V13 航空与航天用非金属材料 标准查询与下载
共找到 2056 条与 航空与航天用非金属材料 相关的标准，共 138 页
本部分规定了用电感耦合等离子体(ICP)原子发射光谱仪检测航空工作液中磨损金属含量的方法。本部分适用于航空润滑油等航空工作液中磨损金属元素的检测,也可供航空工作液中的污染物、添加元素检测参照使用。
Test method for determination of wear metals in operating liquid for aviation.Part 2: Inductively coupled plasma automic emission spectrometry (ICP-AES)
- ICS
- CCS
- V13
- 发布
- 2013-01-04
- 实施
- 2013-05-01
本部分规定了用能量色散X射线荧光(EDXRF)能谱仪检测航空工作液中磨损金属及非金属含量(如Mg、Al、Si、Ti、V、Cr、Mn、Fe、Ni、Cu、Zn、Mo、Ag、Cd、Sn、Pb等)的一般要求和方法。本部分适用于航空润滑油等航空工作液中磨损金属元素的检测,也可供航空工作液中的污染物、添加元素检测参照使用。
Test method for determination of wear metals in operating liquid for aviation.Part 3: Energy dispersion X-ray fluorescence spectrometry
- ICS
- CCS
- V13
- 发布
- 2013-01-04
- 实施
- 2013-05-01
5.1 The basic material properties obtained from this test method can be used in the control of the quality of interlayers, in the theoretical equations for designing laminated transparencies, and in the evaluation of new interlayers. 1.1 This test method covers the determination of the shear strength and shear modulus of interlayer materials that are restrained by relatively high modulus plies in laminated transparencies. This test method can be used with single or multiple plies of the same interlayer materials. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials
- ICS
- 49.045 (Structure and structure elements)
- CCS
- V13
- 发布
- 2013
- 实施
This SAE Aerospace Recommended Practice (ARP) shall be limited to information about corrosion caused by fluoride offgassing of fluoropolymer-based wire insulation. It reviews published reports of corrosion caused by this phenomenon, describes scenarios where this may be a concern, mitigation options, and references a test method which can be used to evaluate wire insulations where needed.
Fluoride Offgassing in Fluoropolymer Insulations
- ICS
- 49.025.40;49.060
- CCS
- V13
- 发布
- 2012-12-19
- 实施
These o-rings typically have been used as static seals in a variety of fuels, engine oils, hydraulic oils and hydraulic fluids but usage is not limited to such applications. Each application should be considered separately. These o-rings have a typical service temperature range of -65 to +400 °F (-54 to +203 °C).
Packing, Preformed, O-Ring Molded from Perfluoroether, FFO Material
- ICS
- 49.025.40;49.080
- CCS
- V13
- 发布
- 2012-12-03
- 实施
Aerospace series - NF L standardized rubber materials - Technical specification
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-12-01
- 实施
- 2012-12-21
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves, requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both.
Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistant 65-75
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-12-01
- 实施
Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 4: Acceptance criteria; German and English version EN 4050-4:2012
- ICS
- 49.025.05;49.025.15
- CCS
- V13
- 发布
- 2012-12
- 实施
This specification covers polythioether rubber fuel resistant sealing compounds supplied as a two component system which cures at room temperature. This product has been used in aircraft integral fuel tanks for repair of fillet and fastener seals and faying surface seals as well as initial sealing of faying surfaces, overcoating of fasteners, and sealing of seams and joints, for service from -80 to +320°F (-62 to +160°C), with short-term recurring exposures (approximately six hours) up to 360°F (182°C), but usage is not limited to such applications. This product is not recommended for use on aircraft windshields or canopies or other applications where crazi
Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-11-20
- 实施
This specification covers a polysulfide sealing compound with low adhesive strength. This elastomeric compound shall be supplied as a two-component system which cures at room temperature. This compound has been used typically for sealing aircraft access doors and accessories where gaskets are required, but usage is not limited to such applications. The sealing compounds are resistant to jet fuels and high aromatic aviation gasolines and are usable from -65 to 250 degrees F (-54 to 120 degrees C).
Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-11-20
- 实施
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This document details the technical requirements to be used in the evaluation of materials and processes developed for use in stripping organic finishes from fixed wing commercial aircraft. The requirements herein are intended to ensure that the materials and processes used are not detrimental to the commercial aircraft when used as specified. These requirements are not intended to judge performance of the stripping method.
Paint Stripping of Commercial Aircraft - Evaluation of Materials and Process
- ICS
- 49.040
- CCS
- V13
- 发布
- 2012-11-08
- 实施
Aerospace series - Rubber materials - Non fitted products - Storage limit time
- ICS
- 49.025.40;83.060
- CCS
- V13
- 发布
- 2012-11-01
- 实施
- 2012-11-03
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Low temperature resistant - Hardness 60 IRHD; German and English version FprEN 3697:2012
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-10-01
- 实施
Aerospace series - Non-metallic materials - Anaerobic polymerisable compounds - Threadlocking - Torque strength 19 Nm; German and English version of FprEN 4492:2012
- ICS
- 49.025.50
- CCS
- V13
- 发布
- 2012-10-01
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Low temperature resistant - Hardness 70 IRHD; German and English version FprEN 3698:2012
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-10-01
- 实施
Aerospace series - Chloroprene rubber (CR) - Heat resistance - Hardness 60 IRHD.
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-10-01
- 实施
- 2012-10-05
Aerospace series - Paints and varnishes - Cold curing intermediate coat.
- ICS
- 49.040
- CCS
- V13
- 发布
- 2012-10-01
- 实施
- 2012-10-12
Aerospace series - Non-metallic materials - Anaerobic polymerisable compounds - Threadlocking - Torque strength 2 Nm; German and English version FprEN 4488:2012
- ICS
- 49.025.50
- CCS
- V13
- 发布
- 2012-10-01
- 实施
Aerospace series - Non-metallic materials - Anaerobic polymerisable compounds - Threadlocking - Torque strength 16 Nm; German and English version FprEN 4491
- ICS
- 49.025.50
- CCS
- V13
- 发布
- 2012-10-01
- 实施
Aerospace series - Cellular elastomeric materials, open and closed cells - Semi-finished products and moulded parts - Technical specification; Text in German and English; Inactive for new design
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2012-10
- 实施
