Z23 工业废水、污染物分析方法 标准查询与下载



共找到 135 条与 工业废水、污染物分析方法 相关的标准,共 9

General rules for analytical and testing methods of coal mine water

ICS
13.060.30
CCS
Z23
发布
2017-05-12
实施
2017-12-01 00:00:00.0

本标准规定了实验室测定工业废水鱼类急性毒性的试验范围、方法概述、试验准备、试验仪器、试样的采集及保存、试验条件、适用操作和试验结果。 本标准适用于工业废水鱼类急性毒性的测定。

Testing methods for industrial wastewater.Fish acute toxicity

ICS
13.300;13.020.40
CCS
Z23
发布
2008-05-12
实施
2008-09-01

本标准适用于水和废水中1,2二氯苯、1,4-二氯苯、1,2,4-三氯苯的测定。 本方法最低检出浓度(μg/L):1,2二氯苯为2;1,4-二氯苯为5;1,2,4-三氯苯为1。

Water quality--Determination of 1,2-dichlorobenzene, 1,4-dichlorobenzene, 1,2,4-trichlorobenzene--Gas chromatography

ICS
13.160.01
CCS
Z23
发布
1997-12-08
实施
1998-05-01

本方法适用于地面水、地下水及生活污水、造纸废水、石油化工废水、炼焦废水与印染废水中的溶解性的HS、HS、S以及存在于颗粒物中的可溶性硫化物、酸溶性的金属硫化物的测定。当取样体积为250ml用500ml“硫化氢吸收显色剂”,1cm比色皿测定,硫化物的最低检出限为0004mg/L,测定浓度范围为0008~25mg/L。

Water quality--Determination of sulfide--Direct development of the spectrophotometry

ICS
13.160.01
CCS
Z23
发布
1997-12-08
实施
1998-05-01

本标准适用于水中挥发性卤代烃(三氯甲烷、四氯化碳、三氯乙烯、四氯乙烯、三溴甲烷)测定。 本方法的最低检出浓度(μg/L):三氯甲烷为0.30;四氯化碳为0.05;三氯乙烯为050;四氯乙烯为0.2;三溴甲烷为1。

Water quality--Determination of volatile halogenated organic compounds--Headspace gas chromatography

ICS
13.060.01
CCS
Z23
发布
1997-12-08
实施
1998-05-01

本标准规定测定水中可吸附在活性炭上的有机卤化物(AOX)的微库仑法,在吸附前必要时先经过吹脱,挥发性的有机卤化物可以直接测定。 本标准适用测定饮用水、地下水、地面水、污水中有机卤化物(AOX),其测定范围为10~400μg/L如超过上限,可减少取样量。 如水样中溶解的有机炭>10mg/L,无机氯化物含量>1g/L时,分析前必须稀释。 当水样中存在悬浮物时,其所含有的有机卤物素化合物也包括在测定值中。 为避免从水相中分离活性炭时可能形成的胶体干扰,需加入助滤剂如硅藻上,使炭絮凝克服过滤的困难。 当水样中含有活性氯时,AOX的值会偏高;故采样后需立即加入亚硫酸钠。当水样中存在难溶解的无机氯化物,生物细胞(如微生物、藻类)等,样品需要先酸化,放置8h后再分析。 无机碘化物可以干扰吸附和检测,有机碘化物会导致非重视性的高结果,高浓度的无机溴化物也有干扰。

Water quality--Determination of adsorbable organic halogens (AOX)--Microcoulometric method

ICS
13.060.40
CCS
Z23
发布
1995-12-21
实施
1996-08-01

本标准规定了测定水中二乙烯三胺的水杨醛分光光度法。 本方法适用于地面水、航天工业废水中二乙烯三胺的测定。 二乙烯三胺的测定范围:0.4~3.2mg/L。水样中二乙烯三胺含量大于3.2mg/L时,可稀释后按本方法测定。 水中存在偏二甲基肼、硝基甲烷、NH+4等干扰物,其浓度为二乙烯三胺浓度5倍以内时,干扰很小,可不计;水中存在二甲苯胺、三乙胺、NO-3、NO-2等干扰物,其浓度为二乙烯三胺浓度10倍以内时,干扰很小,可不计;甲醛含量高于0.8mg/L时,会产生负干扰。

Water quality. Determination of diethylenetriamine. Salicyiclaldehyde spectrophotometric method

ICS
13.060.40
CCS
Z23
发布
1993-05-22
实施
1993-12-01

本标准规定了测定水中偏二甲基肼的氨基亚铁氰化钠分光光度法。 本方法适用于地面水、航天工业废水中偏二甲基肼的测定。 偏二甲基肼的测定范围:0.01~1.0mg/L。水样中偏二甲基肼含量大于1.0mg/L时,可稀释后按本方法测定。 氨、尿素对本方法测定基本无干扰。肼、一甲基肼、甲醛含量在偏二甲基肼含量5倍以上干扰测定。

Water quality. Determination of asymmetrical dimethyl hydrazine. Amino ferrocyanide sodium spectrophotometric method

ICS
13.060.40
CCS
Z23
发布
1993-05-22
实施
1993-12-01

本标准规定了测定水中一甲基肼的对二甲氨基苯甲醛分光光度法。 本方法适用于地面水、航天工业废水中一甲基肼的测定。 一甲基肼的测定范围为0.02~0.80mg/L。水样中一甲基肼含量大于0.80mg/L时,可稀释后测定。 肼干扰一甲基肼的测定。偏二甲基肼含量高于一甲基肼时,可用校正曲线预以校正。

Water quality. Determination of monomethyl hydrazine. p-Dimethylaminobenzaldegyde spectrophotometric method

