W57 纺织复制品 标准查询与下载

NF G33-003*NF EN 13569:2002 舱室用滚轴毛巾.性能要求和加工

Cabinet roller towels - Performance requirements and processing.

ASTM D4037-02(2008) 机织、针织或植绒床罩织物的标准性能规范

Fabrics intended for this end-use should meet all of the requirements listed in Table 1. It should be recognized that fabrics can be produced with an almost infinite number of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test emthods are discussed in the appropriate sections of the specified test methods. TABLE 1 Specification Requirements Note8212;Class for colorfastness and DP rating is based on a numerical scale of 5 for negligible or no color change, color transfer, or wrinkle to 1 for very severe color change, color transfer, or wrinkle. The numerical rating in Table 1 or a higher numerical rating is acceptable. Characteristic Requirements Section Woven Knit Breaking strength force (load)25 lbf (111 N) min. . . 5.1 Bursting strength. . .35 psi (241 kPa) min 5.2 Tear strength1.5 lbf (6.7 N) min 5.3 Dimensional change: Laundering and dry cleaning (each direction): 5.4.1–5.4.2 5.4.2 Tailored type±3.5 % max±5.0 % max Throw type±5.0 % max±5.0 % max

Standard Performance Specification for Woven, Knitted, or Flocked Bedspread Fabrics

ASTM D4912-02 乙烯基涂覆玻璃丝防昆虫(蚊帐)布和百页窗帘布织物稳定性的标准试验方法

This test method is considered satisfactory for acceptance testing of commerical shipments since the method has been used extensively in the trade for acceptance testing. 5.1.1 In cases of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Studentrsquo;t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing begins. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias. Vinyl-coated glass yarn insect screening and louver cloth are subjected to a heating process to fuse the warp yarns to the filling yarns of the woven structure. The force at which yarns in one direction move over yarns in the opposite direction is a measure of the bond of fusion. The degree of the bond of fusion on the vinyl-coated glass yarn insect screening and louver cloth is used for process control. Fabric stability was formerly called resistance to yarn slippage.1.1 This test method provides a procedure for evaluating fabric stability by measuring the resistance to yarn slippage of filling yarns over warp yarns, or warp yarns over filling yarns in vinyl-coated glass yarn insect screening and louver cloth.1.2 This test method shows the values in both SI units and inch-pound units. "SI units" is the technically correct name for a system of metric units known as the International System of Units. "Inch-pound units" is the technically correct name for the customary units used in the United States. The values expressed in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Fabric Stability of Vinyl-Coated Glass Yarn Insect Screening and Louver Cloth

ASTM D4113-02(2008) 机织家具套织物的标准性能规范

Fabrics intended for this end-use should meet all of the requirements listed inTable 1 . It should be recognized that fabrics can be produced with an almost infinite number of combination of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in slipcovers. 1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven Slipcover Fabrics

ASTM D4847-02 机织遮阳篷和遮雨檐织物的标准规范

1.1 This performance specification covers woven awning and canopy fabrics composed of any textile fiber or mixture of fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Woven Awning and Canopy Fabrics

ASTM D3691-02 机织带状针织家用窗帘和带皱折编织物的标准性能规范

1.1 This performance specification covers the requirements for all knit, lace, foam back, stitch-bonded, conventional weights, and sheer woven fabrics to be used in the manufacture of curtains and draperies. 1.2 This performance specification is not applicable to fabrics made of glass. 1.3 For those properties where fabric direction is pertinent, these requirements apply to the length and width directions for woven fabric and to both the wale and course directions for knit fabric. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven, Lace, and Knit Household Curtain and Drapery Fabrics

ASTM D4847-02(2008) 机织遮阳篷和遮雨檐织物的标准规范

Fabrics intended for this end-use should meet all of the requirements listed in Table 1. It should be recognized that fabrics can be produced with an almost infinite number of combinations of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finished.) Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers woven awning and canopy fabrics composed of any textile fiber or mixture of fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven Awning and Canopy Fabrics

ASTM D4037-02 机织、针织或植绒床罩织物的标准性能规范

1.1 This performance specification covers the performance requirements for woven, knitted, or flocked fabrics to be used in the manufacturing of bedspreads.1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven, Knitted, or Flocked Bedspread Fabrics

ASTM D4111-02 家用和单位用机织台布和桌布织物的标准性能规范

1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven Napery and Tablecloth Fabrics Household and Institutional

ASTM D4113-02(2013) 机织家具套织物的标准性能规格

5.1 Fabrics intended for this end-use should meet all of the requirements listed inTable 1 . 5.2 It should be recognized that fabrics can be produced with an almost infinite number of combination of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. 5.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. 5.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. 1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in slipcovers. 1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Woven Slipcover Fabrics

DIN EN 13569:2001 舱室用滚轴毛巾.性能要求和加工

Cabinet roller towels - Performance requirements and processing; German version EN 13569:2001

BS EN 13569:2001 舱室用滚动抹布.加工和性能要求

This Standard specifies requirements for the following: a) Three categories of cabinet towel, the categories being defined in terms of mass per unit area and tensile strength of the fabric; certain constructional and performance requirements are also covered. b) Process validation procedures to ensure that cabinet towels achieve the condition of hygienic cleanliness in processing. It also contains informative annexes containing the following: - an example of suitable fabric structure, - recommendations for the care, use and transportation of cabinet towels after processing, - examples of key process variables for disinfection, - the preparation and application of bioindicators for the validation of the process to achieve hygienic cleanliness. The colour fastness to washing test and the requirement level are based on the assumption that chlorine bleaching treatments will not be used in laundering.

Cabinet roller towels. Performance requirements and processing

JIS L 4403:2000 卧具（Futon 蒲团）

この規格は，既裂のふとんについて規定する。

Futon

JIS L 4105:2000 浴巾

この規格は，純綿でループバイルの浴用タオル()(以下，タオルという。)について規定する。

YOKUYO Towel

JIS L 4212:2000 防水床单

この規格は，繊維製防水シーッ(以下，防水シーツという。) ()について規定する。

Water proof bed sheets

NF G91-110*NF EN 12241:1999 搭扣.水洗、干燥或干洗前的锁紧方法

Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning.

NF G91-111*NF EN 12242:1999 搭扣.剥离强度的测定

Touch and close fasteners - Determination of peel strength.

JIS L 1915:1998 蒲团(FUTON)湿度传导特性的试验方法

この規格は，寝具として用いるふとんの水分移動持性を評価する試験方法について規定する。

Test methods of humidity transfer characteristics of FUTON

JIS L 1914:1998 蒲团(FUTON)弹性的试验方法

この規格は，寝具として用いるふとんの弾力性を評価する試験方法について規定する。

Test methods of elasticity of FUTON

BS 1877-10:1997 家用床上用品.童床,摇篮童车及类似家用物品规范

Does not cover mattresses with loose fillings (i.e. bean bag type) or mattresses with covers which are not level and can form pockets (i.e. button down type).

Domestic bedding. Specification for mattresses and bumpers for children's cots, perambulators and similar domestic articles