Z60 污染物排放综合 标准查询与下载

ASTM E2515-10 测定取样探管收集的颗粒物排放量的标准试验方法

1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances including woodstoves, pellet-burning appliances, factory-built fireplaces, masonry fireplaces, masonry heaters, indoor furnaces, and indoor and outdoor hydronic heaters within a laboratory environment. 1.2 Analytes will be a particulate matter (PM) with no CAS number assigned. For data quality objectives, see Appendix X1. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Particulate Matter Emissions Collected by a Dilution tunnel

KS I ISO 10396:2009 固定源排放.固定安装的监测系统自动测定气体排放浓度的抽样

이 표준은 유출되는 기체 흐름의 기체 농도 자동측정을 위해 어떤 범위 내에서 대표적인 시료

Stationary source emissions-Sampling for the automated determination of gas emission concentrations forpermanently-installed monitoring systems

DIN EN ISO 23210:2009 固定污染源排放.烟气中钷10/钷2-5质量浓度的测定.低浓度下利用撞击计进行测量(ISO 23210：2009),德文版本EN ISO 23210:2009

This International Standard specifies a standard reference method for the determination of PM10 and PM2, 5 mass concentrations at stationary emission sources by use of two-stage inpactors. The measurement method is especially suitable for measurements of mass concentrations below 50 mg/m3 as half-hourly averages at standard conditions (273 K, 1013 hPa, dry gas). It is an acceptable method for the measurement in the flue gas of different installations such as cement and steel production as well as combustion processes. This International Standard is not applicable to sampling of flue gases that are saturated with water-vapour. This International Standard is not applicable where the majority of the particles are likely to exceed PM10 e. g. in case of raw gases or plant operating failures. This International Standard may not be used for the determination of the total mass concentration of dust.

Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009); German version EN ISO 23210:2009

NF X43-710:2009 固定污染源的排放.烟道气中PM10/PM2-5质量浓度的测定.第1部分:使用撞击取样器在低浓度下测量

Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Part 1 : measurement at low concentrations by use of impactors.

BS EN ISO 23210:2009 固定源排放.烟气中PM10/PM2.5质量浓度的测定.低浓度下利用撞击计进行测量

This International Standard specifies a standard reference method for the determination of PM10 and PM2,5 mass concentrations at stationary emission sources by use of two-stage impactors. The measurement method is especially suitable for measurements of mass concentrations below 40 mg/m3 as half-hourly averages in standard conditions (273 K, 1 013 hPa, dry gas). It is an acceptable method for the measurement in the flue gas of different installations, such as cement and steel production plants, as well as combustion processes. This International Standard is not applicable to the sampling of flue gases that are saturated with water vapour. This International Standard is not applicable where the majority of the particles are likely to exceed PM10, for example, in the case of raw gases or plant operating failures. NOTE 1 Measurements of particulate concentrations higher than 40 mg/m3, as a half-hourly average in standard conditions (273 K, 1 013 hPa, dry gas), can lead to overloading of the collecting plates and backup filters and also could result in shorter sampling times. NOTE 2 The collecting plates and backup filters can be used for further chemical analysis. This International Standard cannot be used for the determination of the total mass concentration of dust. NOTE 3 For data assessment purposes, it can be useful to perform measurements of total particulate matter in parallel to the PM10 and PM2,5 measurements. This International Standard describes the design, use and theory of round-nozzle impactors. It does not exclude other types of impactors, provided these systems meet the performance criteria specified in this International Standard in a validation of the impactor performed by an independent testing laboratory.

Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors

ISO 23210:2009 固定污染源排放.烟气中PM10/PM2.5质量浓度的测定.低浓度下利用撞击计进行测量

This International Standard specifies a standard reference method for the determination of PM10 and PM2,5 mass concentrations at stationary emission sources by use of two-stage impactors. The measurement method is especially suitable for measurements of mass concentrations below 40 mg/m3 as half-hourly averages in standard conditions (273 K, 1 013 hPa, dry gas). It is an acceptable method for the measurement in the flue gas of different installations, such as cement and steel production plants, as well as combustion processes. This International Standard is not applicable to the sampling of flue gases that are saturated with water vapour. This International Standard is not applicable where the majority of the particles are likely to exceed PM10, for example, in the case of raw gases or plant operating failures. NOTE 1 Measurements of particulate concentrations higher than 40 mg/m3, as a half-hourly average in standard conditions (273 K, 1 013 hPa, dry gas), can lead to overloading of the collecting plates and backup filters and also could result in shorter sampling times. NOTE 2 The collecting plates and backup filters can be used for further chemical analysis. This International Standard cannot be used for the determination of the total mass concentration of dust. NOTE 3 For data assessment purposes, it can be useful to perform measurements of total particulate matter in parallel to the PM10 and PM2,5 measurements. This International Standard describes the design, use and theory of round-nozzle impactors. It does not exclude other types of impactors, provided these systems meet the performance criteria specified in this International Standard in a validation of the impactor performed by an independent testing laboratory.

