/T 620-1996 石灰取样方法

Sampling method for lime.

JC/T 619-1996 石灰术语

Terminology of lime.

UL 1975-1996 装饰用泡沫塑料的燃烧试验

Fire tests for foamed plastics used for decorative purposes

ASTM D5050-96(2002) 石灰窑尘埃和硅酸盐水泥窑尘埃的商用标准指南

1.1 This guide is intended to evaluate and describe lime kiln dusts and Portland cement kiln dusts for uses in commercial applications. This guide is not intended to cover uses for lime or Portland cement. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Commercial Use of Lime Kiln Dusts and Portland Cement Kiln Dusts

ASTM D560-96 压实的掺土水泥混合物的冻融标准试验方法

1.1 These test methods cover procedures for determining the soil-cement losses, moisture changes, and volume changes (swell and shrinkage) produced by repeated freezing and thawing of hardened soil-cement specimens. The specimens are compacted in a mold, before cement hydration, to maximum density at optimum moisture content using the compaction procedure described in Test Methods D 558. 1.2 Two test methods, depending on soil gradation, are covered for preparation of material for molding specimens and for molding specimens as follows: Sections Test Method A, using soil material passing a No. 4 (4.75-mm) sieve. This method shall be used when 100 % of the soil sample passes the No. 4 (4.75-mm) sieve 5 Test Method B, using soil material passing a 3/4-in. (19.0-mm) sieve. This method shall be used when part of the soil sample is retained on the No. 4 (4.75-mm) sieve 6 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures

ASTM D5050-96 石灰窑尘埃和硅酸盐水泥窑尘埃的商用标准指南

1.1 This guide is intended to evaluate and describe lime kiln dusts and Portland cement kiln dusts for uses in commercial applications. This guide is not intended to cover uses for lime or Portland cement. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Commercial Use of Lime Kiln Dusts and Portland Cement Kiln Dusts

ASTM D559-96 压实的掺土水泥混合物的湿润与干燥的标准试验方法

1.1 These test methods cover procedures for determining the soil-cement losses, water content changes, and volume changes (swell and shrinkage) produced by repeated wetting and drying of hardened soil-cement specimens. The specimens are compacted in a mold, before cement hydration, to maximum density at optimum moisture content using the compaction procedure described in Test Methods D 558. 1.2 Two test methods, depending on soil gradation, are covered for preparation of material for molding specimens and for molding specimens as follows: Sections Test Method A, using soil material passing a No. 4 (4.75-mm) sieve. This method shall be used when 100% of the soil sample passes the No. 4 (4.75-mm) sieve 5 Test Method B, using soil material passing a 3/4-in. (19.0- mm) sieve. This method shall be used when part of the soil sample is retained on the No. 4 (4.75-mm) sieve 6 1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures

KS L 0005-1995 防水水泥领域标准术语

이 규격은 수경성 시멘트 공업에서 사용되는 용어에 대하여 규정한다.

Terms related to hydraulic cement

NF P92-501:1995 防火安全.建材.着火试验反应.各种厚度的刚性材料或刚性基材的包覆材料(地板或装饰料)以及厚度小于5mm挠性材料的辐射试验

Safety against fire - Building materials - Reaction to fire tests - Radiation test used for rigid materials, or for materials on rigid substrates (flooring and finishes) of all thicknesses, and for flexible materials thicker that 5 mm.

NF P92-503:1995 防火安全.建材.着火试验反应.挠性材料电炉试验

Safety against fire. Building materials. Reaction to fire tests. Electrical burner test used for flexible materials.

NF P92-504:1995 防火安全.建材.着火试验反应.火焰蔓延和蔓延速度试验

Safety against fire. Building materials. Reaction to fire tests. Flame persistance test and speed of the spread of flame.