ICS
13.060.40
CCS
Z23
发布
1993-05-22
实施
1993-12-01

本标准规定了测定水中三乙胺的溴酚蓝分光光度法。 本方法适用于地面水、航天工业废水中三乙胺的测定。 三乙胺的测定范围:0.5~3.5mg/L。水样中三乙胺含量大于3.5mg/L时,可稀释后按本方法测定。

Water quality. Determination of triethylamine. Bromophenol blue spectrophotometric method

ICS
13.060.40
CCS
Z23
发布
1993-05-22
实施
1993-12-01

本标准规定了金属材料及其他相关固体材料热膨胀特征参数测量方法的定义及符号、原理、测试装置与要求、试样制备、膨胀仪校正、测量程序、测量结果计算、试验报告、精度与偏差等。 本标准适用于借助由同种熔融石英载体与推杆构成的组件,在-180~900℃温度范围内,检测金属材料试样的线性热膨胀,也适用于陶瓷、耐火材料、玻璃、岩石等具有刚性固体特征的试样的线性热膨胀的检测;若改用高纯度氧化铝的组件,温度范围可扩至1600℃;改用各向同性的石墨,则可扩至2500℃。

Discharge standard of water pollutants for dyeing and finishing of textile industry

ICS
13.060.30
CCS
Z23
发布
1992-05-13
实施
1992-07-01

本标准适用于经过处理或初步处理后的雷汞废气中的耗氧值和氧化氮的测定。适用范围耗氧值2~200mg/L,氧化氮1~100mg/m3。

Waste gas from manufacturing process--Determination of chemical oxygen demand and nitrogen oxide--Potassium dichromate oxidation and naphthylethylene diamine colorimetric method

ICS
13.060.40
CCS
Z23
发布
1985-01-18
实施
1985-08-01

本方法适用于梯恩梯生产废水及排放废水中的一硝基甲苯、二硝基甲苯、三硝基甲苯及其异构物等主要硝基化合物测定(不包括硝基化合物的盐)。

Waste water from manufacturing process--Determination of total nitro compounds--Gas chromatographic method

ICS
13.060.40
CCS
Z23
发布
1985-01-18
实施
1985-08-01

Determination of Total Nitro Compounds in Industrial Wastewater by Gas Chromatography

ICS
CCS
Z23
发布
1985-01-18
实施
1985-08-01

本方法适用于梯恩梯生产废水中三硝基化合物(以2,4,6-三硝基甲苯计)和一硝基化合物、二硝基化合物(以2,4-二硝基甲苯计)总和的测定。

Waste water from manufacturing process--Determination of total nitro compounds--Spectrophotometric method

ICS
13.060.40
CCS
Z23
发布
1985-01-18
实施
1985-08-01

本标准规定了测定水中甲基汞和乙基汞的液相色谱-原子荧光法。 本标准适用于地表水、地下水、生活污水、工业废水和海水中甲基汞和乙基汞的测定。 取样体积为 1 L,反萃取液体积为 3.0 ml,进样体积为 100 μl 时,方法检出限为 0.08 ng/L~0.1 ng/L, 测定下限为 0.32 ng/L~0.4 ng/L。详见附录 A。

Water quality—Determination of methyl mercury and ethyl mercury—Liquid chromatography - atomic fluorescence spectrometry

ICS
13.060.50
CCS
Z23
发布
2022-12-12
实施
2023-06-15

本标准规定了测定水中丁基黄原酸的吹扫捕集/气相色谱-质谱法。 本标准适用于地表水、地下水、生活污水和工业废水中丁基黄原酸的测定。 本标准不适用于含盐量高于25 g/L 的高盐工业废水以及存在代森锌(锰)类农药或二乙基二硫代氨基甲酸盐(如:铜试剂)等物质水样的测定。 若水样中检出丁基黄原酸,必要时可选用其他分析方法进一步确认。 当取样体积为5 ml 时,丁基黄原酸的检出限为0.04μg/L,测定下限为0.16μg/L。

Water quality – Determination of butyl xanthate-Purge and trap/gas chromatography-mass spectrometry

ICS
13.060
CCS
Z23
发布
2017-12-21
实施
2018-02-01

ERRATUM

ICS
CCS
Z23
发布
2017-01-05
实施

Water quality - Determination of volatile organic compounds in water - Method using headspace solid-phase micro-extraction (HS-SPME) followed by gas chromatography-mass spectrometry (GC-MS) (ISO 17943:2016); German version EN ISO 17943:2016

ICS
13.060.50
CCS
Z23
发布
2016-10
实施

This European Standard specifies requirements, test methods, evaluation of conformity and marking for prefabricated secondary treatment units used for the treatment of effluent from septic tanks according to EN 12566-1 or EN 12566-4 in small wastewater treatment systems for up to 50 PT. NOTE Equivalent septic effluent may come from existing septic tanks. It applies to the prefabricated secondary treatment unit, where all its components are packaged or site-assembled and placed on the market as a kit by one manufacturer. The prefabricated secondary treatment unit consists of one or more tanks made of concrete, steel, unplasticised polyvinylchloride (PVC-U), polyethylene (PE), glass reinforced polyester (GRP-UP), polypropylene (PP), polydicyclopentadiene (PDCPD) or container made of flexible sheets (HDPE, PP, PVC, EPDM). Other components specified by the manufacturer, such as pipes, pumps and filter material will be considered as part of the unit. This European Standard establishes the performance of the prefabricated secondary treatment units needed to verify their suitability for the end use conditions for which the test methods are specified. This European Standard applies for the packaged and/or site assembled secondary treatment units for use on the top of the ground (outside the building) or buried in the ground where no vehicle loads are applied to the unit. This European Standard does not cover: - non watertight secondary treatment units with direct infiltration into the ground; - retrofit kits.

Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent

ICS
13.060.30
CCS
Z23
发布
2016-08
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号