E46 炼厂气体 标准查询与下载

GB/T 30517-2014 液化石油气中游离水的试验 目视法

本标准规定了使用目视法测定液化石油气在0℃以下游离水存在的试验方法。本标准适用于液化石油气。

Test method for free water in liquefied petroleum gas.Visual inspection

GB/T 30518-2014 液化石油气中可溶性残留物的测定 高温气相色谱法

本标准规定了测定液化石油气(LPG)中可溶性残留物含量的试验方法,测定范围是40 mg/kg~100 mg/kg,如果残留物含量更高可通过调整试样量来控制。可溶性残留物的测定是将试样在环境温度下挥发,在105℃烘干后,用气相色谱进行检测。本标准不适于固体样品及高分子聚合物(>1 000 g/mol)的测定。

Determination of dissolved residues of liquefied petroleum gases.High temperature gas chromatographic method

GB 19159-2012 车用液化石油气

本标准规定了车用液化石油气的分类和标记、技术要求和试验方法、检验规则、标志、储存和运输、安全和健康等要求。 本标准适用于点燃式内燃机使用的车用液化石油气。

Automotive liquefied petroleum gases

GB 11174-2011 液化石油气

警告：如果不遵守适当的防范措施，本标准所属产品在生产、贮运和使用等过程中可能存在危险。本标准无意对与本产品有关的所有安全问题提出建议。用户在使用本标准之前，有责任建立适当的安全和防护措施，并确定相关规章限制的适用性。 本标准规定了液化石油气产品的分类和标记、要求和试验方法、检验规则、标志、包装、运输和贮存、交货验收和安全。 本标准适用于作工业和民用燃料的液化石油气。

Liquefied petroleum gases

GB 19159-2003 车用液化石油气

本标准规定了车用液化石油气的要求、试验方法、储存、标志、运输、安全及健康要求。本标准适用于车用液化石油气燃料。

Automotive liquefied petroleum gas

GB/T 13287-1991 液化石油气挥发性测定方法

本标准规定了测定液化石油气挥发性的方法。 本标准适用于丙烷型、丙-丁烷混合型和丁烷型液化石油气。 本标准指的挥发性是用试样被汽化95％（V/V）时的温度来表示，低挥发性的烃类化合物的存在意味着这个温度将会升高。本标准的试验结果可用来预测各种类型液化石油气中较高沸点组分的大致含量。 注意：液化石油气极易挥发、燃烧，操作时要注意有关安全问题。

Liquefied petroleum gases.Determination of volatility

GB/T 6602-1989 液化石油气蒸气压测定法(LPG法)

Liquefied petroleum gases--Determination of vapour pressure--LPG method

BS EN 15984:2017 石油工业和产品.精炼可燃气体合成物的测定以及碳含量和热值的计算.气相色谱法

Petroleum industry and products. Determination of composition of refinery heating gas and calculation of carbon content and calorific value. Gas chromatography method

NF M07-143:2017 石油工业及产品中精炼厂加热气体的成分测定(气相色谱法)以及含碳量和热值的计算

Petroleum industry and products - Determination of composition of refinery heating gas and calculation of carbon content and calorific value - Gas chromatography method

NF M41-003*NF EN 15471:2017 液化石油气.溶解的残留物的测定.高温重量分析法

Liquefied petroleum gases - Determination of dissolved residues - High tempareture gravimetric method

EN 1762:2017 气压为25bar(2.5MPa)及以下的液化石油气LPG(液相或气相)及天然气用橡胶软管和软管组件-规范

This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of 25 bar (2,5 MPa) and vacuum within the temperature range of -30 °C to +70 °C and, when designated -LT, -50 °C to +70 °C.

