共找到 596 条与 进排气与燃油供给系统 相关的标准,共 40 页
Diesel engines—Fuel filters—Method for evaluating fuel/water separation efficiency
Fuel filter—Initial single-pass efficiency test method
Filling receptacle of CNG vehicle
Filling receptacle of LPG vehicle
GB/T 28957的本部分规定了用于滤清器评定的五种无机试验粉尘的颗粒尺寸分布、这些粉尘一般用于以重量法评定内燃机燃油滤清器和机油滤清器各种不同试验方法的试验、试验粉尘也可以用于其他方面,例如需要不同的已知坚硬磨料的颗粒尺寸分布情况下的磨损试验、
Road vehicles.Test dust for filter evaluation.Part 2:Aluminium oxide test dust
本标准规定了柴油机旋装式燃油滤清器滤座的安装和连接尺寸、本标准适用于装有GB/T 28953-2012规定的外径不大于88 mm的旋装式燃油滤清器、
Automotive diesel.Heads for fuel filters with horizontal flange.Mounting and connecting dimensions
本标准规定了柴油机具有垂直安装面的燃油滤清器滤座的安装和连接尺寸、本标准适用于螺栓固定的滤清器和装有GB/T 28953-2012规定的外径不大于88 mm的旋装式燃油滤清器滤座、
Automotive diesel.Heads for fuel filters with vertical flange.Mounting and connecting dimensions
本标准规定了商用车辆常用空气滤清器滤芯尺寸。 也适用于其他滤清器滤芯。 2 尺寸规范
Commercial Vehicles.Dimenions of air filter elements.Part 1:Types A and B
本标准规定了汽车柴油机用双级燃油滤清器的安装和连接尺寸a 本标准适用于汽车柴油机用双级燃油滤清器。 2 尺寸和公差
Automotive diesel.Two-stage fuel filters for compression-ignition engines.Mounting and connecting dimensions
Mounting and connection dimensions of fuel filter holders for automotive diesel engines with vertical mounting surfaces
本标准规定了商用车辆用空气滤清器滤芯尺寸。 本标准适用于商用车辆用空气滤清器滤芯,也适用于其他滤清器滤芯。 2 尺寸规范
Commercial Vehicles.Dimenions of air filter elements.Part 2:Types C and D
本标准规定了内燃机和空气压缩机用进气空气滤清器试验室性能试验的试验程序.试验条件、试验设备及试验结果整理,从而使同类型空气滤清器的试验室性能试验结果之间具有可比性。 本标准适用于汽车及工业用途的内燃机和空气压缩机上用的进气空气滤清器。
Inlet air cleaning equipment for internal combustion engines and compressors.Performance testing
本标准规定了汽车柴油机用旋装式燃油滤清器互换性的基本尺寸和标记方法。 本标准适用于汽车柴油机用旋装式燃油滤清器。 旋裝式燃油濾清器的優選結構是不帶內部密封圈的,它們在第2 章中作出規定。 如果需要內部密封圈,可選用附錄A的濾清器結構。 相应滤清器接头参见ISO7310 ISO7311(见参考文献)。 2 尺寸和公差
Automotive diesel.Spin-on fuel filters for diesel engines.Mounting and connecting dimensions
本标准规定了汽车柴油机燃油滤清器〈简称滤清器)的性能试验方法y从而使滤清器的试验室性能试验结果具有可比性”本标准适用于额定体积流量(或标称体积流量)在200 L/h 以下的汽丰柴油机燃油濾清器‥对额定体积流量大于200 L/h 的滤清器可参照使用。
Test methods of fuel filter for automotive compression ignition engines
本标准规定了轻型汽油车用岐管式催化转化器的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于轻型汽油车用岐管式催化转化器,也适用于燃用液化石油气(LPC)车辆的岐管式催化转化器。
Manifold catalytic converter
本标准规定了全地形车燃油箱的安全性能要求和试验方法。 本标准适用于全地形车用的各种金属燃油箱和非金属燃油箱。
Safety property requirements and test method for fuel tanks of all-terrain vehicles
本标准规定了全地形车燃油箱的安全性能要求和试验方法。 本标准适用于全地形车用的各种金属燃油箱和非金属燃油箱。
Safety property requirements and test method for fuel tanks of all-terrain vehicles
本标准规定了带有液化石油气(LPG)装置的机动车辆用最大内径为20mm的橡胶软管和软管组合件的要求,这些软管的最大工作压力为2.5Mpa,工作温度为-40℃~+80℃。
Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles
本部分规定了液化石油气汽车加气口(快插件)的定义、型式、要求、试验方法、检验规则、标志、包装、出厂文件、运输及贮存。 本部分适用于使用符合GB 19159要求的汽车用液化石油气为工作介质,公称工作压力为2.2MPa(本标准所述压力值均为表压),工作环境温度为-40℃~60℃的液化石油气汽车加气口。
Filling receptacle of LPG vehicle-Part 2:Insert
本标准规定了在用汽车改装为汽油/压缩天然气两用燃料汽车的改装技术要求。 本标准适用于天然气额定工作压力不大于20MPa的汽油/压缩天然气两用燃料汽车的改装。
The technical criterion of refitting for vehicle by using gas--Compressed natural gas for vehicle(CNGV)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号