V18 冷加工工艺 标准查询与下载

NF L06-826:1988 航空航天工业.喷丸介质.圆铸钢丸

Aerospace industry. Blast media. Round cast steel shot.

HB 6168-1988 光滑工件镀覆前尺寸

本标准规定了有配合功能要求的金属光滑工件镀覆前加工尺寸公差和加工极限偏差。 　　本标准适用下列范围： 　　a.基本尺寸 至500mm； 　　b.镀覆层厚度 3～5，5～8，8～12，12～18μm； 　　c.轴公差带 g6，h6，n6，（r6），s6，f7，h7，（h8），d9，f9，h9，（h10），c11，h11； 　　d.孔公差带 H7，K7，N7，H8，H9，（H10），H11； 　　e.配合付〔g〕

Dimensions of smooth workpiece before plating

NF L06-823:1988 航空航天工业.喷丸介质.玻璃珠

Aerospace industry. Blast media. Glass beads.

AECMA PREN 3220-1988 航空航天系列.抗热镍基合金Ni-P101HT) 冷锻变软棒材和线材用于 持续锻造或取出扣件直径3小于或等于直径D小于或等于30 mm

This standard specifies a test method to determine the adhesion of metallic coatings by shearing action. It applies to coatings with a hardness. It shall a applicable whenever referenced.

Aerospace Series Heat Resisting Nickel Base Alloy (Ni-P101HT) Cold Worked and Softened Bar and Wire for Continuous Forging or Extrusion for Fasteners 3 Less Than or Equal to D Less Than or Equal to 30 mm Issue P 1

AECMA PREN 3219-1988 航空航天系列.抗热镍基合金Ni-P101HT) 冷锻变软棒材和线材用于 持续锻造或取出扣件3小于或等于直径D小于或等于30 mm

This standard specifies the dimensions, tolerances, required characteristics and mass of a retaining washer for use in fuselage interior equipment and structural applications. This standard shall be used in conjunction with stud per EN 6088 and circlip per EN 6091.

Aerospace Series Heat Resisting Nickel Base Alloy (Ni-P101HT) Cold Worked and Softened Bar and Wire for Continuous Forging or Extrusion for Fasteners 3 Less Than or Equal to D Less Than or Equal to 30 mm Issue P 1

AECMA PREN 2960-1988 航空航天系列抗热镍基合金Ni-P100HT扣件加工冷锻和溶液处理棒材3mm 小于或等于直径D小于或等于50mm

This "Aerospace Series" Prestandard has been drawn up under the responsibility of ASD-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.

Aerospace Series Heat Resisting Nickel Base Alloy (NI-P101HT) Cold Worked and Solution Treated Bar for Machining for Fasteners 3 Less Than or Equal to D Less Than or Equal to 50 mm Issue P 1

AECMA PREN 2959-1988 航空航天系列抗热镍基合金Ni-P100HT扣件加工冷锻和溶液处理棒材3mm 小于或等于直径D小于或等于50mm

This standard specifies the characteristics of self-locking, floating, self-aligning, two lug anchor nuts, in alloy steel, cadmium plated, Mos2 lubricated.

Aerospace Series Heat Resisting Nickel Base Alloy (NI-P1O1HT) Solution Treated and Cold Worked Bar for Hot Upset Forging for Fasteners 3 Less Than or Equal to D Less Than or Equal to 30 mm Issue P 1

NF L06-825:1988 航空航天工业.喷丸介质.铸钢丸

Aerospace industry. Blast media. Grit cast steel shot.

NF L06-822:1988 航空航天工业.喷丸介质.石英砂

Aerospace industry. Blast media. Quartz.

AECMA PREN 2701-1988 航空和航天系列(2024)合金溶液处理,水淬 冷处理,自然老化冷拉结构用管材6mm小于或等于直径D小于或等于12mm

This standard has been drawn up under the responsibility of AECMA.

