Y81 家具制品 标准查询与下载

NF S54-065:2013 儿童使用和保健条款.椅安装座

Child use and care articles - Chair mounted seat

DB13/T 1685-2012 学生公寓多功能家具安装质量技术要求

本标准规定了学生公寓多功能家具的术语、定义、分类、要求、检验方法及检验规则。本标准适用于学生公寓多功能家具的安装质量。其它用于学生公寓的家具可参照执行。

Technical requirements for installation quality of multifunctional furniture in student apartments

DIN EN 1957:2013 家具. 床和床垫. 测定功能特征和评估标准的试验方法; 德文版本EN 1957-2012

This European Standard specifies test methods for the determination of the durability and hardness of mattresses and all types of fully erected beds with mattresses (and mattress pads when they form a unit with the mattress). It does not apply to water beds,air beds and children cots.

Furniture.Beds and mattresses.Test methods for the determination of functional characteristics and assessment criteria; German version EN 1957:2012

ASTM F1169-13 实际大小的婴儿床的标准消费者安全规范

1.1 This consumer safety specification establishes performance requirements and test procedures to determine the structural integrity of full-size cribs. It also contains design requirements addressing entanglement on crib corner post extensions, and requirements for warning labels and instructional material. It also covers bassinet, changing table, or similar accessories to a crib that when in the manufacturer’s recommended use position are in the occupant retention area. These accessories shall also comply with the applicable requirements of the ASTM International standards addressing those accessories. For example, a changing table that attaches to a crib shall also comply with the applicable requirements in Consumer Safety Specification F2388. This specification does not cover inflatable products. 1.2 No crib produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Full-Size Baby Cribs

ASTM F1821-13 幼儿床的标准消费品安全规范

1.1 This consumer safety specification covers requirements for the design and performance of toddler beds. It also contains requirements for labeling and instructional material. 1.2 This consumer safety specification is intended to minimize incidents to children resulting from normal use and reasonably foreseeable misuse of toddler beds. It does not address incidents resulting from alteration or unreasonable misuse. 1.3 For the purposes of this consumer safety specification, a toddler bed is a bed that is sized to accept a full-size crib mattress and is intended for use by a child not less than 15 months of age and who weighs no more than 50 lb (27.7 kg). 1.4 No toddler bed produced after the approval date of this consumer safety specification shall indicate compliance with this specification, either by label or by other means, unless it conforms to all the requirements contained herein. 1.5 This consumer safety specification includes the following sections: Scope Section 1 Referenced Documents Section 2 Terminology Section 3 Calibration and Standardization Section 4 General Requirements Section 5 Performance Requirement Section 6 Test Methods Section 7 Marking and Labeling Section 8 Instructional Literature Section 9 Keywords Section 10

Standard Consumer Safety Specification for Toddler Beds

ASTM F406-13 非实际大小的婴儿床/玩耍场地的标准消费者安全规范

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard. 1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products. 1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1—This consumer safety specification includes the following sections: Title Section Scope

Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

ASTM F2933-13 婴儿床垫的标准消费者安全规范

1.1 This consumer safety specification establishes design requirements, testing requirements and methods, and requirements for labeling for full-size and non-full-size crib mattresses. 1.2 No crib mattress produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Crib Mattresses

ASTM F404-13 高脚椅的标准消费品安全规范

1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair. 1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age. 1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination. 1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—This consumer safety specification includes the following sections: Title Section Scope

Standard Consumer Safety Specification for High Chairs

ASTM F404-13a 高脚椅的标准消费品安全规范

1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair. 1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age. 1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination. 1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—This consumer safety specification includes the following sections: Title Section Scope

Standard Consumer Safety Specification for High Chairs

ASTM F2906-13 床边婴儿床的标准消费品安全规范

1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of bedside sleepers. 1.2 This consumer safety specification is intended to minimize the risk of injury to an infant from the normal use and reasonably foreseeable misuse of a bedside sleeper. 1.3 This consumer safety performance specification covers products intended to provide sleeping space for an infant up to approximately 5 months of age (or when child begins to push up on hands and knees). These products are intended to be secured to the side of an adult bed for the purpose of having a baby sleep in close proximity to an adult. 1.4 No bedside sleeper produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein. 1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care provider. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 6 of this consumer safety performance specification. This standard may involve the use of hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Bedside Sleepers

