Q41 硅质耐火材料 标准查询与下载

GB/T 2608-2012 硅砖

本标准规定了硅砖的分类、技术要求、试验方法、质量评定程序、包装、标志、运输、储存及质量证明书。 本标准适用于硅质耐火砖。

Silica refractory bricks

GB/T 6900-2006 铝硅系耐火材料化学分析方法

本标准规定了铝硅系耐火材料的化学分析方法。 本标准分析的项目如下： a） 灼烧减量（LOI)； b）二氧化硅（Si0)； c）氧化铝（Al0）； d）氧化铁（Fe0）； e）二氧化钛（Ti0）； f）氧化钙（CaO）； g）氧化镁（MgO）； h）氧化钾（K0）； i）氧化纳（Na0）； J）氧化锰（MnO）； k）五氧化二磷 (P0)。 本标准适用的分析元素含量范围（质量分数）见表1。

Chemical analysis of alumina-silica refractories

GB/T 2608-2001 硅砖

本标准规定了硅砖的分类、技术要求、试验方法、检验规则、包装、标志、运输、储存及质量证明书。 本标准适用于单重

Silica refractory bricks

GB/T 17106-1997 耐火材料导热系数试验方法(平行热线法)

本标准规定了平行热线法测定耐火材料的导热系数。 本标准适用于测量温度不大于1250℃、导热系数小于25W/（m·K）的材料，不适用于导电材料。在1.2规定的范围内，本法还适用于粉状料及颗粒料（见7.2）。注 1）不烧砖和不定形耐火材料预制件的导热系数由于受硬化或凝固后残留水在加热时脱水的影响，试样须作预处理。预处理的方法、程度和试样在测量温度时的保温时间等细节超出了本标准的范围，应由有关双方协商一致。 2）测量非均质材料一般是困难的，尤其是含有纤维的材料，使用本方法对这类材料的测量也应由有关双方协商一致。

Refractory materials--Determination of thermal conductivity--Hot-wire method (parallel)

GB/T 16555.4-1996 碳化硅耐火材料化学分析方法 EDTA容量法测定三氧化二铝量

本标准规定了EDTA容量法测定三氧化二铝量的方法提要、试剂、试样、分析步骤、分析结果的表述及允许差。 本标准适用于不含锆、锰、铬等重金属的碳化硅耐火材料中三氧化二铝量的测定。测定范围：三氧化二铝1.00％～60.00％。 本标准遵守GB1467《冶金产品化学分析方法标准的总则及一般规定》。

Chemical analysis for silicon carbide refractories--Determination of alumina--EDTA gas volumetric method

GB/T 16555.2-1996 碳化硅耐火材料化学分析方法 气体容量法测定碳化硅量

本标准规定了气体容量法测定游离碳量、总碳量和碳化硅量的方法提要和原理、试剂和材料、仪器设备、试样、分析步骤、分析结果的表述及允许差。 本标准适用于不含石墨的碳化硅耐火材料中游离碳量、总碳量和碳化硅量的测定。 测定范围：游离碳0.10%～5.00%，总碳3.00%～15.00%，碳化硅5.00%~45.00%。

Chemical analysis for silicon carbide refractories--Determination of silicon carbide--Gas volumetric method

GB/T 16555.1-1996 碳化硅耐火材料化学分析方法 吸收重量法测定碳化硅量

本标准规定了吸收重量法测定游离碳量、总碳量和碳化硅量的方法提要、试剂和材料、仪器设备、试样、分析步骤、分析结果的表述及允许差。 本标准适用于碳化硅耐火材料中游离碳量、总碳量和碳化硅量的测定。 测定范围：游离碳0.10%～5.00%，总碳≥15.00％，碳化硅≥45.00%。

Chemical analysis for silicon carbide refractories--Determination of silicon carbide--Absorb gravimetric method

GB/T 16555.6-1996 碳化硅耐火材料化学分析方法 测定二氧化硅量

本标准规定了测定二氧化硅量的方法提要、试剂和材料、仪器设备、试样、分析步骤、分析结果的表述及允许差。 本标准适用于SiC≤15%的碳化硅耐火材料中二氧化硅量的测定。 测定范围：二氧化硅≥20.00%。

