V39 燃油系统及其附件 标准查询与下载

NAVY MIL-DTL-85470 B VALID NOTICE 1-2004 抑制剂,结冰,燃油系统,高闪光北约冷战数S - 1745(取消的MIL - DTL - 27686)

MIL-DTL-85470B, dated 15 June 1999, has been reviewed and determined to be valid for use in acquisition

INHIBITOR, ICING, FUEL SYSTEM, HIGH FLASH NATO COLD NUMBER S-1745 (CANCELLING MIL-DTL-27686) [Replaced: AIR FORCE MIL-DTL-27686 G CANC NOTICE 2, AIR FORCE MIL-DTL-27686 G NOTICE 1, AIR FORCE MIL-DTL-27686 G, AIR FORCE MIL-I-27686 F, AIR FORCE MIL-I-

ASHRAE 4741-2004 石油流通观察员,估算冷媒压缩机中的含油浓度和石油量

An Oil Circulation Observer for Estimating Oil Concentration and Oil Amount in Refrigerant Compressors

An Oil Circulation Observer for Estimating Oil Concentration and Oil Amount in Refrigerant Compressors

NAVY MIL-PRF-24751 A-2004 海军军舰上用风向标轴向气体涡轮围栏冷却鼓风机

Scope. This specification covers high pressure and HI shock, type TA vaneaxial fans for use in cooling the gas turbine enclosures of ship propulsion/generator systems.

FANS, VANEAXIAL GAS TURBINE ENCLOSURE COOLING NAVAL SHIPBOARD

SAE AIR5693-2004 航空航天用带标准液的PTFE软管组件的可混用性

The scope of this document is limited to the compatibility of typical fluids that may come in contact with PTFE hose assemblies. PTFE hose assemblies may be braided with CRES wire, polyester or para-aramid fibers. Hose assemblies may be equipped with aluminum, CRES, titanium or nickel alloy fittings; and with fire resistant cover materials. All of these constituent materials of PTFE hose assemblies must be compatible with all of the fluids found in any particular application.

Compatibility of PTFE Hose Assemblies With Typical Fluids Found in Aerospace Applications

NAVY MIL-P-17689 NOTICE 3-2003 N-5型双基极片状推进剂

MIL- P-17689, dated 30 July 1953, is hereby reactivated and may be used for either new or existing design acquisition.

PROPELLANT, DOUBLE-BASE SHEET, TYPE N-5

HB 8072-2002 油箱注油口盖规范

本规范规定了飞机油箱注油口盖(简称口盖)的技术要求 ，质量保证规定和交货准备。 本规范适用于飞机油箱注油口盖的制造和验收。

Specification of cover for fuel tank refuel

HB 8071-2002 油箱注油口盖

本标准规定了油箱注油口盖的结构、尺寸要求。 本标准适用于油箱密封口的口盖。

Cover for fuel tank refuel

SAE ARP598C-2003 (R)液体动力系统的航空显微镜粒度法和微粒子污染

This SAE Aerospace Recommended Practice (ARP) defines the materials, apparatus and procedure for sizing and counting of particulate contamination, 5 鎚 or greater, in hydraulic fluid samples by membrane filtration iwth microscopic counting. It is capable of counting particulate matter in samples withdrawn from fluid power systems as identified by the 12 classes of SAE AS 4059 or NAS 1638 and projected beyond these for the five standard ranges specified and can thus serve as the primary document to determine acceptability. It is also capable of revealing but not measuring evidence of abnormal amount of water, other fluids, fine particulate and other materials, especially fibers and metals. It is applicable to all military, civil, space vehicles and test equipment.

(R) Aerospace Microscopic Sizing and Counting of Particulate Contamination for Fluid Power Systems

SAE ARP5298-2003 飞机燃油补给口磨损限值

This SAE Aerospace Recommended Practice (ARP) defines the wear limits allowed on certain features of pressure fuel servicing adapters which are crucial for safe interfacing of pressure fuel servicing nozzles and pressure caps. Wear limits as described herein represent the maximum amount of wear on certain features of the adapter beyond which use of the adapter for these purposes may contribute to an unsafe condition. Such wear is the result of the normal use of the adapter for aircraft refueling and also, in some cases, for nozzle stowage on refueling vehicles.

