Q31 建筑卫生陶瓷 标准查询与下载

ASTM C1208/C1208M-11 微型隧道工程,滑动内衬,管子爆裂及隧道中使用的釉面陶土管和接头的标准规范

1.1 This specification establishes the criteria for the manufacture, quality assurance testing, inspection, installation, field acceptance testing, and product marking of vitrified clay pipe to be used in microtunneling, pilot tube microtunneling, sliplining, pipe bursting, and in casings and tunnels for the conveyance of sewage, industrial wastes, and storm water. 1.1.1 Sections 3 through 7 and 9 of this specification contain manufacturing, quality assurance testing, inspection, and product marking criteria which are applicable to vitrified clay pipe prior to installation. 1.1.2 Section 8 of this specification contains criteria for the installation and field acceptance testing of vitrified clay pipe. 1.2 This specification also covers materials and test requirements for jointing of the pipe. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels

ASTM C126-11 上釉陶瓷结构用饰面瓷砖,面砖和实心砌块的标准规范

1.1 This specification covers structural clay load-bearing facing tile and facing brick and other “solid masonry units” made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500°F (655°C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1 Grade S (select), for use with comparatively narrow mortar joints. 1.1.2 Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3 Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4 Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3 Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test portion (Section 15) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

KS L 1002-2010 骨瓷餐具

이 표준은 본 차이나(골회 자기) 식기(이하 본 차이나라 한다.)에 대하여 규정한다.

Bone china table ware

JIS A 5209 AMD 1:2010 瓷砖(修改件1)

Ceramic tiles (Amendment 1)

JG/T 267-2010 建筑陶瓷砖模数

本标准规定了建筑用模数陶瓷砖的术语和定义、模数系列及尺寸偏差。 本标准适用于民用和工业建筑、构筑物墙面及地面装饰装修用的板状陶瓷制品。

Modular of ceramic for building

ISO 10545-6:2010 瓷砖.第6部分:无釉砖耐磨深度的测定

This part of ISO 10545 specifies a test method for determining the resistance to deep abrasion of all unglazed ceramic tiles used for floor coverings.

Ceramic tiles - Part 6: Determination of resistance to deep abrasion for unglazed tiles

ISO 10545-16:2010 瓷砖.第16部分:小色差的测定

This part of ISO 10545 describes a method for utilizing colour measuring instruments for quantifying the small colour differences between plain coloured ceramic tiles, which are designed to be of uniform and consistent colour. It permits the specification of a maximum acceptable value, which depends only on the closeness of match and not on the nature of the colour difference. This part of ISO 10545 is not applicable to colour variations produced for artistic purposes.

Ceramic tiles - Part 16: Determination of small colour differences

ASTM C627-10 用罗宾逊型地面检验器评价陶瓷地面砖铺盖装置标准试验方法

This test method provides a standardized procedure for evaluating performance of ceramic floor tile installations under conditions similar to actual specific usages. It can be used to make comparisons between customary basic installation methods, to establish the influence of minor changes in a particular installation method, and to judge the merit of proposed novel methods.1.1 This test method covers the evaluation of ceramic floor tile installation systems, using the Robinson -type floor tester. 1.2 This test method is intended solely for evaluating complete ceramic floor tile installation systems for failure under loads and not for evaluating particular characteristics of ceramic tile, such as abrasion resistance. This test method does not claim to provide meaningful results for other than evaluating complete ceramic floor tile installation systems. 1.3 The values stated in inch-pound units are to be regarded as the standard. The metric (SI) units in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester

ASTM C1026-10 测定瓷砖耐冻熔变化的标准试验方法

The test for resistance to freezing and thawing functions as a guide to the selection of ceramic tile suitable for outdoor service in geographic areas subjected to freezing. It can serve as a test method to verify compliance with specifications for ceramic tile, and provides a control test for determining the uniformity of tile being manufactured for exterior installations.1.1 This test method describes the procedures and equipment required to test either glazed or unglazed ceramic tile for resistance to repeated cycles of freezing and thawing. Ceramic tile of any size or shape may be tested by this test method. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring the Resistance of Ceramic Tile to Freeze-Thaw Cycling

ASTM C212-10 结构饰面瓷砖的标准规范

1.1 This specification covers structural clay load-bearing facing tile. Structural facing tile are tile designed for use in interior and exterior unplastered walls and partitions of buildings. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 6 and 7) of this standard is beyond the scope of this specification. 1.3 Tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Structural Clay Facing Tile

JC/T 1097-2009 建筑卫生陶瓷用添加剂.解胶剂

本标准规定了建筑卫生陶瓷用解胶剂的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于建筑卫生陶瓷用解胶剂。

Additives for building and sanitary ceramic:dispergators

JC/T 1094-2009 陶瓷用硅酸锆

本标准规定了陶瓷用硅酸锆的术语和定义、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于建筑陶瓷、卫生陶瓷、日用陶瓷等陶瓷产品用硅酸锆。

Zirconium silicate for ceramic

JC/T 1095-2009 轻质陶瓷砖

本标准规定了轻质陶瓷砖的术语和定义、分类、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输及贮存。 本标准适用于建筑物内外墙面装饰和建筑用绝热材料的轻质陶瓷砖。

Light-ceramic tile

JC/T 1096-2009 陶瓷用复合乳浊剂

本标准规定了陶瓷用复合乳浊剂的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于陶瓷釉料及坯体增白用的乳浊剂。

Composite opalizer for the ceramics

NF P61-204-1-1-2:2009 建筑工程.用粘合剂固定的陶瓷制品和类似瓷砖.天然石材.第1-1-2部分:外墙用工艺样式条款的承包合同清单

Building works - Ceramic and similar tiles fixing with adhesives - natural stones - Part 1-1-2 : contract bill of technical model clauses for outside walls.

NF P61-204-1-2:2009 建筑工程.用粘合剂固定的陶瓷制品和类似瓷砖.第1-2部分:材料选择的一般准则

Building works - Ceramic and similar tiles fixing with adhesives - natural stones - Part 1-2 : general criteria for material selection.

NF P61-204-1-1-3:2009 建筑工程.用粘合剂固定的陶瓷制品和类似瓷砖.天然石材.第1-1-3部分:内外地板用工艺样式条款的承包合同清单

Building works - Ceramic and similar tiles fixing with adhesives - natural stones - Part 1-1-3 : contract bill of technical model clauses for inside and outside floors.

NF P61-204-1-1-1:2009 建筑工程.用粘合剂固定的陶瓷和类似瓷砖.第1-1-1部分:内侧壁用承包标书的技术模型条款

Building works - Ceramic and similar tiles fixing with adhesives - natural stones - Part 1-1-1 : contract bill of technical model clauses for inside walls.

NF P61-204-2:2009 建筑工程.粘合剂固定的陶瓷及类似瓷砖.天然石材.第2部分:承包标书的详细管理模式条款

Building works - Ceramic and similar tiles fixing with adhesives - natural stones - Part 2 : contract bill of special administrative model clauses.

NF D12-210:2009 卫生洁具.合成材料的厕所盥洗池和表面

Sanitary appliances - Synthetic material toilet wash-basins and surfaces.