T25 底盘其它设备 标准查询与下载

DB44/T 1819-2016 汽车垂直升降尾板

本标准规定了汽车垂直升降尾板的术语和定义、型号、基本参数、要求、试验方法、检验规则、标志和使用说明书、包装、运输及贮存。 本标准适用于安装在车辆尾部起装卸货物作用的液压式垂直升降尾板（以下简称尾板）。

Car Vertical Lift Tail Lift

ISO 11407:2004 商用道路车辆.尾部带向前和向下连接器的牵引车和中轴挂车间的机械连接.互换性

This International Standard specifies the interchangeability requirements of the various elements and dimensions for the mechanical coupling of towing vehicles whose coupling is mounted forward and below to centre-axle trailers. It is applicable to road trains for the commercial transport of low-density, high-volume cargo of the greatest possible variety. It is also applicable to corresponding equipment in cases where the same vehicle makes up part of a road train having more than one trailer. It is not applicable to dedicated or special combinations such as coupling systems with an extensible drawbar; nor does it specify limitations on maximum gross mass and overall dimensions, which are generally laid down by legislative requirements. Vehicle combinations whose couplings form the subject of this International Standard (see Annex B for examples) are not interchangeable with those whose couplings are rear-mounted (see ISO 11406).

Commercial road vehicles - Mechanical coupling between towing vehicles, with coupling mounted forward and below, and centre-axle trailers - Interchangeability

ISO 13216-2:2004 道路车辆.儿童约束系统在车内的固定点及主固定点的安装.第2部分:顶部系留的固定点及其连接

This part of ISO 13216 establishes the positioning zones, dimensions and general and static-strength requirements for top tether anchorages used together with seat bight anchorages according to ISO 13216-1 or with other systems for anchoring child restraint systems (CRS) in road vehicles. It is applicable to child restraint systems intended for children with a mass of up to 22 kg. NOTE Further specifications for top teiher anchorages, straps and connectors could exist in other standards and regulations.

Road vehicles - Anchorages in vehicles and attachments to anchorages for child restraint systems - Part 2: Top tether anchorages and attachments

GM 9985182-2004 准SAE.80W-90石油车轴润滑剂,

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Oil - Axle Lubricant, Hypoid, SAE 80W-90

QC/T 696-2002 汽车底盘集中润滑系统技术要求

本标准规定了汽车底盘集中润滑系统的分类、技术要求、安装、标志、包装、运输和贮存。 　　本标准适用于润滑点不少于6个各类汽车底盘所安装的集中润滑系统。

Technical requirements for centralized lubrication system of automobile chassis

GM 9985164-2000 1-2号高温水喷雾耐润滑脂

Despite spot check8 poaalbiy periromed by opel, It Is the supplier's responslbllity that the delhrered parts are in line with the Opel drawings. DeliWrle3 Of ~mPle8,firstOff-tOOpla Itsand partqwhose performance has been changed, must be accompanied by a

Grease, High Temperature Water Spray Resistant, No. 1-2 Revision C

ISO/TR 12349-2:1999 道路车辆 约束系统试验用假人 第2部分:儿童假人

This Technical Report describes the infant and child crash test dummies which are recommended by ISO for use in evaluating child restraints and their interactions with deploying air bags.

Road vehicles - Dummies for restraint system testing - Part 2: Child dummies

ISO 13216-1:1999 道路车辆 儿童约束系统在车内的固定点及主固定点的安装 第1部分:座椅座面与靠背之间的固定点及其连接

This part of ISO 13216 specifies the dimensions, general requirements and static strength requirements of rigid anchorages for anchoring child restraint systems (CRS) in vehicles. It is applicable to fittings for the installation of CRSs for children with a mass of up to 22 kg, by means of two rigid anchorages positioned in the seat bight area, in passenger carrying vehicles. NOTE 1 This mass limit applies to CRSs where the inertia forces of the child and CRS are transferred via the anchorage system for the CRS. The anchorages may be used for systems for larger children, such as seats where the main forces are transferred through the adult seat belt, provided that the forces applied to the anchorages and the resulting excursions (see 4.2) do not exceed the limits in this part of ISO 13216. To assure compatibility with the anchorages, this part of ISO 13216 also specifies important features of CRSs equipped with rigid attachments, such as critical dimensions of the attachments and general requirements for handling. Supplementary devices, such as tether straps and reaction bars, which may be necessary for specific vehicle configurations or to fulfil performance criteria included in national and international standards and regulations, are not specified in this part of ISO 13216. An interim anchorage system that employs semi-rigid anchorages in the vehicle is described in annex A. Requirements for optional non-rigid attachments on the CRS are given in annex B. NOTE 2 Performance and strength requirements for the homologation of CRSs using attachments according to this part of ISO 13216 are presumed to be specified in other standards and regulations.

Road vehicles - Anchorages in vehicles and attachments to anchorages for child restraint systems - Part 1: Seat bight anchorages and attachments

ISO/TR 12349-1:1999 道路车辆 约束系统试验用假人 第1部分:成年假人

This Technical Report describes the adult crash test dummies which are recommended by ISO for use in evaluating the occupant protection potential of restraint systems in frontal and side impact test procedures.

Road vehicles - Dummies for restraint system testing - Part 1: Adult dummies

TB/T 1801-1999 货车用车钩尾框托板

本标准规定了货车用车钩尾框托板的型式与尺寸、技术要求及标记等。 本标准适用于装用各型缓冲器的铁道货车。

Truck coupler tail frame support plate

QC/T 584-1999 汽车底盘产品质量检验评定方法

本标准规定了二、三类汽车底盘产品质量检验的抽样规定、检验内容、检验方法和评定方法。 　　本标准适用于M类、N类汽车的二、三类汽车底盘产品质量监督检验。

Quality inspection and evaluation method of automobile chassis products

GM 9985010-1994 液压助力转向流体

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 165000 zu prüfen.

Fluid, Hydraulic Power Steering Revision M

SAE J510-1992 根据例定美国单位制造的汽车悬吊用板簧

This SAE Standard is limited to concise specifications promoting an adequate understanding between spring maker and spring user on all practical requirements in the finished spring. The basic concepts for the spring design and for many of the details have been fully addressed in HS-J788, SAE Information Report, Manual on Design and application of leaf Springs, which is available from SAE Headquarters.

Leaf Springs for Motor Vehicle Suspension Made to Customary U.S. Units

GM 9985299-1990 299级厌氧护化合物

Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Retaining Compound, Anaerobic, Grade 299 Revision C

GM 9985020-1989 油脂基地(排气联合)封闭剂

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 110000 zu prüfen.

SEALER, GREASE BASE (EXHAUST JOINT)

GM 9985013-1989 液压制动器流体

Only the latest approved standards are applicable unless otherwise specified.

Fluid, Hydraulic Brake

GM 9985012-1989 乙醇型(防冻结)冷却液集中-汽车发动机

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 165000 zu prüfen.

Coolant Concentrate - Automotive Engine, Glycol Type (Anti-Freeze)

GM 9985058-1989 乙醇型聚丙烯润滑油

Only the latest approved standards are applicable unless otherwise specified.

Lubricant, Polypropylene Glycol Type

GM 9985054-1989 16层棉缠绕

In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen Mindestanforderungen sind grundsatzlich nach TM 110000 zu prüfen.

TWINE, 16 PLY COTTON

GM 9985084-1989 氧化锌及钙型油脂

Only the latest approved standards are applicable unless otherwise specified.

Grease, Zinc Oxide and Calcium Type