Aerospace Series Aluminium Alloy (2024) Solution Treated, Water Quench, Cold Worked and Naturally Aged (T3) Drawn Tube for Structures 0,6 Less Than or Equal to a Less Than or Equal to 12,5 mm Edition 1

AECMA PREN 2700-1988 航空和航天系列(6061) 合金溶液处理,水淬,冷处理和人工老化冷拉结构用管材6mm小于或等于直径D小于或等于12mm

This standard has been drawn up under the responsibility of AECMA. It will be submitted as a draft European Standard to CEN for final vote.

Aerospace Series Aluminium Alloy (6061) Solution Treated, Water Quench and Artificially Aged (T6) Drawn Bar 6 Less Than or Equal to D Less Than or Equal to 75 mm with Coarse Peripheral Grain Control Edition 1

AECMA PREN 2815-1988 航空和航天系列钢 FE-PM64 退火处理和沉淀加固棒材 Rm≥960MPa直径D小于或等于200mm

This ?Aerospace Series? pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned AECMA Commission following comment by the Member countries.

Aerospace Series Steel FE-PM64 Solution Annealed and Precipitation Hardened 960 Less Than or Equal to Rm Less Than or Equal to 1070 MPa Bar for Machining De Less Than or Equal to 200 mm Issue P 1

AECMA PREN 2952-1988 航空航天系列镍基合金(Ni-P1OOHT)热敦锻加工冷锻和溶液处理棒材3mm小于或等于直径D小于或等于30mm

This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258.

Heat Resisting Nickel Base Alloy (Ni-P1OOHT) Solution Treated and Cold Worked Bar for Hot Upset Forging for Fasteners 3 Less Than or Equal to D Less Than or Equal to 30 mm

AECMA PREN 3120-1988 航空航天系列.钛合金TI-P69 冷锻2级锻件溶液或沉积处理690MPa小于或等于Rm小于或等于1030MPa

This ?Aerospace Series? pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned AECMA Commission following comment by the Member countries.

Aerospace Series Titanium Alloy TI-P69 Cold Worked and Stress Relieved 690 Less Than or Equal to Rm Less Than or Equal to 1030 MPa Seamless Tube for Pressure System D Less Than or Equal to 50 mm Issue P 1

AECMA PREN 2961-1988 航空航天系列抗热镍基合金Ni-P100HT扣件加工冷锻和溶液处理棒材3mm小于或等于直径D小于或等于50mm

This standard specifies the requirements for bar and wire to be used for the manufacture of machining fasteners for aerospace applications.

Heat Resisting Nickel Base Alloy (Ni-P100HT) Cold Worked and Solution Treated Bar for Machining for Fasteners 3 Less Than or Equal to D Less Than or Equal to 50 mm

DIN 65350-2:1988 航空和航天.铆接.盲铆钉用铆接工具的装配可达性

Aerospace; riveting; assembly accessibility of riveting tools for blind rivets

DIN 65350-1:1988 航空航天.铆接.第1部分:实心铆钉用铆接工具铆接组件的可达性

This standard contains specifications pertinent to manufacture and use such as dimensions and designation, material, surface treatment, marking and technical specifications.#,,#

Aerospace; riveting; assembly accessibility of riveting tools for solid rivets

DIN 65350-4:1988 航空和航天.铆接.紧公差铆钉用铆接工具的装配可达性

Aerospace; riveting; assembly accessibility of riveting tools for close tolerance rivets

DIN 65350-3:1988 航空和航天.铆接.带螺纹盲铆钉用铆接工具的装配可达性

This standard contains specifications pertinent to manufacture and use such as dimensions and designation, material, surface treatment, marking and technical specifications.#,,#

Aerospace; riveting; assembly accessibility of riveting tools for threaded blind rivets

AECMA PREN 3343-1988 航空航天系列.铝合金(7010)冷拉或挤压棒和型材a或直径D小于或等于150 mm

This

Aerospace Series Aluminium Alloy (7010) Solution Treated and Artificially Aged (T76511) Extruded Bars and Sections 1 Less Than (a or D) Less Than or Equal to 130 mm with Peripheral Coarse Grain Control Issue P 1