Stationary source emissions - Determination of PM₁₀/PM_2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors

BS 2742:2009 林格曼排烟浓度(Ringelmann)和小型烟雾表的使用

This British Standard provides guidance on the use of BS Ringelmann charts to assess smoke emissions from unregulated processes. It is not suitable for calibrating Continuous Emissions Monitoring Systems. It is not applicable to processes whose emissions are regulated by EU Directives with stated Uncertainty. NOTE Most regulated processes have particulate emissions limits below Ringelmann 1. This British Standard is intended for use with the related publications: • BS 2742C, Ringelmann chart; • BS 2742M, Miniature smoke chart. Other measuring devices or charts are not suitable for use with this British Standard.

Use of the Ringelmann and miniature smoke charts

DIN EN 1093-3 Berichtigung 1:2009 机械安全.气载有害物质的排放评估.第3部分:特定污染物排放率的测量用试验台方法.技术勘误DIN EN 1093-3-2008-09

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant; German version EN 1093-3:2006+A1:2008, Corrigendum to DIN EN 1093-3:2008-09

ASTM E2558-09 测定从低质木材燃烧火炉的炉火中排放的粒状物的标准试验方法

This test method is used for determining emission factors and emission rates for low mass wood-burning fireplaces. The emission factor is useful for determining emission performance during product development. The emission factor is useful for the air quality regulatory community for determining compliance with emission performance limits. The emission rate may be useful for the air quality regulatory community for determining impacts on air quality from fireplaces, but must be used with caution as use patterns must be factored into any prediction of atmospheric particulate matter impacts from fireplaces based on results from this method. The reporting units are grams of particulate per kilogram of dry fuel and grams of particulate per hour. Appropriate reporting units for comparing emissions from non-heating appliances: g/kg. Appropriate reporting units for predicting atmospheric emission impacts only if hours of fireplace use are factored in: g/h.1.1 This test method covers the fueling and operating protocol for determining particulate matter emissions from wood fires in low mass wood-burning fireplaces. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Particulate Matter Emissions from Fires in Low Mass Wood-Burning Fireplaces

DIN EN 1093-11:2008 机械安全性.气载有害物质排放量评定.第11部分:净化指数

This standard describes a method for the measurement of the decontamination index of pollution control systems e. g. capture devices including local exhaust ventilation, water spray systems and, when appropriate, separation equipment installed on a machine. This method uses the real pollutant (see 4.2 of EN 1093-1 : 1998 "Safety of machinery- Evaluation of the emission of airborne hazardous substances m Part 1: Selection of test methods'~ and can be operated in room or field environments. It should be observed that during the test, especially during the shutdown or the removal of the pollution control system, the concentration of hazardous substances, if present, can reach levels which are liable to incur a risk to the health of the operators or other occupants present in the room. Warning: This standard does not deal with the protective measures required to control these risks, ill Measurement of the decontamination index of pollution control system can serve for the: - evaluation of the performance of a pollution control system of a machine; - evaluation of the improvement of a pollution control system; comparison of pollution control systems for machines of similar design; ranking of pollution control systems according to their decontamination efficiency; determination of the air flow rate in the case of an exhaust system to achieve a given level; - determination of the state of the art of pollution control systems for machines with respect to the decontamina- tion efficiency.

Safety of machinery - Evaluation of the emission of airbone hazardous substances - Part 11: Decontamination index(includes Amendment A1:2008); English version of DIN EN 1093-11:2008-11

DIN EN 1093-9:2008 机械的安全性.气载有害物质排放的评估.第9部分:污染物浓度参数.室内法

This European Standard specifies a room method for the measurement of the pollutant concentration parameter of a specified airborne hazardous substance from machines, located in a test room and operating the machines under defined conditions. This method can only be used for machines with a local exhaust ventilation with an air flow rate 3 500 m3/h and machines without recirculated air. Measurement of the pollutant concentration parameter of a machine can serve for the: a) evaluation of the performance of a machine; b) evaluation of the improvement of the machine; c) comparison of machines within groups of machines with the same intended use (groups are defined by the function and materials processed); d) ranking of machines from the same group according to their pollutant concentration parameters; e) determination of the state of the art of machines with respect to their pollutant concentration parameter.

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method(includes Amendment A1:2008); English version of DIN EN 1093-9:2008-11

BIP 2117-2008 废弃物用电气和电子设备指令.要求和实施

The Waste Electrical and Electronic Equipment Directive - Requirements and implementation

DIN V 18232-8:2008 烟和热控制设备.第8部分:通风和排烟用建筑覆盖物的开口装置

Smoke and heat control systems - Part 8: Opening units for building coverings for ventilation and smoke elimination purposes

DIN EN 15445:2008 工业区共有的易排放和扩散的物质.通过反向扩散模型的易排放物质源的质量认证

This standard specifies a Reverse Dispersion Modelling method to qualify the fugitive emission rates of diffuse fine and coarse dust sources of industrial plants or areas. The application needs calculations using a dispersion model, and the definition of a sampling experimental set-up taking into account field data such as number, height and width of diffuse dust sources, sampling distances, and meteorological information. The RDM method does not allow quantification in absolute figures of the dust emission rates because of an undetermined accuracy depending on various site conditions, but it is a tool which enables each industrial plant to identify its dust sources that emit the most, and then to implement actions reducing their importance by self-control and related improvement process as part of environmental management. In this framework, the RDM method should not be used to control or verify any compliance with air quality threshold global values which might be contained in an operating permit, or to carry out comparison between different plants belonging to the same industrial sector.

