N60 实验室仪器与真空仪器综合 标准查询与下载

GB/T 40343-2021 智能实验室 信息管理系统 功能要求

本文件规定了智能实验室信息管理系统的功能模型、核心功能要求、通信功能要求和系统管理功能要求,介绍了智能实验室信息管理系统的扩展功能。 本文件适用于不同领域智能实验室的信息管理系统,其他应用于实验室的信息系统可参照使用。 本文件也可作为实验室信息化改造、智能实验室建设的指导。

Intelligent laboratory—Information management system—Functional requirements

GB/T 39555-2020 智能实验室 仪器设备 气候、环境试验设备的数据接口

本标准规定了智能实验室用气候、环境试验设备与系统通信的数据接口的术语和定义.数据定义、数据类型和数据结构等。本标准适用于智能实验室领域具有数据接口功能的气候、环境试验设备。其他智能实验室仪吉设备可参照使用。

Intelligent laboratory—Instruments and equipment—Data interface of climatic and environmental testing equipment

GB/T 39556-2020 智能实验室 仪器设备 通信要求

本标准规定了智能实验室仪器设备与上层系统通信的总体要求、网络通信模型和命令格式等。 本标准适用于实验室中具有通信功能的仪器设备。

Intelligent laboratory—Instruments and equipment—Communication requirements

GB/T 35895-2018 微阵列生物芯片反应仪技术要求

Technical requirement of microarray hybridizer

GB/T 35891-2018 微阵列生物芯片清洗仪技术要求

Technical requirement of microarray washer

GB/T 34324-2017 微阵列生物芯片点样仪技术要求

Technical requirement of microarray biochip spotter

GB/T 33864-2017 质谱仪通用规范

General specification for mass spectrometer

GB/T 13979-2008 质谱检漏仪

本标准规定了质谱检漏仪（以下简称检漏仪）的要求、试验方法、检验规则、标志、包装、运输、贮存、质量保证等。 本标准适用于以质谱分析法作为检测手段的检漏仪。

Mass spectrometer leak detector

DB43/T 2452-2022 热灼减率分析仪通用技术要求

General technical requirements for heat loss rate analyzer

DB43/T 2453-2022 煤炭智能化验系统通用技术要求

General technical requirements for coal intelligent testing system

ISO 13528:2015 用实验室间对比进行技术检查的统计方法

This International Standard provides detailed descriptions of statistical methods for proficiency testing providers to use to design proficiency testing Schemes and to analyse the data obtained from those schemes. This Standard provides recommendations on the interpretation of proficiency testing data by participants in Such schemes and by accreditation bodies. The procedures in this Standard can be applied to demonstrate that the measurement results obtained by laboratories, inspection bodies, and individuals meet specified criteria for acceptable performance. This Standard is applicable to proficiency testing where the results reported are either quantitative measurements or dualitative Observations on test items. NOTE The procedures in this Standard may also be applicable to the assessment of expert opinion where the obpinions or judgments are reported in a form which may be compared objectively with an independent reference value or a consensus statistic, For exambple, when classifying proficiency test items into known categories by inspection - or in determining by inspection whether proficiency test items arise, or qo not arise, from the same original source - and the classification results are compared objectively the provisions of this Standqard that relate to nominal (qualitative) properties may apply.

Statistical methods for use in proficiency testing by interlaboratory comparison

GOST R ISO 15189-2015 医学实验室. 质量和能力的专业要求

Medical laboratories. Particular requirements for quality and competence

CFR 9-391.5-2013 动物与动物产品. 第391部分:检查服务和试验所认可费用. 第391.5节：实验所认可费用

(a) The annual fee for the initial accreditation and maintenance of accreditation provided pursuant to § 439.5 of this chapter shall be $5,000.00.

Animals and Animal Products. Part391:Fees and charges for inspection services and laboratory accreditation. Section391.5:Laboratory accreditation fees.

EN 16205:2013 行走在地板上的噪声的实验室测量

This European Standard specifies a laboratory measurement method to determine noise radiated from a floor covering on a standard concrete floor when excited by a standard tapping machine.

