S50 铁路车辆综合 标准查询与下载

KS R 9160-2002 铁路车辆振动特性.测定方法

이 규격은 주행시 여객차 차체에서의 진동 가속도, 진동수 등의 진동 특성 측정 방법에 대하

Vibration characteristics of railway rolling stock－Measuring methods

KS R 9155-2002 铁路车辆用高速断路器试验方法

이 규격은 철도 차량의 고전압 직류 회로에, 단일체 또는 고속도 감류기로 사용되는 철도 차

Railway rolling stock-High speed circuit breaker-Test methods

KS R 9156-2002 铁路车辆用电器设备试验基本规定

이 규격은 철도 차량에 사용하는 전자 기기(이하 전자 기기라 한다.)의 시험에 관한 일반

General rules for tests of electronic equipmentused on railway rolling stock

KS R 9152-2002 铁路车辆电弧焊接头设计方法

이 규격은 철도 차량의 구조체, 대차 그 밖의(1) 용접 구조에 쓰이는 아크 용접 이음(이

Design Methods of arc welded joints for railway rolling strock

TB/T 3063-2002 旅客列车DC600V供电系统技术条件

本标准规定了旅客列车DC600V 供电系统及部件的技术要求、检验规则及试验方法等。 本标准适用于电力牵引的DC600V供电制式旅客列车及动力集中动车组。 本标准也 适用于内燃牵引的DC600V供电制式旅客列车及动车组(供电辅助发电机组除外)。 动力分散动车组参照执行本标准。

Technical conditions of DC600V power supply system for passenger trains

BS EN 50155:2001 轨道交通.铁道车辆上使用的电子设备

This standard applies to all electronic equipment for control, regulation, protection, supply, etc., installed on rail vehicles and associated with: - either the accumulator battery of the vehicle; - or a low voltage power supply source with or without a direct connection to the contact system (transformer, potentiometer device, auxiliary supply); with the exception of electronic power circuits, which conform to EN 50207. This standard covers the conditions of operation, design, construction, and testing of electronic equipment, as well as basic hardware and software requirements considered necessary for competent, reliable equipment. Additional requirements in other standards or individual specifications may complement this standard, if they are justified. Specific requirements related to practices necessary to assure defined levels of functional safety are to be determined in accordance with subclauses 4.6.3.1 and 4.6.3.2 of EN 50126 and its informative annex A. Software safety integrity level of 1 or higher shall only be considered when it is shown that a residual safety risk remains and that it has to be carried by the software driven programmable electronic system. In such a case (i.e. software safety integrity level 1 or higher), EN 50128 is applicable. For the purpose of this standard, electronic equipment is defined as equipment mainly composed of semiconductor devices and recognized associated components. These components will mainly be mounted on printed boards. NOTE Sensors (current, voltage, speed, etc.) and firing unit printed board assemblies for power electronic devices are covered by this standard. Complete firing units are covered by EN 50207.

Railway applications - Electronic equipment used on rolling stock

NF F74-159-2:2001 轨道交通.通信、信号和处理系统.第2部分:开放式传输系统内的与安全相关的通信

Railway applications - Communication, signalling and processing systems - Part 2 : safety-related communication in open transmission systems.

DIN 25003:2001 轨道交通.道路车辆的分类.概述、术语和定义

The document indicates the terms and definitions of rail vehicles according to their technical characteristics and is intended to facilitate oral and written communication. The document incorporates the English and French translation of the terms for information.

Railway applications - Classification of rail vehicles - Survey, terminology, definitions

NF F74-159-1:2001 轨道交通.通信、信号和处理系统.第1部分:在封闭传输系统中与通信有关的安全

Railway applications - Communication, signalling and processing systems - Part 1 : safety-related communication in closed transmission systems.

NF F74-128:2001 轨道交通.通信、信号和处理系统.铁路控制和防护系统用软件

Railway applications - Communications, signalling and processing systems - Software for railway control and protection systems.

NF F17-001:2001 轨道交通.铁路车辆车体的结构要求

Railway applications - Structural requirements of railway vehicle bodies.

KS R 9216-2000 铁路车辆.乘坐舒适度测定和评估方法

이 규격은 운행하는 차량 승객의 승차감 측정 및 평가 방법에 대하여 규정한다. 이 규격의

Railway rolling stock－Test and evaluation method for passenger comfort

KS R 9218-2000 铁路车辆.轮副安装的检查方法

이 규격은 철도 차량(최고 속도 150km/h 이하)에 사용되는 차축과 고탄소강 일체 압연

Railway rolling stock - Assembly and test methods of wheelsets

KS R 9219-2000 铁路车辆自动复合连接器

이 규격은 철도 차량에 사용하는 자동 복합 연결기(이하 복합 연결기라 한다.)에 대하여 규

Automatic complex coupler for railway rolling stock

KS R 9217-2000 铁路车辆.运行阻力试验方法

이 규격은 철도 차량의 주행 저항을 측정하기 위한 주행 저항 시험에 대하여 규정한다.

Railway rolling stock－Test methods for running resistance

BS EN 12663:2000 轨道交通.铁路车辆车身结构要求

This European Standard defines minimum structural requirements for railway vehicle bodies. This European Standard specifies the loads vehicle bodies shall be capable of sustaining, identifies how material data shall be used and presents the principles to be used for design verification by analysis and testing. The railway vehicles are divided into categories which are defined only with respect to the structural requirements of the vehicle bodies. These structural requirements should not be confused with operating requirements. It is the responsibility of the operator to decide as to which structural category railway vehicles shall be designed. Some vehicles may not fit into any of the defined categories; the structural requirements for such railway vehicles should be specified by the operator using the principles presented in this European Standard. The standard applies to all railway vehicles within the EU and EFTA territories. The specified requirements assume operating conditions and circumstances such as are prevalent in these countries.

Railway applications - Structural requirements of railway vehicle bodies

NF F21-206-2:2000 轨道交通.铁路车辆.导电弓架:特性和试验.第2部分:地下铁道和轻型铁路车辆的导电弓架

Railway applications - Rolling stock - Pantographs : characteristics and tests - Part 2 : pantographs for metro and light rail vehicles.

TB/T 2204.1-2000 车辆车轴轮座弧度样板

本标准规定了车辆滚动轴承车轴轮座前肩弧度A型样板的结构型式和基本尺寸。 本标准适用于检查经过精加工后的车辆滚动轴承车轴A型轮座前肩弧度样板的设计。

Vehicle axle wheel seat radian sample

TB/T 2204.3-2000 车辆滚动轴承车轴 轮座前肩、轴颈后肩弧度样板

本标准规定了车辆滑动轴承车轴轮座前肩、轴颈后肩弧度样板的结构型式和基本尺寸。 本标准适用于检查经过精加工后的车辆滑动轴承车辆(轴型:B，C，D，E，F，G)轮座前肩和轴颈后肩弧度样板的设计。

Radian sample of the front shoulder of the vehicle rolling bearing axle wheel seat and the rear shoulder of the journal

TB/T 2204.2-2000 车辆滚动轴承车轴 轮座前肩弧度B、C型样板

本标准规定了车辆滚动轴承车轴轮座前肩弧度B、C型样板的结构型式和基本尺寸。 本标准适用于检查经过精加工后的车辆滚动轴承车轴B型和C型轮座前肩弧度样板的设计。

Front shoulder radian B and C type samples of vehicle rolling bearing axle and wheel seat