ANSI/ASTM E1822:2013 折叠椅着火试验方法

Test Method for Fire Testing of Stacked Chairs

ASTM E1590-13 床垫着火试验的标准试验方法

5.1 This test method provides a means of measuring a variety of fire-test-response characteristics resulting from burning a test specimen, mattress or mattress with foundation. After ignition using a propane gas burner, the test specimen is permitted to burn freely under well-ventilated conditions. The most important fire-test-response characteristic measured in this test method is the rate of heat release, which quantifies the intensity of the fire generated. 5.2 The rate of heat release is measured by the principle of oxygen consumption. Annex A3 discusses the assumptions and limitations. 5.3 This test method also provides measures of other fire-test-response characteristics, including smoke obscuration (as the rate of smoke release, total smoke released, or optical density of smoke), combustion gas release (as concentrations of combustion gases), and mass loss, which are important to making decisions on fire safety. 5.4 In the majority of fires, the most important gaseous components of smoke are the carbon oxides, present in all fires. They are indicators of the toxicity of the atmosphere and of the completeness of combustion. Measurement of concentrations of carbon oxides are useful for two purposes: (1) as part of fire hazard assessment calculations and (2) to improve the accuracy of heat release measurements. Other toxic combustion gases, which are specific to certain materials, are also indicators of the toxicity of the atmosphere, but are less crucial for determining combustion completeness and are optional measures; however, fire hazard assessment often requires their measurement. 5.5 The type of ignition chosen (flaming source) is common in both accidental and intentional fires in public occupancies. The test method is thus applicable to mattresses in public occupancies. Such facilities include, but are not limited to, health-care facilities, old age convalescent and board and care homes, and college dormitories and residence halls. 5.6 One of the following three configurations is to be used in this test method: 5.6.1 Test Configuration A—A test room with the following dimensions: 3.66 by 2.44 by 2.44 m (12 by 8 by 8 ft) high. 5.6.2 Test Configuration B—A test room with the following dimensions: 3.66 by 3.05 by 2.44 m (12 by 10 by 8 ft) high. 5.6.3 Test Configuration C—An open calorimeter (or furniture calorimeter). 5.7 Rooms of other dimensions are acceptable where it has been shown that equivalent test results are obtained. 5.8 Measurements in the three test configurations listed in 5.6 have been shown to give similar results for heat release in the duct, and mass loss, up to a rate of heat release of 600 kW (

Standard Test Method for Fire Testing of Mattresses

ASTM F1427-13 双层床的标准消费者安全规范

1.1 This consumer safety specification establishes minimum requirements for the design and performance of bunk beds. It also contains requirements for labeling and instructional material. 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of bunk beds. This consumer safety specification is written within the current state of the art of bunk bed technology and does not address bunk beds that are blatantly misused or are used in a careless manner that disregards warning statements and safety instructions provided with each bunk bed. 1.3 For the purpose of this consumer safety specification, a bunk bed (hereinafter referred to as a bed) is defined as any structure that includes at least one sleeping surface in which the underside of any of its foundations is over 30 in. (762 mm) from the floor. 1.4 This consumer safety specification does not address bunk beds for institutional use (for example, in prisons, military facilities, dormitories, and so forth). 1.5 The values stated in inch-pound units, as well as any specified ISO/ANSI standard hardware, are to be regarded as the standard. The values given in parentheses are for information only. 1.6 The following safety hazards caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Bunk Beds

ANSI/ASTM E1537:2013 软垫家具着火测试的试验方法

Test Method for Fire Testing of Upholstered Furniture

KS G 4213-2012 户外用长椅

이 표준은 정원, 공원, 공공 장소 등에서 3인 이상이 휴식에 사용하는 고정식 옥외용 벤치

Benches for out of door

KS G 2020-2012 收纳道具

이 표준은 수납 가구(이하 수납 가구라 한다.)에 대하여 규정한다.

Storage furniture

QB/T 1952.1-2012 软体家具.沙发

本标准规定了沙发的术语和定义、产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于室内使用的沙发。当有具体的产品标准时，应符合相关产品标准的规定。

Upholstered furniture.Sofa

NF S54-007-1:2012 儿童高脚椅.第1部分:安全性要求

Children's high chairs - Part 1 : safety requirements.

NF S54-007-2:2012 儿童高脚椅.第2部分:试验方法

Children's high chairs - Part 2 : test methods.

DIN EN 14988-2:2012 儿童高脚椅. 第2部分:试验方法; 德文版本EN 14988-2-2006+A1-2012

This European Standard specifies test methods for the assessment of the requirements of children's high chairs.

Children's high chairs - Part 2: Test methods; German version EN 14988-2:2006+A1:2012