万分之一天平几位 标准查询与下载

JEDEC JESD16-A-1995 百万分之几平均输出质量水平的评估

Improvements in manufacturing .technology and methodology have resulted in corresponding quality improvements for electronic components. As a result

Assessment of Average Outgoing Quality Levels in Parts Per Million (PPM)

ANSI/EIA 554-1:1996 百万分之几（PPM）平均出厂质量指标的评估

Provides a uniform method if measurement and calculation of average outgoing quality levels. Minimum sample sizes and a method for aggregating data

Assessment of Average Outgoing Quality Levels in Parts Per Million (PPM)

ANSI/EIA 554-2:1996 百万分之几（PPM）不合格指标的估价

Provides a uniform method of assessing quality levels in situations with audit sampling rather than acceptance sampling is performed

Assessment of Nonconforming Levels in Parts Per Million (PPM)

ANSI/EIA 554-A:1996 百万分之几（PPM）输出不合格等级的估价

Provides guidance for selecting standardized methods for estimating the proportion nonconforming expressed a PPM

Assessment of Outgoing Nonconforming Levels in Parts Per Million (PPM)

ONORM A 6405-1998 百分比，每千次，百万分之一，点个百分点

Percent, per thousand, parts per million, point, percentage point

CNS 11082-1984 公斤力每平方公分与百万帕斯卡之换算表

本标准适用于工矿业通常使用之公斤力每平方公分（kgf∕cm）与百万帕斯卡（Mpa）之换算表（以下简称换算表

Kilogram-Force Per Square Centimeter-Mega Pascal Conversion Tables

SAE EIA-554_2-2016 以百万分率（PPM）为单位评估不合格水平

This standard is intended to provide a uniform method of determining proportion nonconforming in finished components and to provide a standardized

Assessment of Nonconforming Levels In Parts Per Million (PPM)

SAE EIA-554_1-2016 以百万分率（PPM）为单位的平均出厂质量水平评估

This standard is intended to provide a uniform method of calculating an estimate of the proportion nonconforming in finished components and to provide

Assessment of Average Outgoing Quality Levels in Parts Per Million (PPM)

JGJ 35-1987(第一部分) 建筑气象参数标准(第一部分)

Standard for parameter of construction atmosphere (Part 1)

43药典 第一增补本-2010 一部 新增品种 京万红软膏

来自第39页

A newly added variety Jingwanhong ointment

CNS 11086-1984 公斤力每平方公厘与百万帕斯卡之换算表

本标准适用于工矿业通常使用之公斤力每平方公厘（kgf∕mm2）与百万帕斯卡（Mpa）之换算表（以下简称换算表

Kilogram-Force Per Square Millimeter-Mega Pascal Conversion Tables

KS Q ISO 14560-2016 属性验收抽样程序——百万分之不合格项的规定质量水平

Acceptance sampling procedures by attributes－Specified quality levels in nonconforming items per million

SAE EIA-554A-2015 以百万分率（PPM）为单位评估不合格水平的方法选择

This standard is intended to provide guidance for selecting standardized methods for estimating the proportion nonconforming expressed as PPM

Method Selection for Assessment of Nonconforming Levels in Parts Per Million (PPM)

SAE EIA-554A-2002 以百万分率（PPM）为单位评估不合格水平的方法选择

Method Selection for Assessment of Nonconforming Levels in Parts Per Million (PPM)

CNS 3-13-1994 工程制图(几何公差–位置度公差之标注)

本标准描述位置度公差标注的原理，以为形态之定位。同时亦提供适于配合，公差值的计算公式。一般来说位置度公差标注可适用于规则和不规则的形态。为使此本标准易于暸解只用规则形态来表达

Engineering Drawing (Geometrical Tolerancing - Positional Tolerancing)