13.040.30;25.160.10 标准查询与下载

DIN EN ISO 15011-5:2012 焊接及相关工艺的卫生安全.烟尘和气体取样的实验室方法.第5部分:鉴定时，全部或部分由有机材料组成的产品通过焊接或切割产生的热降解产物的鉴定

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 5: Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials us

BS EN ISO 15011-5:2011 焊接和相关工艺的健康与安全.烟雾和气体采样实验法.使用热解法焊接或切割完全或部分有机材料构成的产品时,热退化产品的识别

Health and safety in welding and allied processes. Laboratory method for sampling fume and gases. Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials using pyroly

EN ISO 15011-5:2011 焊接及相关工艺的卫生安全.烟尘和气体取样的实验室方法.第5部分:鉴定时,全部或部分由有机材料组成的产品通过焊接或切割产生的热降解产物的鉴定

This part of ISO 15011 specifies procedures for obtaining information about thermal degradation productsgenerated when welding, cutting through, preheating and straightening metal treated with coatings composedwholly or partly of organic substances, e.g. shop primers, paints, oils, waxes and inter?weld materials suchas adhesives and sealants. It is aimed primarily at test laboratories performing such procedures. The datagenerated can be used by coating manufacturers to provide information for inclusion in safety data sheetsand by occupational hygienists to identify thermal degradation products of significance in the performance ofrisk assessments and/or workplace exposure measurements. The data cannot be used to estimate workplaceexposure directly.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 5: Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials us

DIN EN ISO 15011-2:2010 焊接和相关工艺中的健康和安全.烟尘和气体取样的实验室方法.第2部分:在电弧焊、切削加工和刨削槽时，一氧化碳(CO),二氧化碳(CO₂),氧化氮(NO)和二氧化氮(NO₂)排放率的测定

This standard provides guidance of the determination of emission rates of gases and organic vapours generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and consider methods for sampling and analysis. The following gases and organic vapour which can be produced during arc welding are covered:carbon monoxide(CO); Carbon dioxide(CO2); Nitrogen oxide(NO); Nitrogen dioxide(NO2); Organic vapours produced in the arc welding of coated metals, e. g. primed, painted or plastic coated material.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen monoxide (NO) and nitrogen dioxide (NO<(Index)

DIN EN ISO 15011-3:2010 焊接和相关工艺的健康和安全.烟和气体取样的实验室法.第3部分:电弧焊时臭氧排放率的测定 (ISO 15011-3-2009); 德文版本 EN ISO 15011-3-2009

This International standard defines a laboratory method for measuring the emission rate of ozone, during arc welding, using a hood technique. The methodology is directed primarily at measuring ozone emission rate when using gas-shielded arc welding processes but it can also be employed with other processes e. g. selfshielded tubular-cored arc welding, providing that welding can be performed automatically under the hood. Emission rate testing can be used to evaluate the effects of welding parameters, processes, shielding gases, consumable wires etc on ozone emission rate and hence to predict, qualitatively, relative changes in exposure that will occur under the same work situations. Absolute exposure values are dependent upon other factors such as welder position with respect to the plume and draughts and cannot be predicted from emission rate values.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 3: Determination of ozone emission rate during arc welding (ISO 15011-3:2009); German version EN ISO 15011-3:2009

DIN EN ISO 15011-1:2010 焊接和相关工艺中的健康和安全.烟尘和气体的实验室取样方法.第1部分:电弧焊产生的烟尘排放率测定和烟尘采集分析(ISO 15011-1-2009); 德文版本 EN ISO 15011-1-2009

This part of European Standard describes a method for the determination of particulate fume emission rate from arc welding processes using a fume box technique. It defines a method of sampling particulate fume for chemical analysis and suggests possible analytical techniques.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis (ISO 15011-1:2009); German version EN ISO 15011-1:2009

BS EN ISO 15011-2:2009 焊接和相关工艺中的健康和安全.对电弧焊产生的烟尘和气体取样的实验室方法.在电弧焊、切削加工和刨削槽时，一氧化碳(CO)、二氧化碳(CO₂)、氧化氮(NO)和二氧化氮(NO₂)排放率的测定

This part of ISO 15011 defines laboratory methods for measuring the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) generated during arc welding, cutting and gouging, using a hood technique. The methodology is suitable for use with all open arc welding processes, cutting and gouging but different designs of hood are used depending on the process and whether or not it can be conducted automatically. The method can be used to evaluate the effects of welding wires, welding parameters, processes, shielding gases, test piece composition and test piece surface condition on emission rate.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cu

BS EN ISO 15011-1:2009 焊接和相关工艺中的健康和安全.烟尘和气体的实验室取样方法.电弧焊产生的烟尘排放率测定和烟尘采集分析

This part of ISO 15011 defines a laboratory method for measuring the emission rate of fume from arc welding. It also defines a method of collecting the fume for subsequent analysis and refers to suitable analytical techniques. The methods described are suitable for use with all open arc welding processes except tungsten inert gas (TIG) welding, which produces little fume. The emission rate method can be used to evaluate the effects of welding electrodes and wires, welding parameters, processes, shielding gases, test piece composition and test piece surface condition on fume emission rate. Following analysis of the fume collected, the effects of test parameters on fume composition can also be determined.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Determination of fume emission rate during arc welding and collection of fume for analysis

BS EN ISO 15011-3:2009 焊接和相关工艺的健康和安全.烟和气体取样的实验室法.电弧焊时臭氧排放率的测定

This part of ISO 15011 defines a laboratory method for measuring the emission rate of ozone during arc welding, using a hood technique. The method is directed primarily at measuring ozone emission rate when using gas-shielded arc welding processes, but it can also be employed with other processes, e.g. selfshielded flux-cored arc welding, provided that welding can be performed automatically under the hood. The method can be used to evaluate the effects of welding wires, welding parameters, processes, shielding gases, test piece composition and test piece surface condition on emission rate.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Determination of ozone emission rate during arc welding

NF A88-200-3*NF EN ISO 15011-3:2009 焊接和相关工艺的卫生和安全.电弧焊产生的烟尘和气体取样的试验室方法.第3部分:电弧焊过程中臭氧排放速度的测定

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 3 : determination of ozone emission rate during arc welding.