Laboratory measurement of walking noise on floors

PD CEN/TR 16589:2013 实验室装置.带铰接提取臂的捕捉装置

This Technical Report gives guidance regarding the selection, specification, installation and use of capture devices with articulated extract arm (abbreviated: AEAs) in laboratories. The informative material provided includes the general concept of AEAs, the variety of sub-types available, system installation issues, performance metrics and operational factors such as use, maintenance and training.

Laboratory installations - Capture devices with articulated extract arm

ASTM E2312-11 清结室材料测试的标准操作规程

This practice is not intended to advocate or discourage use of any particular test method. It is intended for information only, and to provide a useful guide for further detailed study, test, and evaluation of cleanroom materials and products.1.1 This practice identifies test methods used to evaluate the properties of various materials and products used in cleanrooms and for cleanroom construction. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Tests of Cleanroom Materials

EN ISO/TS 22367:2010 医学实验室.通过风险管理和持续改进减少误差

Medical laboratories - Reduction of error through risk management and continual improvement

ASTM E1502-10 供基准温度冰点室使用的标准指南

A pure material has a well-defined phase transition behavior, and the phase transition plateau, a characteristic of the material, can serve as a reproducible reference temperature for the calibration of thermometers. The melting or freezing points of some highly purified metals have been designated as defining fixed points on ITS-90. The fixed points of other materials have been determined carefully enough that they can serve as secondary reference points (see Table 1 and Table 2). This guide presents information on the phase transition process as it relates to establishing a reference temperature. Fixed-point cells provide users with a means of realizing melting and freezing points. If the cells are appropriately designed and constructed, if they contain material of adequate purity, and if they are properly used, they can establish reference temperatures with uncertainties of a few millikelvins or less. This guide describes some of the design and use considerations. Fixed-point cells can be constructed and operated less stringently than required for millikelvin uncertainty, yet still provide reliable, durable, easy-to-use fixed points for a variety of industrial calibration and heat treatment purposes. For example, any freezing-point cell can be operated, often advantageously, as a melting-point cell. Such use may result in reduced accuracy, but under special conditions, the accuracy may be commensurate with that of freezing points (see 6.3.10). The test procedure described in this guide produces qualification test data as an essential part of the procedure. These data furnish the basis for quality control of the fixed-point procedure. They provide for evaluation of results, assure continuing reliability of the method, and yield insight into the cause of test result discrepancies. The test procedure is applicable to the most demanding uses of fixed-point cells for precise thermometer calibration; it may not be appropriate or cost-effective for all applications. It is expected that the user of this guide will adapt the procedure to specific needs.1.1 This guide describes the essential features of fixed-point cells and auxiliary apparatus, and the techniques required to realize fixed points in the temperature range from 29 to 1085°C. 1.2 Design and construction requirements of fixed-point cells are not addressed in this guide. Typical examples are given in Fig. 1 and Fig. 2. 1.3 This guide is intended to describe good practice and establish uniform procedures for the realization of fixed points. 1.4 This guide emphasizes principles. The emphasis on principles is intended to aid the user in evaluating cells, in improving technique for using cells, and in establishing procedures for specific applications. 1.5 For the purposes of this guide, the use of fixed-point cells for the accurate calibration of thermometers is restricted to immersion-type thermometers that, when inserted into the reentrant well of the cell, (1) indicate the temperature only of the isothermal region of the well, and (2) do not significantly alter the temperature of the isothermal region of the well by heat transfer. 1.6 This guide does not address all of the details of thermometer calibration. 1.7 This guide is intended to complement special operating instructions supplied by manufacturers of fixed-point apparatus. 1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 The following hazard caveat pertains only to the test method portion, Section 7, of this guide. This standard does not purport to address all of the safet......

Standard Guide for Use of Freezing-Point Cells for Reference Temperatures

KS Q ISO 13528:2009 实验室间对比进行技术检查的统计方法

시험소 간 비교에 의한 숙련도 시험은 특정 시험이나 측정에 대한 각 시험소의 수행 능력을

Statistical methods for use in proficiency testing by interlaboratory comparisons

JJF 1223-2009 驻波管校准规范

本规范适用于用驻波比法测量表面声阻抗率和吸声系数声阻抗管的校准。

Calibration Spectification for Standing Wave Tubes