Chemical analysis for silicon carbide refractories--Determination of silicon dioxide

GB/T 16555.5-1996 碳化硅耐火材料化学分析方法 邻二氮杂菲光度法测定三氧化二铁量

本标准规定了邻二氮杂菲光度法测定三氧化二铁的方法提要、试剂、仪器、分析步骤、分析结果的表述及允许差。 本标准适用于碳化硅耐火材料中三氧化二铁量的测定。 测定范围：三氧化二铁0.05%～4.00%。 本标准遵守GB 1467-78《冶金产品化学分析方法的总则及一般规定》。

Chemical analysis for silicon carbide refractories--Determination of ferric oxide--o-Phenanthroline photometric method

GB/T 16555.3-1996 碳化硅耐火材料化学分析方法 气体容量法测定游离硅量

本标准规定了气体容量法测定游离硅量的方法提要和原理、试剂和材料、仪器设备、试样、分析步骤、分析结果的表述及允许差。 本标准适用于碳化硅耐火材料中游离硅量的测定。测定范围：游离硅0.10％～3.00％。

Chemical analysis for silicon carbide refractories--determination of free silicon--Gas volumetric method

GB/T 2608-2012(英文版) 硅质耐火砖

Silica refractory bricks

YB/T 4857-2020 半硅质隔热耐火砖

Semi-siliceous insulating refractory bricks

YB/T 4578-2016 熔融石英砖

Fused quartz brick

YB/T 4548-2016 蜡石砖

本标准规定了蜡石砖的术语和定义、牌号、形状尺寸、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。 本标准适用于无精炼钢包和铁水包工作层，各种钢包、铁水包、混铁车等设备永久层及其他热工设备炉衬用蜡石砖。

Pyrophyllite bricks

KS L 3111-2012 耐火砖尺寸试验方法

이 표준은 모양이 KS L 3101에 규정된 표준형 내화 벽돌 및 이에 준하는 육면체의 내

Testing methods for dimensions of refractory bricks

DIN EN ISO 21068-3:2008 含碳化硅的原材料和耐火制品的化学分析.第3部分:氮、氧和金属及氧化成分的测定

This part of ISO 21068 specifies methods for the determination of total nitrogen and nitrogen calculated as silicon nitride, total oxygen, and free metallic and oxidic components in silicon carbide raw materials and refractory products. It applies only to silicon carbide materials that are not bonded with nitrogen. Nitride-bonded silicon carbide refractories are covered in EN 12698-1.

Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituents (ISO 21068-3:2008); English version of DIN EN ISO 21068-3:2008-12

DIN EN ISO 21068-2:2008 含碳化硅的原材料和耐火制品的化学分析.第2部分:点火、总碳、单体碳和碳化硅、总二氧化硅和游离二氧化硅及总硅和游离硅减少的测定(ISO 21068-2-2008).英文版本DIN EN ISO 21068-2-2008

This part of ISO 21068 specifies analytical techniques for the determination of change in mass by thermal treatment at specified temperatures, and methods for the determination of the total carbon content, free carbon, silicon carbide, silicon, total silica and free silica content of silicon-carbide-containing raw materials and refractory products.

Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 2: Determination of loss on ignition, total carbon, free carbon and silicon carbide, total and free silica and total and free silicon (ISO 21068-2:2008); English

