Q33 建筑玻璃 标准查询与下载

ASTM E2431-12 测定单玻璃退火建筑平板玻璃对热负荷抗性的标准实施规程

Use of this practice assumes: the glass edges shall be free from damage, the glass shall be properly glazed, the glass shall not have been subjected to abuse, and the glass edge support allows in-plane movement of the glass due to thermal expansion and contraction. This practice does not address all factors that cause thermally induced stresses in annealed glass. Factors that are not addressed include: transient thermal stresses, HVAC registers, thermally insulating window coverings, drop ceilings and other heat traps, increased solar irradiance caused by exterior reflections, variations in heat transfer coefficients other than those assumed for the steady state analysis described herein, and stresses induced by thermal sources other than the sun. Factors other than those listed above may also induce thermal stress. Many other factors shall be considered in glass selection. These factors include, but are not limited to, mechanically induced stresses, wind effects, windborne debris impacts, excessive deflections, seismic effects, heat flow, noise abatement, potential post-breakage consequences, and so forth. In addition, considerations set forth in building codes along with criteria presented in safety glazing standards and site specific concerns may control the ultimate glass type and thickness selection. The proper use of this practice is intended to reduce the risk of thermally induced breakage of annealed window glass in buildings.1.1 This practice covers a procedure to determine the resistance of annealed architectural flat glass to thermally induced stresses caused by exposure to sun and shadows for a specified probability of breakage (Pb). Proper use of this procedure is intended to reduce the possibility of thermal breakage of annealed glass in buildings. 1.2 This practice applies to vertical or sloped glazing in buildings. 1.3 This practice applies to monolithic and laminated glass of rectangular shape and assumes that all glass edges are simply supported. 1.4 This practice applies only to annealed flat soda-lime silica glass with clean cut, seamed, flat ground, or ground and polished edges that are free from damage. The glass may be clear or tinted as well as coated (not including coatings that reduce emissivity of the glass). 1.5 This practice does not apply to any form of wired, patterned, etched, sandblasted, drilled, notched, or grooved glass or glass with surface and edge treatments, other than those described in 1.4, that alter the glass strength. 1.6 This practice does not address uniform loads such as wind and snow loads, safety requirements, fire, or impact resistance. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. For conversion of quantities in various systems of measurements to SI units refer to IEEE/ASTM SI-10. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings

ASTM E1300-12ae1 测定建筑玻璃负载电阻的标准实施规程

1.1 This practice describes procedures to determine the load resistance (LR) of specified glass types, including combinations of glass types used in a sealed insulating glass (IG) unit, exposed to a uniform lateral load of short or long duration, for a specified probability of breakage. 1.2 This practice applies to vertical and sloped glazing in buildings for which the specified design loads consist of wind load, snow load and self-weight with a total combined magnitude less than or equal to 15 kPa (315 psf). This practice shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves. 1.3 This practice applies only to monolithic and laminated glass constructions of rectangular shape with continuous lateral support along one, two, three, or four edges. This practice assumes that (

Standard Practice for Determining Load Resistance of Glass in Buildings

ASTM E2875/E2875M-12 处理平板玻璃用个人防护设备的标准指南

The goal of this guide is to aid in the selection of PPE for the handling of glass that will best protect the affected employee from the remaining hazards identified in the local hazard assessment process. This guide assumes that a proper hazard assessment has been conducted, the hazards have been mitigated to the greatest extent possible by non-PPE means (engineering, administrative or work practice controls), and a hazard still exists that can only feasibly be controlled by the use of PPE.1.1 This guide covers the minimum requirements for proper personal protective equipment (PPE) for the safe handling of flat glass. 1.2 Purpose8212;When engineering, administrative, and work practice controls are not feasible, the remaining hazard must be controlled with personal protective equipment (PPE). This guide will provide direction on what PPE should be utilized. Following this guidance will help to minimize the possibility or severity of injuries or both to personnel while working with or in the vicinity of flat glass. 1.3 Nothing in this guide shall be interpreted as requiring any action that violates any statute or requirement of any federal, state, or other regulatory agency. 1.4 This guide may be used by employers and employees. The required PPE shall be evaluated on a regular basis to determine suitability. 1.5 Units8212;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Personal Protective Equipment for the Handling of Flat Glass