Aircraft Fueling Adapter Wear Limits

ARMY A-A-59402 VALID NOTICE 1-2003 鼓(散装推进剂)

A-A-59402, dated 25 January 1999, has been reviewed and determined to be valid for use in acquisition

DRUM (FOR BULK PROPELLANT)

ISO 7314:2002 航空航天.液压系统.金属软管组件

This International Standard gives specifications for medium pressure, high temperature, flexible metal hose assemblies suitable for continuous operation in liquid and pneumatic systems from - 55 ℃ to + 400 ℃, with short duration excursions up to + 650 ℃. The hose assemblies covered by this International Standard are intended for use in aerospace applications for conveying air and other gases in pneumatic systems, bleed air systems, heating and ventilating systems and instrument air systems when used at pressures and temperatures within the limits laid down in Tables 2 and 3. This International Standard does not cover flow velocity in such assemblies exceeding 54 m/s; higher velocities require special vibration-dampening devices. Hose assemblies supplied to the specifications laid down in this International Standard may be of two types: — Type 1: Convoluted inner tube - welded, of moderate mass and moderate flexibility. — Type 2: Convoluted inner tube - seamless or butt-welded and redrawn, of low mass and high flexibility.

Aerospace - Fluid systems - Metal hose assemblies

NAVY MIL-T-24797 NOTICE 3-2002 光纤转速计的一般规格 (海军舰载使用)(十进制)

MIL-T-24797, dated 22 June 1995, with Notice 2, dated 9 August 2002, is inactive for new design and is no longer used, except for replacement purposes. Future acquisition for this material should refer to ASTM F2046, "Standard Specification for Tachometers, Various."

TACHOMETERS, FIBER OPTIC, (NAVAL SHIPBOARD USE), (METRIC), GENERAL SPECIFICATION FOR

NAVY MIL-STD-2042-1 B-2002 海军舰光缆拓扑装置标准方法(电缆)

This Department of Defense Standard Practice is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (CABLES) (PART 1 OF 7 PARTS)

NAVY MIL-STD-2042-3 B-2002 海军舰光缆拓扑装置标准方法(电缆侵入)

This method identifies MCP insert block sizes used to pass optical fiber cables through decks and bulkheads. The methods for installation of the MCP and insert blocks is the same as those specified for electrical cables in MIL-STD- 2003-3. These installation methods are not repeated in this standard practice but they are identified in paragraph 5 in this part of this standard practice.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (CABLE PENETRATIONS) (PART 3 OF 7 PARTS)

NAVY MIL-STD-2042-4 B-2002 海军舰光缆拓扑装置标准方法

This standard practice provides detailed methods for installing optical fiber cable cableways and cable protection on surface ships and submarines.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (CABLEWAYS) (PART 4 OF 7 PARTS)

NAVY MIL-STD-2042-7-2002 海军舰光缆拓扑装置标准方法(连接电缆装置和通信硬盘)

This standard practice provides detailed methods for installing pierside connectivity fiber optic cable assemblies and interconnection hardware.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (PIERSIDE CONNECTIVITY CABLE ASSEMBLIES AND INTERCONNECTION HARDWARE)

NAVY MIL-STD-2042-6 B-2002 海军舰光缆拓扑装置标准方法(测试)

This standard practice provides detailed methods for testing optical fiber cable installations.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (TESTS) (PART 6 OF 7 PARTS)

NAVY MIL-STD-2042-5 B-2002 海军舰光缆拓扑装置标准方法(插件和联络线)

This Department of Defense Standard Practice is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (CONNECTORS AND INTERCONNECTIONS) (PART 5 OF 7 PARTS)

NAVY MIL-STD-2042B-2002 海军舰光缆拓扑装置标准方法

This standard provides detailed methods for the installation and test of fiber optic cabling and associated components (see 3.2) on Naval surface ships and submarines.

FIBER OPTIC TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS

NAVY MIL-STD-2042-2 B-2002 海军舰光缆拓扑装置标准方法(设备)

This method describes the procedures for sealing the ends of empty BOF tubes in tube routing boxes, fiber optic interconnection boxes and equipment.

FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR NAVAL SHIPS (EQUIPMENT) (PART 2 OF 7 PARTS)