01.040.49 航空器和航天器技术 (词汇) 标准查询与下载

GB/T 30114.6-2014 空间科学及其应用术语 第6部分:航天医学

GB/T 30114的本部分界定了航天医学领域需要统一的一些常用术语及其定义。本部分适用于航天医学领域相关标准的制定、技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 6: Space medicine

GB/T 30114.7-2014 空间科学及其应用术语 第7部分:微重力科学

GB/T 30114的本部分界定了空间微重力科学领域中需要统一的常用科学与技术词汇和定义。本部分适用于空间微重力科学相关标准的制定、技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 7:Microgravity science

GB/T 30114.5-2014 空间科学及其应用术语 第5部分:空间生命科学和生物技术

GB/T 30114的本部分界定了空间生命科学和生物技术领域需要统一的常用术语及其定义。本部分适用于空间生命科学和生物技术领域相关标准的制定,技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 5: Space life science and biotechnology

GB/T 30114.4-2014 空间科学及其应用术语 第4部分:月球与行星科学

GB/T 30114的本部分界定了月球与行星科学领域需要统一定义的常用科学与技术词汇和定义。本部分适用于月球与行星科学相关标准的制定,技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 4:Lunar and planetary science

GB/T 30114.2-2014 空间科学及其应用术语 第2部分:空间物理

GB/T 30114的本部分界定了空间物理与应用领域需要统一定义的常用技术词汇和定义。本部分适用于空间物理与应用相关标准的制定,技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 2:Space physics

GB/T 30114.3-2014 空间科学及其应用术语 第3部分:空间天文

GB/T 30114的本部分界定了空间天文学领域需要统一定义的常用技术词汇和定义。本部分适用于空间天文学领域相关标准的制定,技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 3: Space astronomy

GB/T 30114.1-2013 空间科学及其应用术语 第1部分:基础通用

GB/T 30114的本部分界定了空间科学及其应用领域需要统一定义的基础通用术语。本部分适用于空间科学及其应用领域相关标准的制定,技术文件的编制,以及有关的科技交流和工程应用。

Terminology for space science and application.Part 1:General

GB/T 29079-2012 航天器轨道分类及常用参数符号

本标准规定了航夭器的轨道分类及航天器轨道的常用参数符号。 本标准适用于人造地球卫星、飞船、空间站以及深空探测器等航夭器的总体设计、轨道设计及相关技术活动慢对于中心引力体为地球以外其他夭体的深空探测器可参照使用”2′1

Classification and parameter symbols for orbits and trajectories of spacecraft

T/AOPA 0058-2024 民用无人驾驶航空器机载ADS-B IN设备通用要求

    近年来，伴随着低空空域的开放，民用无人驾驶航空器迎来了迅猛发展的新局面。随着民用无人驾驶航空器规模不断发展，对安全飞行、低空空域利用以及运行效率都提出了更高的要求，针对民用无人驾驶航空器的特点，为其配备相应的监视系统势在必行。ADS-B IN能够为运输航空器的空域运行提供有效的监视手段，而我国低空空域的民用无人驾驶航空器并没有完全实现搭载ADS-B IN系统。进入21世纪以来，低空空域对民用无人驾驶航空器的监视手段不足而导致的飞机不安全事件屡屡发生，而ADS-B IN设备可为民用无人驾驶航空器提供周围空域内其他航空器的监视信息，可辅助航空器间协同避撞以始终保持安全状态运行，对低空空域进行有效管控以保障低空安全，同时可减小航空器对低空空域资源的占用率，有效提升空域资源的利用率及航空器运行效率和应用范围。     中国民航高度重视新监视技术的应用与实施，不断加强ADS-B监视等技术的研究与应用，并且该技术具有部署成本低、精度高、更新快等优点，但我国民航主管部门目前还没有专门制定对民用无人驾驶航空器的ADS-B IN设备的标准和规范。因此，为规范我国民用无人驾驶航空器机载ADS-B IN设备的研制、选型和应用，进一步明确民用无人驾驶航空器机载ADS-B IN设备组成、功能、性能、接口、安全维护等要求，经反复论证、协调和修改，充分征求行业专家和管理部门的意见后形成本文件。     本文件适用于民用无人驾驶航空器机载ADS-B IN设备的研发、安装、测试、许可和维护。     本文件为首次发布。

