Z60 污染物排放综合 标准查询与下载

DB41/ 684-2011 铅冶炼工业污染物排放标准

Pollutant Discharge Standards for Lead Smelting Industry

DB44/ 27-2001 大气污染物排放限值

本标准分年限规定固定污染源的37钟大气污染物排放限值，同时规定执行标准中的各种要求。 本标准适用于广东省境内除恶臭物质、汽车、摩托车、工业炉窑、炼焦炉、危险废物焚烧、生活垃圾焚烧、饮食业等行业现有污染源大气污染物的排放管理、建设项目环境影响评价、建设项目环境保护设施设计、竣工验收及其投产后的排放管理。 本标准表1、表2适用于各种工艺废气。 本标注表3、表4适用于各种用于发电的煤粉锅炉及单台出力在65t/h以上的循环流化床发电锅炉、燃油、燃气发电锅炉。 本标准表5、表6、表7、表8适用于除煤粉发电锅炉和单台出力在65t/h以上的沸腾、燃油、燃气发电锅炉以外的各种容量和用途的燃煤、燃油、燃气锅炉，使用甘蔗渣、锯末、稻壳、树皮等燃料的锅炉，参照燃煤锅炉大气污染物最高允许排放浓度执行。 本标准表9、表10、表11适用于水泥厂。

Emission limits of air pollutants

DIN EN ISO 25139:2011 固定源排放.气相色谱测定甲烷浓度方法手册(ISO 25139-2011).德文版本EN ISO 25139-2011

This European Standard specifies a manual method for the determination of the concentration of methane emissions from stationary sources . This International Standard specifies an independent method of measurement, which is validated for mass concentrations up to 1500 mg/m.

Stationary source emissions - Manual method for the determination of the methane concentration using gas chromatography (ISO 25139:2011); German version EN ISO 25139:2011

DB34/ 1445-2011 在用压燃式发动机汽车加载减速法排气烟度排放限值

Limits for exhaust smoke from in-use vehicl equipped with compression ignition engine under lug-down test

NF X30-366*NF ISO 14066:2011 温室气体.温室气体评估小组和验证团队的能力要求.

Greenhouse gases - Competence requirements for greenhouse gas validation teams and verification teams.

BS EN ISO 25139:2011 固定源排放.用气相色谱测定甲烷浓度的手工方法

This International Standard specifies a manual method for the determination of the concentration of methane emissions from stationary sources. This International Standard specifies an independent method of measurement, which is validated for mass concentrations up to 1 500 mg/m. NOTE 1 An independent method of measurement is used for such purposes as calibration or validation of permanently installed measuring systems. NOTE 2 An “independent method of measurement” is termed “standard reference method (SRM)” in EN 14181.

Stationary source emissions. Manual method for the determination of the methane concentration using gas chromatography

BS ISO 11057:2011 空气质量.可清洗过滤介质过滤特性的试验方法

Air quality. Test method for filtration characterization of cleanable filter media

BS ISO 14066:2011 温室气体.温室气体检验组和确认组的能力要求

Greenhouse gases. Competence requirements for greenhouse gas validation teams and verification teams

DB41/ 681-2011 啤酒工业水污染物排放标准

Discharge standard of water pollutants for beer industry

ISO 11057:2011 空气质量.可清洗过滤介质的过滤特性的试验方法

This International Standard specifies a standard reference test method for the comparative characterization of pulse-jet cleanable filter media, to be used in filter elements (e.g. bag filters, pocket filters, cartridge filters) applied in dry gas cleaning under standardized test conditions. The main purpose of testing is to gain information about both the operational performance and the particle emission of cleanable filter media. It should be noted that while one test apparatus and operating method has been chosen and described herein, it is recognized that other apparatus and operating arrangements can be found acceptable. In order for a candidate apparatus to become an equivalent apparatus, a comparison has to be performed with the standard reference apparatus according to a specified procedure (6.1). The test procedure, the characteristics of the required test facility, and the test conditions, as well as the evaluation and presentation of the results, are specified. The results obtained from this test method are not intended for prediction of the absolute performance of fullscale filter facilities. However, they are helpful for the selection and development of appropriate cleanable filter media and the identification of suitable operating parameters. Additional tasks such as verifying filter media concerning PM emissions, the classification of different media according to their filtration performance or the cleanability and durability of filter elements (i.e. projection of bag lifetime) can be addressed using the test method specified.

Air quality - Test method for filtration characterization of cleanable filter media

DB61/ 224-2011 黄河流域（陕西段）污水综合排放标准

本标准适用于陕西省辖区内以各种排放形式向黄河流域水体排放污水的单位的排放管理。

Integrated Wastewater Discharge Standards for the Yellow River Basin (Shaanxi Section)

ISO 25139:2011 固定源排放.气相色谱测定甲烷浓度方法手册

This International Standard specifies a manual method for the determination of the concentration of methane emissions from stationary sources. This International Standard specifies an independent method of measurement, which is validated for mass concentrations up to 1 500 mg/m. NOTE 1 An independent method of measurement is used for such purposes as calibration or validation of permanently installed measuring systems. NOTE 2 An “independent method of measurement” is termed “standard reference method (SRM)” in EN 14181[5].