DIN EN ISO 21068-1:2008 含碳化硅的原材料和耐火制品的化学分析.第1部分:一般信息和样品制备

This part of ISO 21068 gives definitions and specifies techniques for the preparation of samples for the chemical analysis of silicon-carbide-containing raw materials and refractory products including: a) graphite brick containing silicon carbide; b) silicon carbide brick (includes the bricks containing silicon nitride); c) refractories containing carbon and/or silicon carbide mixed with clay; d) refractories containing carbon and/or silicon carbide mixed with silica (and fused silica); e) refractories containing carbon and/or silicon carbide mixed with high alumina material; f) refractories containing carbon and/or silicon carbide mixed with magnesia (and dolomite); g) refractories containing carbon and/or silicon carbide mixed with chrome mineral or magnesia-chrome materials; h) refractories containing carbon and/or silicon carbide except those described in a) to g) above. The items of chemical analysis described in ISO 21068, Parts 1 to 3 are as follows: 1) loss on drying (LOD); 2) loss on ignition (LOI); 3) total carbon, Ctotal; 4) free carbon, Cfree; 5) silicon carbide, SiC; 6) free silicon (Sifree); 7) free aluminium (Alfree); 8) free magnesium (Mgfree); 9) free iron (Fefree); 10) silicon(IV) oxide (SiO2); 11) aluminium oxide (AI203); 12) iron(Ill) oxide (total iron oxide calculated as Fe203); 13) titanium(IV) oxide (TiO2); 14) calcium oxide (CaO); 15) magnesium oxide (MgO); 16) sodium oxide (Na20); 17) potassium oxide (K20); 18) chromium(Ill) oxide (Cr203); 19) zirconium oxide (ZrO2); 20) boron oxide (total boron calculated as B203); 21) nitrogen; 22) oxygen; 23) nitrides (undifferentiated: Si3N4, AIN, BN, sialon, oxy-nitrides, etc.).

Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 1: General information and sample preparation (ISO 21068-1:2008); English version of DIN EN ISO 21068-1:2008-12

BS EN ISO 21068-2:2008 含碳化硅的原材料和耐火制品的化学分析.点火、总碳、单体碳和碳化硅、总二氧化硅和游离二氧化硅及总硅和游离硅减少的测定

This part of ISO 21068 specifies analytical techniques for the determination of change in mass by thermal treatment at specified temperatures, and methods for the determination of the total carbon content, free carbon, silicon carbide, silicon, total silica and free silica content of silicon-carbide-containing raw materials and refractory products.

Chemical analysis of silicon-carbide-containing raw materials and refractory products -Part 2: Determination of loss on ignition, total carbon, free carbon and silicon carbide, total and free silica and total and free silicon

BS EN ISO 21068-1:2008 含碳化硅的原材料和耐火制品的化学分析.一般信息和样品制备

This part of ISO 21068 gives definitions and specifies techniques for the preparation of samples for the chemical analysis of silicon-carbide-containing raw materials and refractory products including: a) graphite brick containing silicon carbide; b) silicon carbide brick (includes the bricks containing silicon nitride); c) refractories containing carbon and/or silicon carbide mixed with clay; d) refractories containing carbon and/or silicon carbide mixed with silica (and fused silica); e) refractories containing carbon and/or silicon carbide mixed with high alumina material; f) refractories containing carbon and/or silicon carbide mixed with magnesia (and dolomite); g) refractories containing carbon and/or silicon carbide mixed with chrome mineral or magnesia-chrome materials; h) refractories containing carbon and/or silicon carbide except those described in a) to g) above. The items of chemical analysis described in ISO 21068, Parts 1 to 3 are as follows: 1) loss on drying (LOD); 2) loss on ignition (LOI); 3) total carbon, Ctotal; 4) free carbon, Cfree; 5) silicon carbide, SiC; 6) free silicon (Sifree); 7) free aluminium (Alfree); 8) free magnesium (Mgfree); 9) free iron (Fefree); 10) silicon(IV) oxide (SiO2); 11) aluminium oxide (Al2O3); 12) iron(III) oxide (total iron oxide calculated as Fe2O3); 13) titanium(IV) oxide (TiO2); 14) calcium oxide (CaO); 15) magnesium oxide (MgO); 16) sodium oxide (Na2O); 17) potassium oxide (K2O); 18) chromium(III) oxide (Cr2O3); 19) zirconium oxide (ZrO2); 20) boron oxide (total boron calculated as B2O3); 21) nitrogen; 22) oxygen; 23) nitrides (undifferentiated: Si3N4, AlN, BN, sialon, oxy-nitrides, etc.).

Chemical analysis of silicon-carbide-containing raw materials and refractory products -Part 1: General information and sample preparation