共找到 81 条与 发动机 相关的标准,共 6 页
本文件描述了摩托车和轻便摩托车发动机最大扭矩和最大净功率的测量方法。 本文件适用于摩托车和轻便摩托车用发动机(以下简称“发动机”)。
Measurement methods of maximum torque and maximum net power of engines for motorcycles and mopeds
本标准规定了摩托车和轻骑摩托车用火花点火式发动机在台架上进行性能试验、可靠性试验和耐久性试验的方法。 本标准适用于摩托车和轻便摩托车用火花点火式发动机。
Method of bench test of engine for motorcycles and mopeds
本标准规定了摩托车和轻便摩托车发动机最大扭矩和最大净功率的测量方法。 本标准适用于摩托车和轻便摩托车用发动机。
Measurement methods of maximum torque and maximum net power of engines for motorcycles and mopeds
Technical specifications for motorcycle and moped engine cylinder blocks
Motorcycle and moped engine camshafts
本标准规定了交流充电桩与车辆充电控制装置之间基于控制器局域网(CAN)的通信物理层、数据链路层及应用层的定义。 本标准适用于采用电动汽车150A三相交流充电接口,交流充电桩与车辆充电控制装置之间的通信协议。
150A three-phase AC charging communication protocol for electric vehicles
本标准规定了摩托车和轻便摩托车化油器的抽样规定、检验项目及指标规定、检验方法、评定方法。 本标准适用于摩托车和轻便摩托车化油器(以下简称化油器)质量评定。
Quality assessment of carburetors for motorcycles and mopeds
本标准规定了摩托车和轻便摩托车用空气滤清器滤芯的技术要求、试验方法和检验规则以及标志、包装、运输和储存。本标准适用于滤纸、非织造布和泡沫塑料制作的、发动机排量不大于250mL的摩托车和轻便摩托车用空气滤清器滤芯(以下简称滤芯)。排量250mL以上的摩托车和轻便摩托车用空气滤清器滤芯也可参照执行。
Specifications of air filter element for motorcycles and mopeds
本标准规定了摩托车和轻便摩托车湿式离合器的要求、试验方法、检验规则、标志、包装、运输及储存。本标准适用于摩托车和轻便摩托车(以下简称摩托车)机械、湿式多片(JPS)离合器(以下简称离合器)。
Wet clutch for motorcycles and mopeds
本标准规定了摩托车和轻便摩托车发动机试验室内测定表面平均声压级的测量仪器、测量条件、测量方法和数据整理与测量结果。本标准适用于摩托车和轻便摩托车用往复活塞式内燃机(以下简称发动机)噪声测量。
Measurement method of acoustic noise for engines of motorcycles and mopeds
本标准规定了摩托车和轻便摩托车用转子机油泵的要求、试验方法、检验规则、标志、包装、运输及存储。本标准适用于摩托车和轻便摩托车发动机(以下简称发动机)用转子机油泵(以下简称机油泵)。
Technicalrequirements for the motorcycle and moped rotor oil pump
本标准规定了摩托车和轻便摩托车发动机型号编制方法。本标准适用于摩托车和轻便摩托车发动机型号的编制。
Codina method for engine type of motorcycle and moped
本标准规正了靡托牛和轻便摩托牛 -邑动电机(以 卜简称起动电机)的要求、试验条件、试验设 备、试验方法、检验规则和标志、包装、运输及储存o 本标准适用=摩托车和轻便摩托车庐 琶动电机。
Specifications for starter motors for motorcycles and mopeds
Small Off-Road Ground-Supported Outdoor Power Equipment - Gasoline Fuel Systems - Performance Specifications and Test Procedures
Specifications for magneto motors for motorcycles and mopeds
This International Standard specifies methods for evaluating the performance of engines designed for mopeds as defined in ISO 3833, in particular with a view to the presentation of power curves and specific fuel consumption at full load as a function of engine speed, for net power assessment. It is applicable to reciprocating internal combustion engines (spark-ignition), excluding free-piston engines, and rotary piston engines, either naturally aspirated or pressure-charged and equipped with either mechanical pressure-charger or turbocharger.
Mopeds - Engine test code - Net power
Motorcycles. Engine test code. Net power
This International Standard specifies methods for evaluating the performance of engines designed for motorcycles as defined in ISO 3833, in particular with a view to the presentation of power curves and specific fuel consumption at full load as a function of engine speed, for net power assessment. It is applicable to reciprocating internal combustion engines (spark-ignition or compression-ignition) — excluding free-piston engines — and rotary piston engines, either naturally aspirated or pressure-charged and equipped with either mechanical pressure-charger or turbocharger. Particular specifications for the test of compression-ignition engines are specified in Annex A.
Motorcycles - Engine test code - Net power
本标准规定了摩托车和轻便摩托车发动机组合式曲轴用曲柄半轴的要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于摩托车和轻便摩托车发动机组合式曲轴用曲柄半轴。
Motorcycle and moped engines Combined crankshaft Crankshaft
本标准规定了摩托车和轻便摩托车簧片阀式二次空气补给机构的耐久性要求与试验方法。 本标准适用于由单向簧片阀和二次空气截止阀组合而成的机构。其他形式的机构可以参照使用。
Durability requirements and testing methods of reed valve type second air injectors for motorcycles and mopeds
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号