Rubber hoses and hose assemblies for liquefied petroleum gas@ LPG (liquid or gaseous phase)@ and natural gas up to 25 bar (2@5 MPa) - Specification

ASTM D1837-17 液化石油气(LP)挥发性的标准试验方法

4.1 Volatility, expressed in terms of the 958201;% evaporated temperature of the product, is a measure of the amount of least volatile components present in the product. Coupled with a vapor pressure limit, it serves to ensure essentially single-component products in the cases of commercial grades of propane and butane. When volatility is coupled with a vapor pressure limit which has been related to density, as in the case of the commercial PB-mixture, the combination serves to assure essentially two component mixtures for such fuels. When coupled with a proper vapor pressure limit, this measurement serves to assure that special-duty propane products will be composed chiefly of propane and propylene and that propane will be the major constituent. 1.1 This test method is a measure of the relative purity of the various types of liquefied petroleum (LP) gases and helps to ensure suitable volatility performance. The test results, when properly related to vapor pressure and density of the product, can be used to indicate the presence of butane and heavier components in propane-type LP-gas, and pentane and heavier components in propane-butane and butane-type fuels. The presence of hydrocarbon compounds less volatile than those of which the LP-gas is primarily composed is indicated by an increase in the 958201;% evaporated temperature. 1.2 When the type and concentration of higher boiling components is required, chromatographic analysis should be used. 1.3 The values stated in SI units are to be regarded as the standard. 1.3.1 Exception—The non-SI values are provided for information only. 1.4 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4.1 Note that thallium in a mercury-thallium thermometer is also a hazardous material. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Volatility of Liquefied Petroleum (LP) Gases

ISO 29945:2016 冷冻非石油基液化气体燃料. 二甲基乙醚(DME). 陆上终端的手动取样方法

This document specifies a manual sampling method for refrigerated liquefied DME at terminals in both loading and unloading ports along with precautions. This document does not include recommendations for the location of a sampling point in a line or vessel. This document is also applicable to the following cases, with necessary modifications: — sampling of DME on board liquefied gas tankers where appropriate sampling apparatus is provided; — sampling of other refrigerated, non-petroleum-based, liquefied gaseous fuels whose chemical and physical properties are similar to those of DME. The detailed chemical and physical properties of DME differ from those of LPG, which suggests that DME requires precautions different from those of LPG. However, their basic properties are similar to each other and so general reference is made in this document to precautions for LPG that have been applied in many countries. Reference can also be made to the appropriate individual items in this document for precautions concerning the quality.

Refrigerated non-petroleum based liquefied gaseous fuels - Dimethylether (DME) - Method of manual sampling onshore terminals

JIS K 2240 ERRATUM 1:2016 勘误

ERRATUM

EN 1440:2016 液化石油气设备及配件.传统可移动可再装的钎焊焊接液化石油气（LPG）钢瓶.检验周期

This European Standard specifies procedures for the periodic inspection and testing, of transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l. This European Standard is applicable to welded and brazed steel LPG cylinders with a specified minimum wall thickness designed according to EN 1442, EN 12807, EN 13322-1, or equivalent standard (e. g. national codes). This European Standard is intended to be applied to cylinders complying with RID/ADR (including pi marked cylinders) and also to existing non RID/ADR cylinder populations. NOTE The requirements of RID/ADR take precedence over those of this standard in the case of cylinders complying with that regulation, including pi marked cylinders. This European Standard does not apply to cylinders permanently installed in vehicles.

LPG equipment and accessories - Transportable refillable traditional welded and brazed steel Liquefied Petroleum Gas (LPG) cylinders - Periodic inspection (Incorporates Amendment A1: 2018)

GOST R 56851-2016 液化天然气. 热力学性质的计量方法

Liquefied natural gas. Method for calculation of thermodynamic properties

GOST R 57039-2016 液化石油气. 铜条腐蚀性的测定

Liquefied petroleum gases. Determination of corrosiveness to copper strip

GOST R 57040-2016 液化石油气. 残留的测定

Liquefied petroleum gases. Determination of residue

GOST R 56866-2016 气态烃和液化石油气. 采用紫外荧光法测定总挥发性硫

Gaseous hydrocarbons and liquefied petroleum gases. Determination of total volatile sulfur by method of ultraviolet fluorescence

GOST R 56868-2016 液化石油气. 挥发性的测定

Liquefied petroleum gases. Determination of volatility