T24 制动系统 标准查询与下载

SAE J1476-2008 额定总重量超过4500公斤(10000镑)的卡车和客车候车制动结构完整性试验规程

This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR. The main purpose of the document is to evaluate the structural integrity of a vehicle's parking brake system. However, other areas, such as suspension and drivetrain system, may also be evaluated during the test, provided that the criteria and procedure detailed as follows are not modified in any way.

Parking Brake Structural Integrity Test Procedure Vehicles over 4500 kg (10,000 lb) GVWR Truck and Bus

KS R ISO 6310:2008 道路车辆.制动衬片.压缩应力试验方法

이 표준은 도로 차량 디스크 브레이크 패드 조립품, 드럼 브레이크 조립품 및 배킹 플레이트

Road vehicles-Brake linings-Compressive strain test method

KS R ISO 21994:2008 乘用车.防抱死制动系统(ABS)直线制动停车距离.开环试验方法

이 표준은 ABS가 완전하게 작동하는 상태의 직선 제동에서 정지 거리를 결정하기 위한 개회

Passenger cars－Stopping distance at straight-line braking with ABS－Open-loop test method

KS R ISO 611:2008 道路车辆.机动车及其挂车的制动.词汇

이 표준은 KS R ISO 3833에 정의된 전동 차량, 트레일러 또는 이들이 결합된 차량

Road vehicles-Braking of automotive vehicles and their trailers-Vocabulary

SAE J2330-2008 步行工作机械制动系统性能要求和试验程序

This SAE Standard specifies minimum performance and test criteria for brake systems to enable uniform assessment of the braking capability of walk-along self-propelled work machines with a mass greater than 115 kg. Service and parking brake systems are covered by this document.

Walk-Along Work Machines Braking Systems Performance Requirements and Test Procedures

SAE J1704-2008 硼酸盐酯基制动液

This SAE standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. This standard covers different levels of performance properties compared to the SAE J 1703 and SAE J 1705 documents on brake fluids. These fluids are not intended for use under arctic conditions or in braking systems requiring the use of mineral oil based hydraulic fluid These fluids are designed for use in braking systems fitting with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).

Borate Ester Based Brake Fluids

BS ISO 21069-2:2008 道路车辆 用辊式制动试验器对带有最大允许总质量大于3.5t的车辆制动系统的试验 气液压和纯液压制动系统

Road vehicles - Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester - Air over hydraulic and purely hydraulic braking systems

SAE J1703-2008 机动车辆制动液

This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions.These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).

Motor Vehicle Brake Fluid

JT/T 721-2008 客车电涡流缓速器 装车性能要求和试验方法

本标准规定了客车电涡流缓速器（以下简称“缓速器”）装车性能要求和试验方法。 本标准适用于可载乘员数（不包括驾驶员）多于22人，且最大设计总质量超过5000kg的客车。其他客车可参照执行。

Requirements and test methods of electromagnetic retarder for the ues of bus

SAE J1512-2008 手动间隙调节器性能要求

These performance requirements have been established for manual slack adjusters when tested to SAE J1461.To establish acceptable levels of performance for manual slack adjusters.

Manual Slack Adjuster Performance Requirements

JIS D 2605 ERRATUM 1:2008 勘误表

ERRATUM

KS R ISO 21069-1:2008 道路车辆.使用辊式制动试验器的最大容许总质量超过3.5.t车辆上制动系统试验.第1部分:气压制动系

이 표준은 UNECE R.E.3에서 정의된 범주 M2, M3, N2, N3, O3 및 O4

Road vehicles-Test of braking systems on vehicles with a maximum authorized total mass of over 3.5 t using a roller brake tester-Part 1:Pneumatic braking systems

KS R ISO 6312:2008 道路车辆.制动闸衬.圆盘制动片和鼓式制动器蹄片装置的剪切试验规程

이 표준은 디스크 브레이크 패드 및 드럼 브레이크 슈 어셈블리의 캐리어와 라이닝 재질 사이

Road vehicles-Brake linings-Shear test procedure for disc brake pad and drum brake shoe assemblies

KS R ISO 12161:2008 道路车辆.电动机车和拖车耐摩擦制动系统.试验方法

이 표준은 ECE-R 13/09의 부록 1에서 6까지를 따르도록 설계된 범주 M, N 및

Road vehicles－Endurance braking systems ofmotor vehicles and towed vehicles－Test procedures

QC/T 564-2008 乘用车制动器性能要求及台架试验方法

本标准规定了乘用车行车制动器的性能要求及台架试验方法。 本标准适用于GB/T 15089规定的M类车辆用行车制动器总成及摩擦衬片（衬块）总成。

Performance requirements and bench test methods for passenger car brake

SAE J748-2008 最大3000 psi液压方向控制阀

This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial machinery equipment as referenced in SAE J1116. The purpose is to establish port area to flow relationship and match valve spool eye ends in relation to rated capacity. Port connections are optional for either the 4-bolt split flange connection or the internal straight thread "O" ring connection.

Hydraulic Directional Control Valves, 3000 psi Maximum

ISO 21069-2:2008 道路车辆.用辊式制动试验器对带有最大允许总质量大于3.5t的车辆制动系统的试验.第2部分:空气液压和纯液压制动系统

This part of ISO 21069 describes a procedure that generates comparable measurement results in roller brake testing, such that the efficiency of the service braking system can be assessed reliably wherever the roller brake tests are performed. The following items are covered in this part of ISO 21069: - symbols and definitions; - test methods; - test conditions; - test equipment required; - accuracy of test equipment; - data recording and calculation needed; - presentation of results; - assessment criteria for pass/fail. The procedure described in this part of ISO 21069 is not applicable to passenger cars.

Road vehicles - Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester - Part 2: Air over hydraulic and purely hydraulic braking systems

BS ISO 21995:2008 道路车辆.带3.5 t以上允许质量的车辆空气制动系统的试验.用辊筒制动试验器对参考值的采集和使用

ISO 21995:2008 provides a method for the acquisition of suitable braking reference values that the manufacturer is required to provide, and for the use of these reference values in periodical technical inspection (PTI) on air brake systems.

Road vehicles - Test of vehicle air braking systems with a permissible mass of over 3,5 t. Acquisition and use of reference values using a roller brake tester

KS R ISO 4039-1:2008 道路车辆.气压制动系统.第1部分:有平面密封面的管、阳螺纹管接头和螺纹孔

이 규격은 2 MPa(20 bar) 미만의 압력을 가진 압축 공기를 사용하는 도로 차량의

Road vehicles-Pneumatic braking systems-Part 1:Pipes, male fittings and tapped holes with facial sealing surface

KS R ISO 4039-2:2008 道路车辆.气压制动系统.第2部分:有锥形密封面的管、阳螺纹管接头和螺纹孔

이 규격은 2 MPa(20 bar) 미만의 압력을 가진 압축 공기를 사용하는 도로 차량의

Road vehicles－Pneumatic braking systems－Part 2：Pipes, male fittings and tapped holes with conical sealing surface