E43;Q27 标准查询与下载

DIN EN 13074-1:2011 沥青和沥青粘合剂.从沥青乳胶或缩减或溶剂沥青结合料中回收粘合剂.第1部分:蒸发回收;德文版本EN 13074-1-2011

This European Standard specifies a method for the recovery of binder from a bituminous emulsion or from a cut-back or fluxed bitumen after conditioning at ambient temperature for 24 h followed by 24 h at 50 °C, in such a way that will enable further testing with minimum changes of the binder characteristics. It applies to all types of bituminous emulsions, modified with polymers or non-modified, as well as to all types of cut-back and fluxed bitumens, both modified with polymers and non-modified. For cut-back and fluxed bituminous binders, this test method is only an intermediate step and should be followed by the stabilisation procedure specified by EN 13074-2. Direct testing of the recovered binder is however used to evaluate the setting ability of fluxed bituminous binders made with vegetal fluxes. NOTE The recovered binder is not necessarily identical to the initial binder. WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. The hazards associated with the use of this method have been assessed using cut-back bitumen containing 10 % kerosene and 90 % 160/220 penetration grade bitumen and were found low enough to be acceptable. However it is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Bitumen and bituminous binders - Recovery of binder from bituminous emulsion or cut-back or fluxed bituminous binders - Part 1: Recovery by evaporation; German version EN 13074-1:2011

DIN 52006-2:2006 沥青和沥青粘合剂.水对粘合剂涂层作用的测定试验方法.第2部分:石油轻制粘合剂涂层

This standard specifies a method for the determination of the adhesivity of petroleum cutback binder coating in water.

Bitumen and bituminous binders - Test methods for the determination of the effect of water on binder coatings - Part 2: Petroleum cutback binder coating

DIN 52006-1:2006 沥青和沥青粘合剂.水对粘合剂涂层作用的测定试验方法.第1部分:乳化沥青粘合剂涂层

This standard specifies a method for the determination of the adhesivity of the bitumen emulsion binder coating to the stone in water.

Bitumen and bituminous binders - Test methods for the determination of the effect of water on binder coatings - Part 1: Bitumen emulsion binder coating

DIN 52006-3:2006 沥青和沥青粘合剂.水对粘合剂涂层作用的测定试验方法.第3部分:软制沥青粘合剂涂层

This standard specifies a method for visually determining the loss of adhesion of binder coatings after curing fluxed bitumen due to the action of water of room temperature. The test is carried out with a basaltic chips specified as reference material.

Bitumen and bituminous binders - Test methods for the determination of the effect of water on binder coatings - Part 3: Fluxed bitumen binder coating

ASTM D6511-06 溶剂承载沥青复合物的标准试验方法

These tests are useful in sampling and testing solvent bearing bituminous compounds to establish uniformity of shipments.1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and waterproofing.1.2 The test methods appear in the following order:1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Solvent Bearing Bituminous Compounds

ASTM D6511/D6511M-06(2011)e1 溶剂负载沥青复合物的标准试验方法

These tests are useful in sampling and testing solvent bearing bituminous compounds to establish uniformity of shipments.1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and waterproofing. 1.2 The test methods appear in the following order: Section Sampling4 Uniformity5 Weight per gallon6 Nonvolatile content7 Solubility8 Ash content9 Water content10 Consistency11 Behavior at 60°C [140°F]12 Pliability at –0°C [32°F]13 Aluminum content14 Reflectance of aluminum roof coatings15 Strength of laps of rolled roofing adhered with roof adhesive16 Adhesion to damp, wet, or underwater surfaces17 Mineral stabilizers and bitumen18 Mineral matter19 Volatile organic content20 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Solvent Bearing Bituminous Compounds

ASTM D6114-97(2002) 沥青橡胶粘结剂的标准规范

1.1 This specification covers asphalt-rubber binder, consisting of a blend of paving grade asphalt cements, ground recycled tire (that is, vulcanized) rubber and other additives, as needed, for use as binder in pavement construction. The rubber shall be blended and interacted in the hot asphalt cement sufficiently to cause swelling of the rubber particles prior to use.Note 18212;It has been found that at least 15 % rubber by weight of the total blend is usually necessary to provide acceptable properties of asphalt-rubber.1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.1.3 The following precautionary caveat pertains to the test method portions only, Sections 4 and 5 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 4.3.2.

Standard Specification for Asphalt-Rubber Binder