U05 船舶用材料及其检验方法 标准查询与下载

NAVY QPL-19004-23-1997 海军军舰上用固定便携式通风式离心鼓风机

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defens.

FANS, CENTRIFUGAL, FIXED AND PORTABLE, VENTILATION, NAVAL SHIPBOARD

ASTM E1317-97a 船舶表面涂层易燃性的试验方法

1.1 This fire-test-response standard describes a procedure for measuring fire properties associated with flammable behavior of surface finishes used on noncombustible substrates aboard ship (Note 1). In particular, these include surface finishes intended for use in ship construction such as deck surfacing materials, bulkhead and ceiling veneers including any adhesives used to fasten the veneers to the bulkheads and ceilings, paints, and exposed treatment of insulating materials. Note 1-This test method has been prepared to closely follow the test procedure of IMO Resolution A.653(16) (1). Optional provisions not applicable to the domestic use of this test method have been deleted. 1.2 Tests performed according to this test method are intended to yield fire properties that, when appropriately interpreted, can be used to select materials and surface treatments that will limit the rapid growth and spread of fire. 1.3 This test method requires a specific range of specimen radiant thermal exposure for measuring fire properties. 1.4 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard assessment or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

Standard Test Method for Flammability of Marine Surface Finishes

ASTM E1317-97a(2002) 船舶表面涂层易燃性的试验方法

This test method provides a means for evaluation of the flammable performance of surface finish materials used in constructing and outfitting ships. A specimen of the surface finish of concern is mounted on the support material contemplated for use and subjected to a controlled significant radiant-flux exposure. All specimens are tested while mounted in a vertical plane. The following surfaces are exposed to test: 5.4.1 Bulkhead specimens having surface veneers, fabrics, or painted finishes are tested on one or both exposed sides. 5.4.2 Ceiling finish materials shall be tested on the lower exposed surface. 5.4.3 For ceiling finish materials which are perforated and air backed, tests also shall be conducted on the back (upper) surface of the material. 5.4.4 Deck finish and flooring materials are tested on the upper exposed surface. 5.4.5 Protective membranes or finishes on insulation materials are tested on the air-exposed face or faces. This test method provides fire properties that relate to the flammability of the specimens tested. These include ignitability, heat exposure for continued burning, critical flux at extinguishment, and heat-release behavior under varying flux-exposure conditions applied. This test method does not provide: 5.6.1 Full information on fire properties of surface-finish materials supported by backing materials other than those tested. 5.6.2 Full information on surface-finish materials when used in other thicknesses than those tested. 5.6.3 Methods for using the fire property measurements as a measure for classifying the fire risk or hazard of the specimens tested. 1.1 This fire-test-response standard covers a procedure for measuring fire properties associated with flammable behavior of surface finishes used on noncombustible substrates aboard ship (Note 1). In particular, these include surface finishes intended for use in ship construction such as deck surfacing materials, bulkhead and ceiling veneers including any adhesives used to fasten the veneers to the bulkheads and ceilings, paints, and exposed treatment of insulating materials. Note 18212;This test method has been prepared to closely follow the test procedure of IMO Resolution A.653(16) (1). Optional provisions not applicable to the domestic use of this test method have been deleted.1.2 Tests performed according to this test method are intended to yield fire properties that, when appropriately interpreted, are potentially useful to select materials and surface treatments that will limit the rapid growth and spread of fire.1.3 This test method requires a specific range of specimen radiant thermal exposure for measuring fire properties.1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

Standard Test Method for Flammability of Marine Surface Finishes

CB 1286-1996 鱼雷铝合金壳体硬质阳极氧化膜层技术要求及检验方法

本标准规定了鱼雷铝合金壳体表面硬质阳极氧化膜层的外观厚度和硬度的要求及检验方法。 本标准适用于鱼雷铝合金壳体的硬质阳极氧化处理。对于鱼雷壳体以外的铝或铝合金零件的硬质阳极氧化亦可参照使用。

Technical requirements and inspection methods for hard anodized film layer of torpedo aluminum alloy shell

DIN EN 3035:1996 航空航天系列.合金钢镀镉短螺纹带翼型十字槽的100度沉头配合螺钉.等级:1100MPa(室温)/235℃

The document specifies the characteristics for screws with 100?countersunk head, offset cruciform recess, close tolerance normal shank and short thread, in alloy cadmium plated steel of tensile strength classification 1100 ?#,,#

Aerospace series - 100° countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa(at ambient temperature)/235 °C; German version EN 3035:1996

CB/T 3770-1996 船舶焊接接头维氏硬度试验方法

本标准规定了钢质船舶焊接接头维氏硬度试验的原理和仪器、试样、试验和试验结果处理。 本标准适用于钢质船舶焊接接头硬度的测定，用于焊接工艺认可、钢材焊接性能评定和焊接材料认可的硬度试验。

Vickers hardness test method for ship welded joints

CB/T 266-1996 再生锡基轴承合金锭

本标准规定了再生锡基轴承合金锭的技术要求、试验方法、检验规则以及标志、包装和贮存。 本标准适用于采用回收的锡基轴承合金碎块和切屑，经熔化、精炼、检验合格的锡基轴承合金锭。

Recycled tin-based bearing alloy ingot

NAVY MIL-R-23811 NOTICE 1-1996 MARK 64 MOD 2鱼雷训练部分的记载装置

MIL-P-23811(0!3), dated 13 March 1963, and its Amendment 3 dated 25 September 1969, are inactive for new design and are no longer used, except for replacement purposes.

