T60 拖拉机综合 标准查询与下载

JB/T 7325-1994 农林窄轮距轮式拖拉机防护装置.强度试验方法和验收条件

本标准规定了农业、林业窄轮距轮式拖拉机防护装置的强度试验方法和验收条件。 本标准适用于具有两轴的充气轮胎拖拉机,其前轴和后轴的离地间隙应不大于600mm;后轮固定 或可调式最小轮距应不大于1150mm;拖拉机空载质量(包括防护装置和制造厂提供的最大轮胎)应大于600kg,如具有前置式防护装置应同时小于3000kg。

The strength testing method and accepting condition of protective structures on narrow-track wheeled agricultural and forestry tractors

JIS D 6710:1994 农用拖拉机.前部和中部动力输出轴

この規格は，農業用トラクタ(ローン及びガーデントラクタを含む。)のフロント及びミッドの動力取出軸(以下，軸という。)について規定する。

Agricultural tractors -- Front and mid power take-off

JIS A 8420:1994 牵引车及操作装置术语和说明项目

Terminology standard form of specifications and testing methods of tractors

NF U02-061:1993 农林拖拉机和机具.座位参考点.测定方法

TRACTORS AND MACHINERY FOR AGRICULTURE AND FORESTRY. SEAT REFERENCE POINT. METHOD OF DETERMINATION.

SN/T 0261-1993 出口拖拉机检验规程

Rules for the inspection of tractors for export

ISO 789-3:1993 农业拖拉机 试验程序 第3部分:转向和回转圆直径

Specifies a method of determining the turning and clearance diameters of wheeled agricultural tractors. Applies to wheeled agricultural tractors having at least two axles fitted with pneumatic tyres.

Agricultural tractors; test procedures; part 3: turning and clearance diameters

ISO 789-2:1993 农业拖拉机 试验程序 第2部分:后置三点悬挂装置提升能力

Specifies test procedures for determining the lifting capacity of rear-mounted three-point linkage systems: a) the maximum vertical force which can be exerted by the hydraulic lift at the lower hitch points throughout their full range of movement; b) the maximum vertical force which can be exerted by the hydraulic lift, at a point 610 mm to the rear of the hitch points on a frame attached to the three-point linkage, throughout its full range of movement; c) optionally, the ability of the lifting system to maintain the load in the lifted position without hydraulic power.

Agricultural tractors; test procedures; part 2: rear three-point linkage lifting capacity

JB/T 6713-1993 保证拖拉机液压系统 清洁度的工艺规范

Process Specifications for Ensuring the Cleanliness of Tractor Hydraulic System

JB/T 6702-1993 拖拉机和农用运输车 产品图样及设计文件编号规则

Numbering rules for product drawings and design documents of tractors and agricultural transport vehicles

JB/T 6715-1993 农业拖拉机驾驶座标志点

本标准规定了农业拖拉机驾驶座标志点的位置及其测量方法。 本标准适用于轮式和履带拖拉机的单人驾驶座。

Agricultural tractor driver's seat sign point

BS 6347-8:1993 农用拖拉机的性能评估 发动机空气滤清器的测试方法

Additional tests to those specified in ISO 5011 for the special conditions relating to agricultural tractors.

Performance assessment of agricultural tractors. Method of testing engine air cleaners

BS 6347-7:1993 农用拖拉机的性能评估 轴功率测定方法

Wheeled or track laying vehicles, one or two driven axles.

Performance assessment of agricultural tractors. Method for determination of axle power

ISO 789-9:1990/Amd 1:1993 农业拖拉机 试验程序 第9部分:牵引功率试验 修改1

Amends the first paragraph of subclause 6.3.

Agricultural tractors; test procedures; part 9: power tests for drawbar; amendment 1

ISO 4252:1992 农业拖拉机 操作员工作位置、入口和出口 尺寸

Specifies design dimensions concerning minimum dimensions of access doorways; number, location and minimum dimensions of emergency exits; minimum internal clearance dimensions. Applies to tractors for agriculture having a minimum track width exceeding 1150 mm.

Agricultural tractors; operator's workplace, access and exit; dimensions

JB/T 6294-1992 农业拖拉机 型式检验规则

Agricultural tractor type inspection rules

NY/T 209-1992 农业轮式拖拉机推广鉴定方法

Appraisal method for extension of agricultural wheeled tractors

AIR FORCE A-A-58006-1992 多用途四轮驱动拖拉机

The General Services Administration has authorized the use of this comercial item description.

4-WHEEL DRIVEN, MULTI-PURPOSE TRACTOR

ISO 789-7:1991 农业拖拉机 试验程序 第7部分:轴功率测定

Gives measurement units and tolerances, and includes general requirements. Annex A (test report) forms an integral part of this standard. Annexes B, C, D (reference fuels) and E are for information only.

Agricultural tractors; test procedures; part 7: axle power determination

BS 5510:1991 农用轮式拖拉机最高速度测定方法

Methods for calculating maximum design speed and the maximum travel speed.

Methods for determination of maximum speeds of agricultural wheeled tractors

BS 5731:1991 农林拖拉机外部设备控制器安装孔和基座规范

Requirements for mounting additional controls/instrumentation used for remote operation of supplementary machinery/equipment with agricultural/forestry tractors and the provision of an adjacent electrical power point. Gives requirements for an aperture through which the control cable or hose can enter the tractor cab.

Specification for mountings and apertures for external equipment controls on agricultural and forestry tractors