共找到 150 条与 熔融指数仪(熔体流动速率测定仪) 相关的标准,共 10 页
Verification Regulation of Extrusion Plastometer
本标准规定了熔体流动速率仪的要求、试验方法和标志、包装、运输、贮存和随行文件。 本标准适用于按GB/T 3682-2000规定的方法测定热塑性塑料熔体质量流动速率和熔体体积流动速率所使用的温度在120℃~450℃范围内的熔体流动速率仪(以下简称熔流仪
Specifications for the melt flow ratemeters
Melt flow rate instrument technical conditions
Melt Flow Rate Meter Technical Specifications
本标准规定了在规定的温度和负荷条件下测定热塑性塑料熔体流动速率和熔体体积流动速率的方法。通常测定熔体流动速率的试验条件由本标准引用的材料标准规定。热塑性塑料的一般试验条件列于附录A和附录B中。在比较填充和非填充热塑性塑料时,熔体体积流动速率是很有用的。如果知道实验温度下的熔体密度,则可以用
Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
本标准规定了两种测定热塑性弹性体熔体质量流动速率(MFR)和熔体体积流动速率(MVR)的方法,方法A是质量法,方法B是体积法。 本标准适用于烯烃类热塑性弹性体(POE)、苯乙烯类热塑性弹性体(TPE-S)、热塑性弹性体(TPU)、动态硫化型热塑性弹性体(TPV
Thermoplastic elastomer - Determination of the melt mass-flow rate and melt volume-flow rate
1.1 This International Standard specifies a method for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
Plastics – Determination of melt mass flow rate (MFR) and melt volume flow rate (MVR) of thermoplastics
D1238-Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1238-Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1238-Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
Instytut Chemii Przemys?owej, im. I. Mo?cickiego, Warszawa
Plastics. Determination of the melt massflow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
在规定的温度和负荷下,由通过规定长度和内孔直径的口模挤出的熔融物质测定熔体体积流动速率(MVR),通过计算转化为熔体质量流动速率(MFR)。 测定MVR,记录活塞在规定时间内的位移或活塞移动规定的距离所需的时间,计算挤出速率,以cm3/10 min表示。 用测量的MVR值乘以材料的熔体
Plastics—Ultrahigh melt fluidity polypropylene materials— Determination of melt volume-flow rate(MVR)and melt mass-flow rate(MFR)
This International Standard specifies two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
Denna standard beskriver en metod f?r best?mning av sm?ltindex f?r termoplaster under stipulerade betingel- < ser ifr?ga om temperatur och
Plastics - Determination of the melt flow rate of thermoplastics
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号