RECORDER ASSEMBLY (FOR TORPEDO EXERCISE SECTION MARK 64 MOD 2)

NAVY MIL-R-21187 C NOTICE 1-1996 MARK 37 MODS 0,2,和 3鱼雷压敏继电器

MIL-R-21187C7 dated 10 January 1971 is inactive for new design and is no longer used, except for replacement purposes.

RELAY, SENSITIVE (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)

NAVY MIL-T-23824 A NOTICE 1-1996 37号0,2,3型鱼雷照明灯

MIL-T-23824A, dated 9 August 1971, and its Amendment 1, dated 4 November 1971 are inactive for new' design and are no longer used, except for replacement purposes.

TORPEDO BEACON LIGHT (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)

NAVY MIL-P-82500 A NOTICE 1-1996 MARK 37 MODS 2 和3鱼雷电源整流器

MIL-P-S2500A, dated 9 August 1971 is inactive for new design and is no longer used, except for replacement purposes.

POWER SUPPLY, RECTIFIER (FOR TORPEDO MARK 37 MODS 2 AND 3)

NAVY MIL-P-19023 D NOTICE 1-1996 MK 37 MODS 0,2,和 3鱼雷摆槌

MIL-P-l9023D, dated 19 November 1970 is inactive for new design and is no longer used, except for replacement purposes.

PENDULUM (FOR TORPEDO MK 37 MODS 0, 2, AND 3)

NAVY MIL-P-19086 E NOTICE 1-1996 MK 37 MODS 2和3鱼雷高压电源

MIL-E-50796, dated 12 June 1973, and Amendment 1, dated 10 December 1976, has been reviewed and determined to be valid for use in acquisition.

POWER SUPPLY, HIGH VOLTAGE (FOR TORPEDO MARK 37 MODS 2, AND 3)

NAVY MIL-T-19029 E NOTICE 1-1996 37号0及3型鱼雷定时器

MIL-T-l9029E, dated 27 August 1970 is inactive for new design and is no longer used, except for replacement purposes.

TIMER (FOR TORPEDO MARK 37 MODS 0 AND 3)

NAVY MIL-P-23810 A NOTICE 1-1996 MARK 64 MOD 2鱼雷实验部分仪表面板和组元逐帧录像法

MIL-P-23810A(OS), dated 7 November 1967, and its Amendment 3 dated 26 October 1970, are inactive for new design and are no longer used, except for replacement purposes.

PANEL, COMPONENT, RECORDING (FOR TORPEDO EXERCISE SECTION MARK 64 MOD 2)

NAVY MIL-G-18853 C NOTICE 1-1996 MK47MODS2,3鱼雷回转速率

MIL-G-l8853C, dated 29 August 1975 is inactive for new design and is no longer used, except for replacement purposes.

GYRO, RATE (FOR TORPEDO MARK 37 MODS 2, AND 3)

NAVY MIL-F-81154 A NOTICE 1-1996 MK37MODS 0,2,3鱼雷低通滤波器(NAVORD DWG 1563732)

MIL-F-S1154A, dated 10 September 1970 is inactive for new design and is no longer used, except for replacement purposes.

FILTER, LOWPASS (NAVORD DWG 1563732) (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)

NAVY MIL-F-81150 A NOTICE 1-1996 MK37MODS 0,2,3鱼雷带通滤波器(NAVORD DWG 1563728)

MIL-F-81150A, dated 12 October 1971 is inactive for new design and is no longer used, except for replacement purposes.

FILTER, BANDPASS (NAVORD DWG 1563728) (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)

NAVY MIL-I-19028 E NOTICE 1-1996 MK37MODS 0,2,3鱼雷逆变换装置

MIL-I-l9028E, dated 3 May 1971 is inactive forsnew design and is no longer used, except for replacement purposes.

INVERTER (FOR TORPEDO MARK 37 MODS 0, 2, AND 3)

NAVY MIL-H-22868 NOTICE 1-1996 鱼雷用70%及90%稳定过氧化氢

MIL-H-22868, dated 21 March 1961 is inactive for new design and is no longer used, except for replacement purposes.

HYDROGEN PEROXIDE, E-STABILIZED, 70% AND 90% (FOR TORPEDO USE)