NF A88-200-1*NF EN ISO 15011-1:2009 焊接和相关工艺的卫生与安全.电弧焊产生的烟尘和气体取样的试验室方法.第1部分:颗粒烟尘排放率的测定和颗粒烟尘分析用取样

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 1 : determination of fume emission rate during arc welding and collection of fume for analysis.

NF A88-200-2*NF EN ISO 15011-2:2009 焊接和相关工艺中的卫生安全.电弧焊产生的烟尘和气体取样的试验室方法.第2部分:焊接、切断和熔刮过程中一氧化碳(CO),二氧化碳(CO2),一氧化氮(NO)和二氧化氮(NO2)的气体排放率测定

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2 : determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc we

ISO 15011-4:2006/Amd 1:2008 焊接和相关工艺中的健康和安全.烟尘和气体取样用实验室方法.第4部分:烟尘数据单.修改件1

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4: Fume data sheets; Amendment 1

ISO 15011-4:2006 焊接和相关工艺的卫生和安全.烟尘和气体取样的实验室方法.第4部分:烟尘数据单

This part of ISO 15011 covers health and safety in welding and allied processes. It specifies requirements for determination of the emission rate and chemical composition of welding fume in order to prepare fume data sheets. It applies to all filler materials used for joining or surfacing by arc welding using a manual, partly mechanised or fully automatic process, depositing unalloyed steel, alloyed steel and non-ferrous alloys. Manual metal arc welding, gas-shielded metal arc welding with solid wires, metal-cored and flux-cored wires and arc welding with self-shielded flux-cored wires are included within the scope of this part of ISO 15011.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4: Fume data sheets

JIS Z 3952:2005 焊接环境中气体浓度的测量方法

この規格は，溶接及び関連作業環境における一酸化炭素(CO)，二酸化炭素(CO )，一酸化窒素(N0)，二酸化空素((NO ),及びオゾン(0 )の作業環境気中ガス濃度並びに作業者の個人ばく露ガス濃度を測定する方法について規定する。

Methods of measurement for gas concentration in welding environment

JIS Z 3950:2005 焊接环境中气载灰尘浓度的测量方法

この規格は，溶接及び関連作業環境における浮遊粉じん(以下，粉じんという。)の作業環境気中粉じん質量濃度及び作業者の個人ばく露粉じん質量濃度を測定する方法について規定する。

Methods of measurement for airborne dust concentration in welding environment

BS EN ISO 15011-2:2003 焊接和相关工艺的卫生和安全.电弧焊产生的烟和气体取样的实验室法.除臭氧外的气体排放率的测定

ISO 15011-2:2003 provides guidance on the determination of emission rates of gases generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and considers methods for sampling and analysis. The following gases that can be produced during arc welding are covered: - carbon monoxide (CO); - carbon dioxide (CO2); - nitrogen oxide (NO); - nitrogen dioxide (NO2). The fume box described in this International Standard may also be used for the determination of organic gases produced in the arc welding of coated metals, e.g. primed, painted or plastic coated material.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rates of gases, except ozone

ISO 15011-2:2003 焊接和相关工艺中的保健和安全.对电弧焊产生的烟尘和气体取样的实验室方法.第2部分:除臭氧外气体的排放率的测定

This European Standard provides guidance on the determination of emission rates of gases generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and considers methods for sampling and analysis. The following gases that can be produced during arc welding are covered: - Carbon monoxide (CO); - Carbon dioxide (CO2); - Nitrogen oxide (NO); - Nitrogen dioxide (NO2). The fume box described in this standard can also be used for the determination of organic gases produced in the arc welding of coated metals, e.g. primed, painted or plastic coated material (see annex A for further information). Ozone is considered in EN ISO 15011-3.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone

BS EN ISO 15011-1:2002 焊接和有关加工工艺中的健康和安全性.电弧焊接产生的烟尘和气体的实验室取样方法.排放率测定和颗粒烟尘分析的取样

This European standard describes a method for the determination of the particulate fume emission rate from arc welding processes using a fume box technique. It defines a method of sampling particulate fume for chemical analysis and suggests possible analytical techniques in order to characterize fumes emitted by consumable during welding.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rate and sampling for analysis of particulate fume

ISO 15011-1:2002 焊接和有关过程中的健康和安全.电弧焊接产生的取样烟尘和气体的实验室方法.第1部分:颗粒烟尘分析的排放率测定和取样

This European standard describes a method for the determination of the participate fume emission rate from arc welding processes using a fume box technique. It defines a method of sampling particulate fume for chemical analysis and suggests possible analytical techniques in order to characterize fumes emitted by consumable during welding.

Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 1: Determination of emission rate and sampling for analysis of particulate fume