Stationary source emissions - Manual method for the determination of the methane concentration using gas chromatography

DIN EN ISO 11771:2011 空气质量.时间平均质量排放与排放因素的测定.一般方法(ISO 11771-2010);德文版本EN ISO 11771-2010

This International Standard specifies a generic method for the determination and the reporting of time averaged mass emissions from a specific installation, or of a family of installations (or common source type), using data collected by measurement, and by establishing: - mass emission rates by the simultaneous measurement of concentration and gas flow, using standardized manual or continuous methods, and also the estimation of the uncertainty of the measurement; - time averaged mass emission rates using time series of mass emission rate values, their uncertainty characteristics, and also the determination of the expanded uncertainty of the average; - time averaged emissions factors for a specific installation or of a family of installations and their associated uncertainty characteristics; - a quality management system to assist the process of inventory quality assurance and verification. This International Standard is applicable to determining emissions factors or emissions reduction efficiency (both simultaneous and sequential) from stationary sources, including for emissions from industrial processes where calculation from fuel and raw material is not practical, greenhouse gases, and air pollutants including fine particulate material. This standard does not address compliance monitoring in the context of emission control regulations. This International Standard requires the use of measurement based methods and calculation-based methods that use measurement data. It covers the planning and execution of the measurement programme to collect data, selection of sampling methods, calculation of results, estimation of uncertainty, determination of emissions factors, and the reporting of information in a form that enables users to apply them. This standard specifies how to: - generate time averaged mass emissions rate data of a known quality, for a defined period of time, and a documented set of operational conditions; - generate complete data sets representative of a known time period (i.e. a calendar year) by filling gaps in mass emissions rate data series and combining data sets numerically; NOTE: Time series data may be available for only a limited elapsed period (i.e. weeks, months, or years) and may be available only for a discrete process whereas inventories may be necessary which average over a different period (i.e. for a calendar year). - calculate emissions factors for a known time period; - calculate time averaged emissions factors of a known quality for a known source type. The measurement of emissions from vehicular, area, or fugitive sources is not specifically covered. However, the standard can be used for quantification of emissions factors for those sources provided that measurements of emissions are available. This International Standard does not explicitly include measurement procedures that are fully described in the published standards in the normative references or in the bibliography. Neither does it provide advice on the generation of activity statistics. This International standard is compatible with ISO 14064-1 and ISO 14064-3.

Air quality - Determination of time-averaged mass emissions and emission factors - General approach (ISO 11771:2010); German version EN ISO 11771:2010

JIS Q 14064-2:2011 温室气体.第2部分:温室气体减少排放或排除增强功能的定量化,监控和报告用工程水平指导规范

Greenhouse gases -- Part 2: Specification with guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements

JIS Q 14064-3:2011 温室气体.第3部分:温室气体认定的批准和确认用指导规范

Greenhouse gases -- Part 3: Specification with guidance for the validation and verification of greenhouse gas assertions

JIS Q 14065:2011 温室气体.供温室气体确认和检验组织使用的鉴定合格或其他识别格式用要求

Greenhouse gases -- Requirements for greenhouse gas validation and verification bodies for use in accreditation or other forms of recognition

BS EN ISO 11771:2010 空气质量.按时间平均的质量排放量和排放因子的测定.一般方法

Air quality. Determination of time-averaged mass emissions and emission factors. General approach

ANSI/ACMA UEF-1-2011 估算敞开式模塑与其他流程的排放因子

This revison adds new emission factors for the compression molding of SMC (Shhet Molding Compound), BMC (Bulk Molding Compound), and LCM (Liquid Composite Molding).

Estimating Emission Factors from Open Molding and Other Processes

ASTM E2515-11 测定取样探管收集颗粒物排放量的标准试验方法

1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances including woodstoves, pellet-burning appliances, factory-built fireplaces, masonry fireplaces, masonry heaters, indoor furnaces, and indoor and outdoor hydronic heaters within a laboratory environment. 1.2 Analytes will be a particulate matter (PM) with no CAS number assigned. For data quality objectives, see Appendix X1. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution Tunnel

ANSI/LEO 5000-2011 LEO 5000.排放量清单,抵消量和减排信用标准

Develop a comprehensive framework and sustainability metrics that (1) Provide transparent reporting of the scope of emissions sources being addressed and how emissions, sequestration and offsets are calculated, which will help companies and consumers to make sense of claims made by businesses about their emission reduction and offset achievement, (2) Avoid the traditional one-dimensional approach of targeting single emissions by addressing the full range of emissions types, including those that negatively affect climate and those that negatively affect human health and (3) Fill in the gap left by current climate emissions standards by addressing existing forests.

LEO 5000 - Standard for Emissions Inventories, Offsets and Reduction Credits