共找到 1400 条与 航空、航天材料基础标准 相关的标准,共 94 页
PETROLEUM FUEL FACILITIES
PETROLEUM FUEL FACILITIES
This amendment forms a part of MIL-C-63990(AR), dated 15 February 1994, and is approved for use by the US Army Armament, Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense.
CARTRIDGE, 5.56MM, TRACER, M856
This amendment forms a part of MIL-C-9963F, dated 15 October 1976, and is approved for use by all Departments and Agencies of the Department of Defense.
CARTRIDGE, 5.56MM, BALL M193
MIL-G-I 3483B( i)(AR), dated 22 January 1968, has been reviewed and determined to be valid for use in acquisition.
GRENADE, HAND, OFFENSIVE, MK3A2 PARTS FOR
This specification is approved for use by the U.S. Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense.
CARTRIDGE, 10 GAUGE SHOTSHELL, BLANK
This Amendment forms a part of Military Specification MIL-C- 60111C, dated 15 October 1976, and is approved for use by all Departments and Agencies of the Department of Defense
CARTRIDGE, 5.56MM, TRACER, M196
This specification covers the requirements for a vegetable-type margarine for use by the Armed Forces as an item of general issue and as a component of operational rations (see 6.1).
MARGARINE, CANNED
Aerospace - Methods of test for surface protective coatings; paints, varnishes - Part 4: Testing of coatings
The methods described are used for testing of paints, varnishes and similar coating materials utilized in aircraft in delivery condition.#,,#
Aerospace - Methods of test for surface protective coatings; paints and varnishes - Part 3: Tests in as-delivered condition
In these DIN 65046 Part 1 to Part 5, internationally standardized methods of test for surface protection are summarized. They are used for examination and test of points, varnishes and similar coating materials being utilized in aircraft. This document shows the survey and identifications.
Aerospace - Methods of test for surface protective coatings; paints, varnishes - Part 1: Survey and identifications
The test conditions, test specimen and conditions of drying described in this document are used for testing paints, varnishes and similar coating materials referred to in the following as coating utilized in aircraft if reference is made to these in Technical specifications, Material Performance Sheets ot in contracts.#,,#
Aerospace - Methods of test for surface protective coatings; paints, varnishes - Part 2: Specimens, preparation of specimens, drying
The document contains general instructions as well as test and cleaning fluids and, as appropiate, the required test equipment for the resistance testing of paints, varnishes and similat coatings for aerospace use.#,,#
Aerospace - Methods of test for surface protective coatings; paints, varnishes - Part 5: Coating resistance tests
Aerospace - Test methods for surface protection - Part 6: Chemical and electroplated coatings; inactive for new design
MIL-D-82586B is hereby reinstated in an inactive for new design status.
DIRECTOR, GUN AND GUIDED MISSILE, MK 73 MOD 2 AND ASSOCIATED EQUIPMENT
MIL-W-5088L, dated 9 December 1992, is inactive for new design and is no longer used except for replacement purposes. Future design should refer to SAE-AS50881.
WIRING, AEROSPACE VEHICLE [Refer To: SAE AS 50881D, SAE AS 50881C, SAE AS 50881B, SAE AS 50881B, SAE AS 50881A, SAE AS 50881]
This CID covers the general requirements for a double coated flexible foam pressure sensitive adhesive tape in roll form wound on a core with a release liner.
TAPE, TWO SIDE PRESSURE SENSITIVE ADHESIVE, FLEXIBLE FOAM BASE (FOR USE WITH EXPLOSIVES) [Superseded: ARMY MIL-T-60394 A CANC NOTICE 1, ARMY MIL-T-60394 A (3), ARMY MIL-T-60394 A (2), ARMY MIL-T-60394 A (1), ARMY MIL-T-60394 A, ARMY MIL-T-60394]
This specification covers bullet-resistant vision blocks of two different types of construction, designed for use in combat type vehicles. In addition, this specification covers vision blocks with and without laser protection filters(see 6.1).
BLOCK, VISION: BULLET-RESISTANT (METRIC)
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Process Standards Rules for the Drafting and Presentation of Surface Treatment Standards Edition P 1
The document is applicable to one- and two-component fillers used in sandwich structures, e.g. in load introduction and edge areas, for the pupose of increasing mechanical properties. They may be used in the temperature range of between -55?and 150?
Aerospace - Potting compounds for care and edge filling for sandwich structures - Technical specification
This Commercial Item Description(CID) covers one grade of diethylphthalate for use in military explosives.
DIETHYLPHTHALATE (FOR USE IN EXPLOSIVES)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号