A29;H61 标准查询与下载

DIN 17611:2000 精制铝和精制铝合金的阳极氧化产品.交货技术条件

The document specifies the technical conditions of delivery for anodized products of wrought aluminium and wrought aluminium alloys, used preferably in metall finishing. It does not apply to products with oxidation coatings produced by hard anodic axidation (process) for technical purposes, products with oxidation coatings produced by coil anodic axidation (process) and products worked after anodic oxidation.

Anodized products of wrought aluminium and wrought aluminium alloys - Technical conditions of delivery

DIN EN 12373-3:1999 铝和铝合金.阳极处理.第3部分:阳极的氧化涂层厚度的测定.用裂隙梁显微镜进行无损测量

The measurements apply in the most common cases to anodic oxide coatings having a thickness more than 10?or from 5?with an even surface. The use of the measurement is limited by two factors: an opaque coating and an uneven surface.

Aluminium and aluminium alloys - Anodizing - Part 3: Determination of thickness of anodic oxidation coatings; non-destructive measurement by split-beam-microscope; German version EN 12373-3:1998

DIN EN 12373-2:1999 铝和铝合金.阳极处理.第2部分:阳极处理氧化涂层单位面积质量(与面积相关的质量)的测定.重力法

Aluminium and aluminium alloys - Anodizing - Part 2: Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method; German version EN 12373-2:1998

DIN EN 12373-6:1999 铝和铝合金.阳极处理.第6部分:在预先未进行酸处理情况下涂层在铬酸/磷酸溶液中浸渍以后通过测定质量损耗对密封阳极处理氧物涂层进行质量评定

Aluminium and aluminium alloys - Anodizing - Part 6: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment; German version EN 1237

DIN EN 12373-9:1999 铝和铝合金.阳极化处理.第9部分:用砂轮磨损试验测量阳极处理氧化涂层的耐磨损性和磨损指数

The document specifies a method of test for determining the wear resistance and the wear index of anodic oxidation coatings on flat specimens of aluminium and aluminium alloys by means of an abrasive wheel test apparatus. The wear resistance or the wear index of the layers of oxide near the surface of the whole oxidation coatings thickness, or of any selected intermediate zone can be determined. The method is applicable to all anodic oxidation coatings of thickness no less than 5?on flat aluminium specimens.#,,#

Aluminium and aluminium alloys - Anodizing - Part 9: Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus; German version EN 12373-9:1998

DIN EN 12373-5:1999 铝和铝合金.阳极处理.第5部分:用测量公差方法对密封的阳极处理氧化涂层进行质量评定

This test is intended to give a quick, non-destructive assessment of the quality of sealed anodic oxide coatings and is therefore very suitable as a routine production control. It is also suitable for use as an acceptance test.#,,#

Aluminium and aluminium alloys - Anodizing - Part 5: Assessment of quality of sealed anodic oxidation coatings by measurement of admittance; German version EN 12373-5:1998

DIN EN 12373-8:1999 铝和铝合金.阳极处理.第8部分:着色阳极氧化处理氧化涂层的耐紫外线和热影响比较牢度的测定

This document specifies a comparative method for the determination of the fastness of coloured anodic oxidation coatings to ultra-violet light and heat. The method is not suitable for testing coloured anodic oxidation coatings that are heat sensitive.

Aluminium and aluminium alloys - Anodizing - Part 8: Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings; German version EN 12373-8:1998

NF A91-421:1988 表面处理.阳极氧化铝和铝合金.45°镜面反射率.总反射率.成象清晰度

SURFACE TREATMENTS. ANODIZED ALUMINIUM AND ALUMINIUM ALLOYS. MEASUREMENT OF REFLECTANCE CHARACTERISTICS OF ALUMINIUM SURFACES USING INTEGRATING SPHERE INSTRUMENTS.

BS 6161-14:1987 铝及铝合金阳极氧化镀层试验方法.第14部分:红外反射率测定

A method whereby a test piece is blackened on one side. Heating curves are then prepared by exposing first the blackened, then the unblackened sides to a radiation source.

Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of infra-red reflectance

BS 6161-11:1985 铝及铝合金阳极氧化镀层试验方法.第11部分:光电反射计测量总反射率

This Part of BS 6161 describes a method of measuring the total reflectance of flat surfaces of anodized aluminium using a photoelectric reflectometer. The method is applicable to achromatic (non-coloured) surfaces of any texture or lightness. It is regarded as an approximate method and is most suitable for production control purposes. NOTE. The titles of the publications referred to in this standard are listed on the inside back page.

Methods of test for anodic oxidation coatings on aluminium and its alloys - Measurement of total reflectance using a photoelectric reflectometer

BS 6161-7:1984 铝及其合金阳极氧化镀层试验方法.第7部分:阳极氧化有色镀层的人造光耐光度加速测定法

This Part of this British Standard describes an accelerated method for determining the light fastness of coloured anodic oxidation coatings, using artificial light. The method is applicable to coloured anodic oxidation coatings on aluminium and its alloys, produced by any means and for any purpose. It is suitable for quality control testing of coloured anodic oxidation coatings whose light fastness rating has already been established by means of outdoor exposure testing. It is not suitable for the evaluation of coloured anodic oxidation coatings with a light fastness rating of less than 6. NOTE 1. This method is not suitable for evaluating light fastness under exterior exposure, as only outdoor testing under conditions comparable to actual service is completely satisfactory. NOTE 2. The titles of the publications referred to in this standard are listed on the inside back page.

Methods of test for anodic oxidation coatings on aluminium and its alloys - Accelerated determination of light fastness of coloured anodic oxidation coatings using artificial light

BS 6496:1984 施加并焙固于铝合金的挤压材、板材和预成型材(外部建筑用)的粉末有机涂层和带有粉末有机涂层的铝合金挤压材、板材和预成型材的精饰规范

Requirements for coatings before and after their application. Also specifies the pretreatment of the aluminium alloy. (See also BS 4842 and BS 6497).

Specification for powder organic coatings for application and stoving to aluminium alloy extrusions, sheet and preformed sections for external architectural purposes, and for the finish on aluminium alloy extrusions, sheet and preformed sections coated wi

ASTM B580-79(2004) 铝阳极氧化镀层

1.1 This specification covers requirements for electrolytically formed porous oxide coatings on aluminum and aluminum alloy parts in which appearance, abrasion resistance, electrical properties, and protection against corrosion are important. Nonporous, barrier layer anodic coatings used for electrical capacitors are not covered. Seven types of coatings as shown in are provided. Definitions and typical examples of service conditions are provided in Appendix X1. Note 18212;It is recognized that uses exist in which modifications of the coatings covered by this specification may be required. In such cases the particular properties desired by the purchaser should be the subject of agreement between the purchaser and the manufacturer.

Standard Specification for Anodic Oxide Coatings on Aluminum