General requirements for airborne ADS-B IN equipment of civil unmanned aircraft

ASTM F3377-23 与商业太空飞行有关的标准术语

Standard Terminology Relating to Commercial Spaceflight

ASTM D3878-23 复合材料的标准术语

1.1 These definitions cover generic terms, including terms of commercial importance, that appear in one or more standards on composites containing high-modulus (greater than 20 GPa (3 × 106 psi)) fibers. 1.2 The definitions cover, in most cases, special meanings used in the composites industry. No attempt has been made to include common meanings of the same terms as used outside the composites industry. 1.3 Definitions included have, in general, been approved as standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology for Composite Materials

T/IOT 0105-2023 卫星物联网应急求救终端标准

本标准主要规定了遇险人员主动报警定位终端的一般要求、功能要求、性能要求等。 本标准适用于各种野外作业人员配备的，通过天启星座传输报警定位信息的终端产品。

Satellite IoT Emergency Rescue Terminal Standard

T/IOT 0104-2023 卫星物联网通信数据终端标准

卫星物联网数据终端的基本功能包括： 1) 接收卫星广播信号，需符合天启星座载荷空口协议； 2) 接收卫星下行信号，需符合天启星座载荷空口协议； 3) 发送上行信号给卫星，需符合天启星座载荷空口协议； 4) 定位功能，能够接收 GNSS 信号，计算出自身的位置； 5) 工作模式管理功能，由于终端大部分时间处在无人位置，为节省能耗，需要自动管理工作模式， 根据业务需求，定时唤醒和睡眠。

Satellite Internet of Things communication data terminal standard

ASTM F3341/F3341M-23 无人机系统标准术语

1.1 This terminology standard covers definitions of terms and concepts related to unmanned aircraft systems (UAS). It is intended to encourage the consistent use of terminology throughout all ASTM unmanned aircraft system standards and is intended to complement F3060 Standard Terminology for Aircraft. Terms already included in Terminology F3060 are not duplicated here. 1.2 A definition adapted from a particular standard within the ASTM F38 collection of standards is not limited to use within only those standards. 1.3 Additional terms specific to a given standard may be defined solely within that standard and not included here. 1.4 Units—The definitions of units will be as defined in NIST SP 330, and will not be duplicated in this document. NIST SP 330 is available on the internet.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology for Unmanned Aircraft Systems

ASTM F3341/F3341M-22 无人机系统标准术语

1.1 This terminology standard covers definitions of terms and concepts related to unmanned aircraft systems (UAS). It is intended to encourage the consistent use of terminology throughout all ASTM unmanned aircraft system standards and is intended to complement F3060 Standard Terminology for Aircraft. Terms already included in Terminology F3060 are not duplicated here. 1.2 A definition adapted from a particular standard within the ASTM F38 collection of standards is not limited to use within only those standards. 1.3 Additional terms specific to a given standard may be defined solely within that standard and not included here. 1.4 Units—The definitions of units will be as defined in NIST SP 330, and will not be duplicated in this document. NIST SP 330 is available on the internet.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology for Unmanned Aircraft Systems

OENORM EN 4902-2021 航空航天系列 表面处理 定义和试验方法

Aerospace series - Surface treatments - Definitions and test methods

BS ISO 8153-2:2021 航空航天流体系统和部件 词汇配件和联轴器

Aerospace fluid systems and components. Vocabulary. Fittings and couplings

ISO 8153-2:2021 航空航天流体系统和部件.词汇.第2部分：配件和联接器

This document defines terms which are used for all types of fittings and couplings.

Aerospace fluid systems and components - Vocabulary - Part 2: Fittings and couplings

prEN 4902-2021 航空航天系列 表面处理 定义和试验方法

Aerospace series - Surface treatments - Definitions and test methods

GSO ISO 16682:2021 航空航天系列 夹紧装置的术语

ISO 16682:2015 specifies the various clamp styles, dimensional references, and terminology necessary for a clear understanding of part standards, specifications, and correspondence regarding these devices based on UK English language.

Aerospace series — Terminology for clamping devices