Fugitive and diffuse emissions of common concern to industry sectors - Qualification of fugitive dust sources by Reverse Dispersion Modelling; English version of DIN EN 15445:2008-04

DIN EN 15446:2008 工业区共有的易排放和扩散的物质.设备和管道泄露产生的蒸汽中易排放物的测量

This standard applies to the measurement of fugitive emissions of volatile organic compounds (VOCs) from process equipment. The leak sources include, but are not limited to, valves, flanges and other connections, pressure relief devices, process drains, open-ended valves, pump and compressor seal systems, agitator seals, and access door seals. It does not apply to instrument tubing connections. This standard applies to all products of which at least 20 % by weight has a vapour pressure higher than 0,3 kPa at 20 ~C. For the petroleum industry, this includes all light products and excludes kerosene and all heavier products. The standard is based on the measurement of the gas concentration at the interface of a leak. This concentration is measured with a portable instrument. It is converted to a mass emission rate by use of a set of correlations. The scope of this standard includes the complete data processing, from the initial concentration measurement up to the generation of an emission report over a reporting period (which is generally one year)1). This standard does not prescribe the number of potential emission points that should be screened each year nor the frequency at which these points should be screened. This sampling strategy shall indeed take into account the plant characteristics and the required level of control over fugitive emissions. Optical methods are currently under development to ease the detection of leaks in plants and use of this standard in conjunction with these methods might be possible. In any case, measurements have to be performed according to the requirements of this standard. To enable direct quantification of total fugitive emissions based only on these methods, a subsequent revision of this standard will be needed.

Fugitive and diffuse emissions of common concern to industry sectors - Measurement of fugitive emission of vapours generating from equipment and piping leaks; English version of DIN EN 15446:2008-04

NF X43-446*NF EN 15446:2008 工业区共有的易排放和扩散物质.设备和管道泄露产生的蒸汽中易排放物的测量

Fugitive and diffuse emissions of common concern to industry sectors - Measurement of fugitive emission of vapours generating from equipment and piping leaks.

DIN CEN/TS 15674:2008 空气质量.固定源排放的测量.标准化法的校准用指南

Air quality - Measurement of stationary source emissions - Guidelines for the elaboration of standardised methods; German version CEN/TS 15674:2007

DIN CEN/TS 15675:2008 空气质量.固定源排放的测量.EN ISO/IEC 17025-2005定期测量的应用

Air quality - Measurement of stationary source emissions - Application of EN ISO/IEC 17025:2005 to periodic measurements; German version CEN/TS 15675:2007

ASTM D7459-08 从固体燃烧物排放中收集源生物和化石二氧化碳排放的标准实施规程

Greenhouse gases are reported to be a major contributor to global warming. Since “biomass CO2” emitted from combustion devices represents a net-zero carbon contribution to the atmosphere (that is, plants remove CO2 from the atmosphere and subsequent combustion returns it), it does not contribute additional CO2 to the atmosphere. The measurement of biomass (biogenic) CO2 allows regulators and stationary source owners/operators to determine the ratio of fossil-derived CO2 and biomass CO2 in developing control strategies and to meet federal, state, local and regional greenhouse gas reporting requirements. The distinction of the two types of CO2 has financial, control and regulatory implications.1.1 This practice defines specific procedures for the collection of gas samples from stationary emission sources for subsequent laboratory determination of the ratio of biomass (biogenic) carbon to total carbon (fossil derived carbon plus biomass or biogenic carbon) in accordance with D 6866. 1.2 This practice applies to stationary sources that burn municipal solid waste or a combination of fossil fuel (for example, coal, oil, natural gas) and biomass fuel (for example, wood, wood waste, paper, agricultural waste, biogas) in boilers, combustion turbines, incinerators, kilns, internal combustion engines and other combustion devices. 1.3 This practice applies to the collection of integrated samples over periods from 1 hour to 24 hours, or longer. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Collection of Integrated Samples for the Speciation of Biomass (Biogenic) and Fossil-Derived Carbon Dioxide Emitted from Stationary Emissions Sources

DB11/ 139-2007 锅炉大气污染物排放标准

本标准按新建、扩建、改建锅炉和在用锅炉两类，分别规定了锅炉的大气污染物排放限值。本标准适用于燃煤、燃油、燃气、生物质燃料锅炉和其他燃料锅炉大气污染物的排放控制，以及建设项目环境影响评价、设计、竣工验收和建成后的污染物排放控制。本标准不适用于以生活垃圾、危险废物为燃料的锅炉。

Emission standard of air pollutants for boilers