JC/T 2072-2011 中空玻璃用干燥剂

本标准规定了中空玻璃用干燥剂的术语和定义、分类和规格、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于吸附中空玻璃间隔层中水分的干燥材料。

Desiccant for insulating glass units

JC/T 2069-2011 中空玻璃间隔条.第1部分：铝间隔条

本标准规定了中空玻璃铝间隔条的术语和定义、材料、规格及分类、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于中空玻璃用铝间隔条。

Spacer for insulating glass units.Part 1:Aluminum spacer

ISO 28278-1:2011 建筑玻璃.玻璃装配结构密封用玻璃产品.第1部分:有支撑和无支撑的整块与多层玻璃装配

Glass in building - Glass products for structural sealant glazing - Part 1: Supported and unsupported monolithic and multiple glazing

ISO 11485-1:2011 建筑玻璃.曲面玻璃.第1部分:术语和定义

Glass in building - Curved glass - Part 1: Terminology and definitions

ISO 11485-2:2011 建筑玻璃.曲面玻璃.第2部分:质量要求

This part of ISO 11485 specifies the quality requirements for curved glass used in general building construction, furniture, display and various other non-automotive applications.

Glass in building - Curved glass - Part 2: Quality requirements

DIN EN ISO 12543-5:2011 建筑玻璃.夹层玻璃和夹层安全玻璃.第5部分:尺寸规格和边缘处理(ISO 12543-5-2011).德文版 EN ISO 12543-5-2011

Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and edge finishing (ISO 12543-5:2011); German version EN ISO 12543-5:2011

DIN EN ISO 12543-4:2011 建筑玻璃.夹层玻璃和夹层安全玻璃.第4部分:耐久性试验方法(ISO 12543-4-2011).德文版 EN ISO 12543-4-2011

Glass in building - Laminated glass and laminated safety glass - Part 4: Test methods for durability (ISO 12543-4:2011); German version EN ISO 12543-4:2011

DIN EN ISO 12543-1:2011 建筑玻璃.夹层玻璃和夹层安全玻璃.第1部分:组成部分的定义和描述(ISO 12543-1-2011).德文版 EN ISO 12543-1-2011

Glass in building - Laminated glass and laminated safety glass - Part 1: Definitions and description of component parts (ISO 12543-1:2011); German version EN ISO 12543-1:2011

DIN EN ISO 12543-3:2011 玻璃建筑.夹层玻璃和夹层安全玻璃.第3部分：夹层玻璃(ISO 12543-3-2011). 德文版 EN ISO 12543-3-2011

Glass in building - Laminated glass and laminated safety glass - Part 3: Laminated glass (ISO 12543-3:2011); German version EN ISO 12543-3:2011

DIN EN ISO 12543-2:2011 建筑玻璃.夹层玻璃和夹层安全玻璃.第2部分:夹层安全玻璃(ISO 12543-2-2011).德文版 EN ISO 12543-2-2011

Glass in building - Laminated glass and laminated safety glass - Part 2: Laminated safety glass (ISO 12543-2:2011); German version EN ISO 12543-2:2011

JIS R 3220:2011 建筑玻璃.镀银平板玻璃镜

Glass in building -- Silvered, flat-glass mirror

JIS R 3202:2011 浮法玻璃和抛光平板玻璃

Float glass and polished plate glass

NF P78-211-1:2011 建筑玻璃.层压玻璃和层压安全玻璃.第1部分:组合零件的定义和描述.

Glass in building - Laminated glass and laminated safety glass - Part 1 : definitions and description of component parts.

NF P78-211-5:2011 建筑玻璃.层压玻璃和层压安全玻璃.第5部分:尺寸规格和边缘加工.

Glass in building - Laminated glass and laminated safety glass - Part 5 : dimensions and edge finishing.

NF P78-211-2:2011 建筑玻璃.层压玻璃和层压安全玻璃.第2部分:层压安全玻璃.

Glass in building - Laminated glass and laminated safety glass - Part 2 : laminated safety glass.

NF P78-211-6:2011 建筑玻璃.层压玻璃和层压安全玻璃.第6部分:外观.

Glass in building - Laminated glass and laminated safety glass - Part 6 : appearance.

NF P78-211-3:2011 建筑玻璃.层压玻璃和层压安全玻璃.第3部分:层压玻璃.

Glass in building - Laminated glass and laminated safety glass - Part 3 : laminated glass.